balloon constructs and modifications

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • DJ Looner
    Senior Member
    • Apr 2020
    • 160

    #16
    Re: balloon constructs and modifications

    No the purpose would be to give the zeppelin a larger diameter neck not longer to make it possible to climb partially inside.

    Comment

    • balloonPatcher
      Senior Member
      • Jun 2020
      • 291

      #17
      Re: balloon constructs and modifications

      Originally posted by DJ Looner
      No the purpose would be to give the zeppelin a larger diameter neck not longer to make it possible to climb partially inside.
      Oh, if that is what you want then it should be doable. Couple of things to think about.
      You may want to add an inflation nozzle on the balloon so that the enlarged neck is just for getting into the balloon. You could use another 72" balloon an cut out the enlarged nozzle from it so that the entire construct would be the same thickness of rubber. If it works you would have made something special and unique.
      My two cents.

      Comment

      • balloonPatcher
        Senior Member
        • Jun 2020
        • 291

        #18
        Re: balloon constructs and modifications

        It has been awhile since I have posted anything about balloon modification.
        This is about reducing the inflation nozzle of a cattex 72 inch wide neck.

        First I unrolled the neck for an extra 3/4" in length. This is optional.
        Cut the neck as shown leaving a 2" wide strip of the old neck. Butt end the cut pieces together with rubber adhesive. Glue strips of latex (from the cut piece of the cattex or another broken balloon) to re in force the new glued seam.
        Let dry for about 1 hour. Then you can inflate by mouth and close the 72" by rolling or with a standard balloon clip.
        Attached Files

        Comment

        • balloonPatcher
          Senior Member
          • Jun 2020
          • 291

          #19
          Re: balloon constructs and modifications

          This next construct is how to add an SPH tube to a balloon

          You need to get latex adhesive and also a solvent eg acetone or isopropyl alcohol. You will need latex from another balloon.

          1. Cut an H like piece as shown. This was from a 72" cattex. I like to use this latex because this piece is under alot of stress since it will form a loop that will pull the sph inward.

          2. cut a round donut about 2.5 to 3 inches in diameter from thick latex.
          This will serve as the re in forcement for the sph entry.

          3. on opposite sides of the balloon glue the H piece to form a loop on one side and the other side the re inforcement donut. wipe clean both latex areas and the latex pieces before glueing.
          Attached Files

          Comment

          • balloonPatcher
            Senior Member
            • Jun 2020
            • 291

            #20
            Re: balloon constructs and modifications

            4. preparing the sph from a 36" longneck.
            I like to cut off the ring from the neck. and cut out into the balloon body as shown.
            5. Glue the cut piece from the balloon body so that you have a close ended tube. Glue another H piece to form another loop at the glued end of the sph tube.

            6. tie an elastic to the sph loop.
            Attached Files

            Comment

            • balloonPatcher
              Senior Member
              • Jun 2020
              • 291

              #21
              Re: balloon constructs and modifications

              7. tie the other end of the elastic to the loop on the opposite side of the balloon so that the elastic sph tube is attached.

              8. For me this is the most difficult part for a non-popper. Cut a smooth hole in the middle of the donut for the sph tube.

              9. invert the entire balloon inside out through the cut hole in the middle of the donut patch.

              10. position the end of the sph and glue the edges to the donut.
              Attached Files

              Comment

              • balloonPatcher
                Senior Member
                • Jun 2020
                • 291

                #22
                Re: balloon constructs and modifications

                The finished sph balloon. I test with a partial inflation and re glue any parts that leak or have not adhered properly. The tension of the sph can be adjusted by lengthening or shortening the interior latex band. You can see the loop on one side of the balloon is holding the elastic attached to the end of the sph tube.

                Definitely more work but you can inflate the balloon as normal.
                Attached Files

                Comment

                • balloonPatcher
                  Senior Member
                  • Jun 2020
                  • 291

                  #23
                  Re: balloon constructs and modifications

                  A burst balloon repair using liquid latex. This was the first time I repaired a burst balloon with liquid latex. Another member mentioned that they had patched balloons using liquid latex so I thought I would try. Reconstructed the balloon by butt ending the broken pieces with latex adhesive, then re enforced the seams with a couple of coats of liquid latex. Two layers of latex around the break seams, one on the inside and the other on the out side. It is much easier just to make another sph balloon. However, it is a real turn on for me to inflate and use a repaired balloon.
                  Attached Files

                  Comment

                  • Guest

                    #24
                    Re: balloon constructs and modifications

                    Do these really get snug enough to provide the necessary, um, tightness? Or is it more the idea of f'ing a balloon that's the turn on? Not making fun, this is an honest question.

                    I can see a Soshu type sph working if the vinyl is thick-walled enough to offer resistance, but not a thin latex tube under what little pressure is inside a balloon. Does it really work?

