Replasticizing hop balls

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Guest

    #16
    Re: Replasticizing hop balls

    Let some air out, plugged it, spun it around a few minutes under hot shower, reinflated until tight to push down on. It's now up to 73" circumference. Thin spots in the vinyl are starting to show so it's really close to as big as it's going to get and still be usable. Not super bouncy but decent enough. This is the point where I wouldn't mind the plasticizer really relaxing it and ballooning the size even if it risks popping.

    Forgot to add that if anything feels different, the handle does (I coated it too). It is softer and more flexible but then it's never really under any pressure stress so it doesn't help.
    Last edited by Guest; 07-07-2021, 12:49.

    Comment

    • Guest

      #17
      Re: Replasticizing hop balls

      Another coating (exterior) with ATBC followed by an even blasting with the hair dryer to soak it in, then another inflate until tight. Measurements now 74"/23.6" around the middle, 74.75"/23.8" pole to pole. Will apply occasional heat and leave it hang for several more days.

      There is now a slight but noticeable bulge on the upper back (the seat) indicating that the plasticizer has worked to stretch this area under stress of bouncing. Need to work on stretching the rest of it the same way by rotating the ball so I can sit on all sides while riding.
      Last edited by Guest; 07-07-2021, 17:32.

      Comment

      • Guest

        #18
        Re: Replasticizing hop balls

        HH is still bouncy enough to ride, not rock hard, but no matter what the 66 is an all around better hopper.

        If I was a millionaire, I would find a company to duplicate the same stiffer vinyl and design that Sun used, but in a 26 inch ball. If only Sun had marketed the 25" prototype they tested.
        Attached Files
        Last edited by Guest; 07-07-2021, 17:59.

        Comment

        • Guest

          #19
          Re: Replasticizing hop balls

          Unicks, the ATBC + hair dryer did result in that tacky feel you talked about, only all over the ball this time.

          Comment

          • Guest

            #20
            Re: Replasticizing hop balls

            I’m really impressed you stretched the vinyl that much! I agree and wish the original HH was much bigger. Thanks for the response !

            Comment

            • Guest

              #21
              Re: Replasticizing hop balls

              Originally posted by frenchy
              I’m really impressed you stretched the vinyl that much! I agree and wish the original HH was much bigger. Thanks for the response !
              Very welcome! Have you ever tried stretching any hoppers?

              I deflated it and found that the texture is exactly as Unicks said it should be...softer and tackier, and a deeper red color now, just like new. I have it sunning itself inside a black garbage bag along with the Great Space Hopper (also uninflated) which I've coated inside and out with ATBC. I have better hopes for increased size from this one since it was rated to 23" originally. Just can't stand those stupid horns! If it works I may be sacrificing the ring handle from a cheap blue HH.

              (pics are of one that just sold on ebay)
              Attached Files
              Last edited by Guest; 07-07-2021, 18:41.

              Comment

              • Guest

                #22
                Re: Replasticizing hop balls

                GSH was brought in and inflated while very warm. It's been pumped up a few times and coated again (absorbed the plasticizer like a sponge both times) and now is 73.25" circumference. That's a tad overinflated, it's almost rock hard. Will watch for stretching over the next few weeks.

                These old balls are so thick, and the vinyl so relatively dense, they would have to throroughly soak for a month in a barrel of plasticizer to really absorb enough, I think.
                Last edited by Guest; 08-07-2021, 03:06.

                Comment

                • Guest

                  #23
                  Re: Replasticizing hop balls

                  Great project notes! Please keep the updates coming.

                  Comment

                  • Guest

                    #24
                    Re: Replasticizing hop balls

                    GSH sat deflated for over a week after last post. Checked it today. Vinyl is definitely smoother and softer to the touch (better response than the HH). So I soaked inside and out with new coating of ATBC and am keeping it bagged in back of a hot car for a few days, then will test inflate.
                    Last edited by Guest; 19-07-2021, 15:09.

                    Comment

                    • Guest

                      #25
                      Re: Replasticizing hop balls

                      I have sun stretched modern day hoppers but I have not used ATBC. I have an original blue Hoppity Hop with the thick vinyl and metal valve. How much ATBC should I put in the hopper for a good stretch?

                      Comment

                      • Guest

                        #26
                        Re: Replasticizing hop balls

                        Originally posted by frenchy
                        I have sun stretched modern day hoppers but I have not used ATBC. I have an original blue Hoppity Hop with the thick vinyl and metal valve. How much ATBC should I put in the hopper for a good stretch?
                        Going with the Sculpey size bottles, it's going to take at least three or four, inside and out, applied and stretched over some weeks so it can really soak into the vinyl. Its back in stock as of last week.

                        Like Unicks says, consistent heating helps a lot. You will get better, faster results than I have if you use sun and ATBC (I'm not able to put mine in the sun). If you're careful you may see results in days instead of weeks.

                        If you try it, please update us on how it goes.

                        ps

                        I found dosing the inside easiest by pulling out the brass air valve. You can put it back in but once the plasticizer starts to work, it may stretch that hole a little so you may need a slightly larger plug. No big deal ... I use a modern plug so inflation is easier now.
                        Last edited by Guest; 23-07-2021, 13:17.

                        Comment

                        • Guest

                          #27
                          Re: Replasticizing hop balls

                          Inflated GSH yesterday while very warm. Stopped near rated size but the vinyl is definitely smoother and stretchier. The British vinyl is slightly heavier/denser/thicker than the HH so I will leave it sit before putting in more air.

                          Comment

                          • Guest

                            #28
                            Re: Replasticizing hop balls

                            Originally posted by frenchy
                            I have sun stretched modern day hoppers but I have not used ATBC. I have an original blue Hoppity Hop with the thick vinyl and metal valve. How much ATBC should I put in the hopper for a good stretch?
                            Bouncing around as hard as you can when it's hot and dosed with liquid also helps. Just make sure you rotate the ball while riding for even stretching (including bouncing with the handle sideways).

                            Comment

                            • Guest

                              #29
                              Re: Replasticizing hop balls

                              GSH is now 77" circumference (24.5" diameter) and around 28" high between the horns! It's almost rock hard tho, so now we'll see if there's any more stretch left in it or if this as big as it can get.
                              Last edited by Guest; 24-07-2021, 15:24.

                              Comment

                              • Guest

                                #30
                                Re: Replasticizing hop balls

                                GSH, with a little air let out, next to Husky410's 32" Hoppity Hop at about 75% full.

                                Impressed? I am!
                                Attached Files
                                Last edited by Guest; 24-07-2021, 16:12.

                                Comment

                                Working...