So, other misc Inflatable objects you use.

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • glovepopper
    Senior Member
    • May 2019
    • 391

    #46
    Originally posted by AlterPlatzer
    The paper covered ones are awful, but the type in the video where it's covered with a woven plastic can be inflated very tightly and have a bouncy feeling, even though there's no stretch to them.
    I have two 90x240 cm dunnage bags covered with woven plastic - nylon? I didn't inflated this bag more than 3 psi and it was very hard then, almost didn't bend under me:

    The cool thing about them is the large valve - deflation is fast and loud

    Comment

    • bigloonfucker.cz
      Punk member
      • Nov 2023
      • 145

      #47
      Originally posted by rdk4497

      I see so the TipTop SVS is used for this process. Could you please describe it how to do this?
      At first you must be very patient and precise, when the joint isn't at 100%, while next inflation it will start pulling off and this will rip the glued latex and pop will immediately happpen. Preparin glued surface is key. For me it's enough to use wet cloth with detergent for dishes and you must scrub the surface so that after drying the surface must lose glossy look
      The softer balloon the better. When not soft enough, I bake him untill success

      Comment

      • AlterPlatzer
        Senior Member
        • Jun 2024
        • 1528

        #48
        Originally posted by glovepopper
        I have two 90x240 cm dunnage bags covered with woven plastic - nylon? I didn't inflated this bag more than 3 psi and it was very hard then, almost didn't bend under me:

        The cool thing about them is the large valve - deflation is fast and loud
        I've never paid any attention to how much pressure I put in them. I just fill them until they're tight and have a sort of bass drum sound when you tap on them.

        I really enjoy having a big inflatable to hug and bounce on.
        It's OK to love balloons.
        There are as many differences in preferences as there colors of balloons. Accentuate what makes us the same and not what sets us apart.

        Comment

        • JuliaNikolaus
          Junior Member
          • Feb 2025
          • 7

          #49
          That's a fun question. Apart from balloons, you can inflate paper cups, tennis balls, ziplock bags, and rubber gloves. Of course, they're not meant to be inflated but you can try it.

          Comment

          • bagr
            Junior Member
            • Jul 2013
            • 28

            #50
            i,m also in2 BLOWin up n playin wit BIG bags ... xmas tree disposal bags (shown), garbage bags (shown) n dry cleanin bags ... BIG, soft n BLOWn up
            Attached Files

            Comment

            • glovepopper
              Senior Member
              • May 2019
              • 391

              #51
              Originally posted by bagr
              i,m also in2 BLOWin up n playin wit BIG bags ... xmas tree disposal bags (shown), garbage bags (shown) n dry cleanin bags ... BIG, soft n BLOWn up
              I make my inflatable bags from plastic sleeves. The 90 µm thick LDPE film is quite strong. I wrote about it several posts in this thread:
              Attached Files

              Comment

              • rdk4497
                Junior Member
                • Sep 2024
                • 13

                #52
                Originally posted by bigloonfucker.cz

                At first you must be very patient and precise, when the joint isn't at 100%, while next inflation it will start pulling off and this will rip the glued latex and pop will immediately happpen. Preparin glued surface is key. For me it's enough to use wet cloth with detergent for dishes and you must scrub the surface so that after drying the surface must lose glossy look
                First of all, thanks for reply and sharing your thoughts.

                So the surface has to be prepared to get a good joint. I purchased the rubber cement svs vulc to build my first experiment and it looks pretty funny.

                I have tried to recreate one like in this video here on youtube https://youtu.be/9Rjyvg-6Sx0?si=SOBpqa55Zpuky9bv.

                So this was the outcome:

                image.pngimage.png​
                It would like to give this balloon an inner tube like in the picture below and about the glueing process to build sph balloons like them.

                Link for better resolution



                I'd like to know about the glueing process to build one sph balloon like this image.png

                So far for having nice joints we have to prepare the surface but how can this inner tube created and glued with one other balloon?

                Comment

                • cl23
                  Senior Member
                  • May 2022
                  • 381

                  #53
                  Originally posted by rdk4497
                  I'd like to know about the glueing process to build one sph balloon like this image.png

                  So far for having nice joints we have to prepare the surface but how can this inner tube created and glued with one other balloon?
                  I glued it inside out. It is made from two balloons of the same type.
                  On the first one, i made a hole left and right. On the second one, i removed the mouth piece and cut a hole into the top.
                  I put a plastic tube into the first balloon and glued like in the second picture (other balloons, same process).
                  After everything was dry, i did the opposite side.
                  After this also had been dried, i turned it back outside out and in the 3rd picture you can seen, how it looked uninflated.

                  I made this some years ago and there must be an easier way to do this and i have an idea right now, but maybe i had some reasons to do it like that, because glueing balloons still has left some mysteries. Some combinations of the same latex won't stick together, depending of if it is the inside or outside of the balloons you are trying to glue together.

                  d10.jpg k9.jpg d9.jpg

                  Comment

                  • rdk4497
                    Junior Member
                    • Sep 2024
                    • 13

                    #54
                    Thank you! That worked really well. I've tried it with an 24inch and a 36 inch.

                    Thats the outcome ->

                    20250223_124203.jpg

                    20250223_1559211.jpg

                    In this case I used for the 36 inch one and two different balloon types and it worked !

                    Great idea <3
                    Attached Files
                    Last edited by rdk4497; 23-02-2025, 19:53.

                    Comment

                    • cl23
                      Senior Member
                      • May 2022
                      • 381

                      #55
                      rdk4497
                      Congrats! That looks like a lot of fun. Now i want some of these in this size too

                      Comment

                      • rdk4497
                        Junior Member
                        • Sep 2024
                        • 13

                        #56
                        Originally posted by cl23
                        rdk4497
                        Congrats! That looks like a lot of fun. Now i want some of these in this size too
                        Thank you =). I've build another one with a GL700. It's clearly fantastic
                        The next one I will try with a GL1200 and for the inner tube maybe I'll try to use modelling balloons.
                        Attached Files

                        Comment

                        • cl23
                          Senior Member
                          • May 2022
                          • 381

                          #57
                          Wow, this looks wonderful.
                          Have you tried making a smaller one and filling it with warm water? I still want to try that.

                          Comment

                          • rdk4497
                            Junior Member
                            • Sep 2024
                            • 13

                            #58
                            Originally posted by cl23
                            Wow, this looks wonderful.
                            Have you tried making a smaller one and filling it with warm water? I still want to try that.
                            Never tried but I think it could work.

                            Comment

                            • O'Dragon
                              Senior Member
                              • Jan 2024
                              • 298

                              #59
                              Something like this could be a possibility to bring back the donut baloons.

                              Comment

                              • Gggfre
                                Junior Member
                                • Aug 2026
                                • 6

                                #60
                                Originally posted by cl23
                                Thank you! I also really love these balloons, that i made. I am working on nicer seams. That were my first tries, but enough for balloons, keeping the air for months.
                                You can create any shape, that is possible with latex.

                                Here is my proof of concept for a remake of a donut balloon and i do like the shape much more, than the original Qualatex donut:
                                d13.jpg d12.jpg
                                ... and my attempt to recreate the Q24:
                                1.jpg
                                I am working on more advanced shapes, but my gluing of narrow curves with sheet latex needs some more practice for this
                                Как ты это сделал можешь рассказать?

                                Comment

                                Working...