Progress update on custom inflates

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Big Thud Joe
    Senior Member
    • May 2017
    • 407

    Progress update on custom inflates

    Well, good to be back, after two eye operations, I feel I can get back into a normal life routine. Over the last few months, this has given me the opportunity to engage regularly with a sourcing agency in Hong Kong, who are at the present, assisting me to find a PVC fabrication plant, and good news is they are two possibilities. They both produce PVC plastic in line with the 6P reach standard, but can alter the formulation on request and not worry about any certificates or any of that other nanny shit. This is only the start of the search, so other possibilities may come up during the scouting job.

    One of the manufacturers is happy to use DEHP or DOP in their formulation, but is asking for actual data sheets of percentages. I wouldn't know where to find such material, as I would suspect such documentation would be long gone, particularly if it's from the 80s and early 90s.

    Secondly I'm rather curious about the insistency of the thickness of 0.20mm, as I've generally requested 0.10 to 0.15. I always understood the strength of an inflatables was in it's seams, and as long as it is not being thrown around in an environment that has sharp objects, that such a thin formulation would be fine.

    Also when doing a tear down of one of my beach balls that already had formed some pin-hole leaks. I found that the plastic was glossy on the outside and matte on the inside.

    I'm pretty sure that in the olden days, the agents that were added on PVCs to make them softer and shinier were added on both sides of the PVC, which resulted in both sides being shiny, and thus more perceived translucency. I would surmise by the mid to late 90s, that this would have only been added on one side to save on fabrication costs. Would this be a fair conclusion to draw?

    I've haven't said much of late, because usually when I have something in the pipeline, there is usually a snag that kind of puts everything in the shitter. Over the last ten months it was my health. But now with a recent royalty windfall, I feel now I have some space to finally get the custom inflates I want. hopefully if the desired factory and materials are found, I would gladly pass this info on once I know I can vouch for their product and quality.

    Hongyi has been mentioned several times on here, but just have a gut feeling that if I purchased one of their items, that metaphorically I'll be getting a thick clump of PVC in the post, my turn on is when inflatables are more thinner and have a sense of fragility about them.
  • Bass Boll
    Senior Member
    • Jun 2023
    • 211

    #2
    Re: Progress update on custom inflates

    Happy to hear that you kept your eyesight and things return to normal, Big Thud!

    Interesting to read your experiences with having custom toys made, always looking forward to the occasional updates. Just one remark: 0.20 mm IS already very thin for inflatables! Think of the soft Intex Wet Set Jumbo (48") beach ball of the 1990s: it had 0.25 mm ("ten gauge" = 10 milli inch) vinyl, and nowadays standard ride-ons often come at 0.28 or 0.30 mm.

    Comment

    • dchen4
      Junior Member
      • Jun 2023
      • 2

      #3
      Re: Progress update on custom inflates

      Originally posted by Big Thud Joe
      Well, good to be back, after two eye operations, I feel I can get back into a normal life routine. Over the last few months, this has given me the opportunity to engage regularly with a sourcing agency in Hong Kong, who are at the present, assisting me to find a PVC fabrication plant, and good news is they are two possibilities. They both produce PVC plastic in line with the 6P reach standard, but can alter the formulation on request and not worry about any certificates or any of that other nanny shit. This is only the start of the search, so other possibilities may come up during the scouting job.

      One of the manufacturers is happy to use DEHP or DOP in their formulation, but is asking for actual data sheets of percentages. I wouldn't know where to find such material, as I would suspect such documentation would be long gone, particularly if it's from the 80s and early 90s.

      Secondly I'm rather curious about the insistency of the thickness of 0.20mm, as I've generally requested 0.10 to 0.15. I always understood the strength of an inflatables was in it's seams, and as long as it is not being thrown around in an environment that has sharp objects, that such a thin formulation would be fine.

      Also when doing a tear down of one of my beach balls that already had formed some pin-hole leaks. I found that the plastic was glossy on the outside and matte on the inside.

      I'm pretty sure that in the olden days, the agents that were added on PVCs to make them softer and shinier were added on both sides of the PVC, which resulted in both sides being shiny, and thus more perceived translucency. I would surmise by the mid to late 90s, that this would have only been added on one side to save on fabrication costs. Would this be a fair conclusion to draw?