                    Comment

                    • balloonPatcher
                      Senior Member
                      • Jun 2020
                      • 291

                      #25
                      Re: balloon constructs and modifications

                      Tightness
                      1. The elastic pulls on the sph - thicker and shorter the elastic the tighter
                      2. The inflation stretches the elastic - more inflation the tighter
                      3. The thickness of the balloon - thicker latex of the balloon the tighter

                      Softness
                      1. thickness of the insert - thicker the latex the firmer
                      2. width /diameter of the insert - smaller the insert the tighter

                      The feel with the set-up pictured is very very flesh like and comparable to
                      a silicone or TPE masterbator in my opinion. For me it is the very realistic feel
                      of the SPH balloon. Humping sessions often last more than half an hour.
                      Last edited by balloonPatcher; 03-07-2023, 17:44. Reason: missed point

                      Comment

                      • balloonPatcher
                        Senior Member
                        • Jun 2020
                        • 291

                        #26
                        Re: balloon constructs and modifications

                        I purchased a Tilco 72" but it was very thin on one side compared to the other.
                        It only inflated to about 24" with the thin side bulging out. One member had used liquid latex for patching so I tried it and it worked great.
                        There were 2 coats in some places and 3 coats in thinner area but the balloon now inflates evenly. The picture are at about 48". I used a mold making latex.
                        Just cleaned the balloon surface and spread out onto the balloon.

                        Attached Files

                        Comment

                        • balloonPatcher
                          Senior Member
                          • Jun 2020
                          • 291

                          #27
                          I have not posted here for quite a while now. I have been modifying balloons by coating them with liquid latex.
                          Below is a pre-stretched tuftex 24". It was getting a bit old and thin. First clean with soap and water then wash with
                          a solvent like acetone or isopropyl alchohol. Then using the tongue depressor, spread liquid latex over the surface
                          of the balloon. Next smooth the latex to a more even coat and let air dry. With a couple of coats, the final weight of
                          the 24" was increase to over 50 grams for a strong thick balloon. This technique can be used to 'restore' old vintage
                          balloons, or just to strengthen balloons something like double or triple stuffing balloons.



                          Tuftex24a.jpg Tuftex24b.jpg Tuftex24c.jpg
                          Attached Files

                          Comment

                          • balloonPatcher
                            Senior Member
                            • Jun 2020
                            • 291

                            #28
                            A repair of a 24" BK clear that was pushed a bit too far.
                            First all the pieces are re assembled using latex adhesive. I apply the adhesive to a tooth pick to both edges of the broken latex. Let dry about 30 second to 1 minute and butt end the pieces together. In this way you can reassemble the balloon. At this point it is not inflatable, has many leaks and the seams are not strong enough to be stretched. To strengthen the seams a layer of liquid latex was coated over all the seams a let dry. The balloon now will hold air but the seams are still not
                            strong enough to be stretched and inflated.

                            24bkBurst01a.jpg 24bkBurst02a.jpg 24bkBurst03a.jpg
                            Since the seams are now thicker than the rest of the balloon latex, it will inflate unevenly, so it is then coated 2-3 time with liquid latex to make
                            the latex a more even thickness over the entire balloon. The balloon will now inflate partially but the seams will still separate. So I flip the balloon
                            inside out and strengthen the seams either with liquid latex or a strip of latex from another balloon. For this repair I used the latex from a 5" balloon
                            attached with latex adhesive. Since it is essentially a new balloon, I inflate partially a couple of times before taking it to full rated size. This one still has
                            some more room at 26".24bkBurst04a.jpg 24bkBurst05a.jpg
                            It does not make sense to go through the effort to repair a balloon that costs about $1 except that I get so much pleasure from it.
                            I love to restore any rare vintage balloons.

                            Comment

                            • Folly
                              Junior Member
                              • Oct 2026
                              • 25

                              #29
                              Originally posted by balloonPatcher
                              Re: balloon constructs and modifications

                              The finished sph balloon. I test with a partial inflation and re glue any parts that leak or have not adhered properly. The tension of the sph can be adjusted by lengthening or shortening the interior latex band. You can see the loop on one side of the balloon is holding the elastic attached to the end of the sph tube.

                              Definitely more work but you can inflate the balloon as normal.
                              Thank you dearly for the instruction! I will absolutely replicate that. One question though, how easy is cleaning it? With the SPH-constructs that run through the balloon and exit the other side (as seen in this thread, where people essentially make their own geo donuts), rinsing is easy. As the SPH-tube in your instruction is closed off and furthermore tied with rubber bands inside the balloon/bladder, I imagine cleaning would be a bit tricky?

                              Comment

                              • balloonPatcher
                                Senior Member
                                • Jun 2020
                                • 291

                                #30
                                It is quite easy, take the deflated balloon to the sink and pull the sph out and rinse, dry and powder. Note: try to deflate the balloon with the sph upward to prevent fluid from dripping out.

                                Comment

                                Working...