      I've haven't said much of late, because usually when I have something in the pipeline, there is usually a snag that kind of puts everything in the shitter. Over the last ten months it was my health. But now with a recent royalty windfall, I feel now I have some space to finally get the custom inflates I want. hopefully if the desired factory and materials are found, I would gladly pass this info on once I know I can vouch for their product and quality.

      Hongyi has been mentioned several times on here, but just have a gut feeling that if I purchased one of their items, that metaphorically I'll be getting a thick clump of PVC in the post, my turn on is when inflatables are more thinner and have a sense of fragility about them.
      I was originally from China, now moved to Australia but back in China currently have owned a swim ring that is made of a fairly thin sheet of PVC, I'm not sure of the plasticiser used but it is extremely soft, glossy and had a rubbery like stretchy feeling to it. It was made by Intime Plastics in Shanghai I believe, they are still around. It had really good quality, held most of its air while sitting for 5 years in the attic.

      Comment

      • dchen4
        Junior Member
        • Jun 2023
        • 2

        #4
        Re: Progress update on custom inflates

        You can contact their Inflatables department at +86-21-57515607 and here's their website http://www.yingtaish.com. Hope everything goes well.

        Comment

        • Big Thud Joe
          Senior Member
          • May 2017
          • 407

          #5
          Re: Progress update on custom inflates

          dchen4, if possible, would you please be able to take a photo of the ring you were referring to, it would just make it easier for me to refer to something if I'm talking to the factory. Thanks for your well wishes, will post if they are any further updates.

          Comment

          • PVC Vinyl Enthusiast
            PVC Fetish
            • Jan 2013
            • 197

            #6
            Re: Progress update on custom inflates

            Originally posted by Big Thud Joe

            One of the manufacturers is happy to use DEHP or DOP in their formulation, but is asking for actual data sheets of percentages. I wouldn't know where to find such material, as I would suspect such documentation would be long gone, particularly if it's from the 80s and early 90s .
            I am not sure what the actual percentages of the plasticizer would be, but it ought to be enough to achieve a PVC Softness of 65 to 70 PE / PHR, and with a Thickness of 200 to 250 Microns, if you want your inflatable to have a 'fragile' and thin feel to it (as you put it).

            PE (or PHR) are standardised and quantified measurements of PVC Softness. 'PE' stands for 'Phthalate Ester' value.

            Perhaps you could speak with PVC-U-Like to get an idea on the plasticizer percentages? They use soft and flexible PVC film/sheeting for making raincoats. Thickness differences aside, the PVC sheeting/film they use is not too disimilar to the PVC sheeting that could be manufactured into a silky-soft, squeaky and rubbery inflatable.
            Last edited by PVC Vinyl Enthusiast; 28-07-2023, 17:41.
            Enjoy soft, shiny and smooth PVC (inflatables and clothing). The 6P-free/10P-free material is total rubbish.

            Comment

            • Big Thud Joe
              Senior Member
              • May 2017
              • 407

              #7
              Re: Progress update on custom inflates

              Thanks Enthusiast, I will pass this info on to my sourcing agent. There has been some more developments over the last few weeks since I haven't posted.

              First, I was told in a science portion of another general interest forum that any plastics or inflatable that contain DEHP / DOP plasticizers could be blocked at Australian Customs, for not meeting up with the REACH 6p standards. I'm not sure if this is completely true, I may still have to do some further digging on this. The customs claim seemed to have come from a rather hot and bothered keyboard warrior on another forum (completely non related to looners), so I'll need to verify if this is true. This is despite the fact that these will be used for personal use, and not for resale.

              Secondly, the agent did say that even within the constraints of the REACH 6p regulations, they can still alter the formulation of the PVC enough to be softer and squeakier. (I'm rather doubtful of this until I can feel it). Though on a sidenote beachballs.com's huge 48 inch black and white balls were absolutely fantastic, if they were able to fix whatever the problem was with them. I bought three from them about three years ago, and they all had a leak at the top where the ring section joins the panels. I spoke to the proprietor about it, but his communications just went all funny and flaky, so that line of enquiry pretty much dried up.

              So to reiterate, some of the stuff I'm being told in other places needs to be verified. I would hate to have a $10,000 order blocked at customs, because of some stupid regulation. Trying to do this around my day job just takes time.

              Comment

              • PVC Vinyl Enthusiast
                PVC Fetish
                • Jan 2013
                • 197

                #8
                Re: Progress update on custom inflates

                Originally posted by Big Thud Joe
                Thanks Enthusiast, I will pass this info on to my sourcing agent. There has been some more developments over the last few weeks since I haven't posted.

                First, I was told in a science portion of another general interest forum that any plastics or inflatable that contain DEHP / DOP plasticizers could be blocked at Australian Customs, for not meeting up with the REACH 6p standards. I'm not sure if this is completely true, I may still have to do some further digging on this. The customs claim seemed to have come from a rather hot and bothered keyboard warrior on another forum (completely non related to looners), so I'll need to verify if this is true. This is despite the fact that these will be used for personal use, and not for resale.

                Secondly, the agent did say that even within the constraints of the REACH 6p regulations, they can still alter the formulation of the PVC enough to be softer and squeakier. (I'm rather doubtful of this until I can feel it). Though on a sidenote beachballs.com's huge 48 inch black and white balls were absolutely fantastic, if they were able to fix whatever the problem was with them. I bought three from them about three years ago, and they all had a leak at the top where the ring section joins the panels. I spoke to the proprietor about it, but his communications just went all funny and flaky, so that line of enquiry pretty much dried up.

                So to reiterate, some of the stuff I'm being told in other places needs to be verified. I would hate to have a $10,000 order blocked at customs, because of some stupid regulation. Trying to do this around my day job just takes time.
                Doesn't the remit of REACH only extend to consumer goods entering the EU member countries? If I am not mistaken, you are in Australia, right?

                And, as you say, the inflatable would be for your own personal use.

                By the way: the REACH restrictions are only really strict with the Low Molecular Weight class of phthalates, like DOP and DEHP. DOP and DEHP cannot be used in any toys, irrespective of the age of the child.

                The High Molecular Weight class of phthalates, such as DINP and DIDP, have been declared safe by REACH, and they can be used in PVC for inflatables and other articles.

                As a precautionary measure, DINP and DIDP are no longer added to small toys and other small articles (a pacifier, for example) that can easily fit inside the mouth of a baby or toddler.

                So, inflatables for older children and for adults should be exempt: DINP or DIDP can still be used.

                I think that, if you were to compromise and settle for DINP, you would not be disappointed: I was told by a PVC raincoat manufacturer that, when they did a side-by-side comparison of a sample of PVC sheet softened with DOP and a sample of PVC sheet softened with DINP, there was not much noticeable difference between them: both were very soft and 'gummy'. Both were very squeaky.
                Last edited by PVC Vinyl Enthusiast; 07-08-2023, 10:58.
                Enjoy soft, shiny and smooth PVC (inflatables and clothing). The 6P-free/10P-free material is total rubbish.

                Comment

                • Big Thud Joe
                  Senior Member
                  • May 2017
                  • 407

                  #9
                  Re: Progress update on custom inflates

                  All good, I've posted the info to your previous reply to my sourcing agent in Hong Kong, and have noted that I'm also willing to look into DINP.

                  I was rather taken back that the DEHP DOP ban has effected all the manufacturers in China, as we only could find one factory, and even then they didn't know the exact percentages.

                  As you say if DINP is good, I highly suspect that was the phthalate used for the 48 inch black and white beach balls from beachballs.com in the late 2010's. I really wished I had a chance to try one out properly, but the leaks were so bad that they were already deflating when the ball was only about two thirds full. I've kept them for templates, should any reverse engineering is to be required.

                  Comment

                  • Big Thud Joe
                    Senior Member
                    • May 2017
                    • 407

                    #10
                    Re: Progress update on custom inflates

                    So to simplify things, If I told the supplier/manufacturer/factory that I want a PVC Softness of 65 to 70 PE / PHR, with a Thickness of 200 to 250 Microns (0.20 to 0.25mm) using DINP, I should be pretty much on the right track?

                    Just trying to keep things easier for communication; the chinese admins I'm talking to have a pretty good command of english, but half the time you don't know what's being translated or not.

                    Comment

                    • PVC Vinyl Enthusiast
                      PVC Fetish
                      • Jan 2013
                      • 197

                      #11
                      Re: Progress update on custom inflates

                      Originally posted by Big Thud Joe
                      So to simplify things, If I told the supplier/manufacturer/factory that I want a PVC Softness of 65 to 70 PE / PHR, with a Thickness of 200 to 250 Microns (0.20 to 0.25mm) using DINP, I should be pretty much on the right track?

                      Just trying to keep things easier for communication; the chinese admins I'm talking to have a pretty good command of english, but half the time you don't know what's being translated or not.
                      Thinking about it, I'd say that you should opt for PVC a little thicker, to provide strength to the very soft (65 to 70 PHR) PVC. So, I'd say 350 microns. That way, the PVC will still be very soft to the touch, but the little extra thickness will ensure structural strength once the inflatable is inflated.

                      65-70 PHR (or PE) and 200 microns thickness is great for PVC raincoats (this is the material spec. of the PVC raincoats I own; watch the video), but bear in mind that PVC clothing does not have to bear any internal pressurization (an inflatable obviously does, though). So, 350 microns would be better.

                      Squeaky & Very Soft Glass Clear Blue PVC; Thickness: 200 Microns; Plasticizer: DINP; Softness: 70 PHR (or PE): https://www.youtube.com/watch?v=WTBVh7M5ZLI
                      Last edited by PVC Vinyl Enthusiast; 08-08-2023, 15:09.
                      Enjoy soft, shiny and smooth PVC (inflatables and clothing). The 6P-free/10P-free material is total rubbish.

                      Comment

                      • PVC Vinyl Enthusiast
                        PVC Fetish
                        • Jan 2013
                        • 197

                        #12
                        Re: Progress update on custom inflates

                        Originally posted by Big Thud Joe
                        So to simplify things, If I told the supplier/manufacturer/factory that I want a PVC Softness of 65 to 70 PE / PHR, with a Thickness of 200 to 250 Microns (0.20 to 0.25mm) using DINP, I should be pretty much on the right track?

                        Just trying to keep things easier for communication; the chinese admins I'm talking to have a pretty good command of english, but half the time you don't know what's being translated or not.
                        Hey, Big Thud:

                        Enclosed is a video of a 1990s-early 2000s inflatable I acquired recently. Uninflated, but the video may be helpful in helping you to source the PVC material with the desired qualities/properties.

                        This inflatable definitely contains a phthalate of some sort (most probably DINP, considering that the Low Molecular Weight Phthalate, DOP/DEHP, was phased out in the 1980s).

                        As you can see, the PVC material of this 1990s/early 2000s inflatable makes a nice 'rustle' and 'squeak', and the material is 'sticky'- sort of like how clingfilm adheres to itself; the technical term used by the plastics film/sheet industry is referred to as Blocking.

                        The PVC feels very soft, smooth and rubbery almost 'gummy', for want of a better description.

                        Thickness-wise, I'd say it is around 350 Microns. Definitely thicker than 200 Microns, but definitely thinner than 500 Microns.

                        Video: https://www.youtube.com/watch?v=rwOZcLoR9N4
                        Enjoy soft, shiny and smooth PVC (inflatables and clothing). The 6P-free/10P-free material is total rubbish.

                        Comment

                        • Big Thud Joe
                          Senior Member
                          • May 2017
                          • 407

                          #13
                          Re: Progress update on custom inflates

                          I understand what you guys are saying, but the agent is still asking me for an actual percentage which I can't seem to find any info about. Googling took me to a list of long winded papers that didn't really give any of the appropriate info. So I'm surmising they are asking how much phthalate (percentage wise) will be making up the PVC. Without this info, can't seem to move forward. Noone wants to share any datasheets, which is making this somewhat difficult.

                          Comment

                          • Big Thud Joe
                            Senior Member
                            • May 2017
                            • 407

                            #14
                            Re: Progress update on custom inflates

                            Sorry to say that the sound in the above two videos is very difficult to hear, almost like super, super low bitrate compression.

                            I've sent them this video for demonstrating the differences between 6p and non 6p PVCs.



                            I've also emailed PVC U like explaining the difficulties I'm having in obtaining datasheets and percentages.

                            Comment

                            • Big Thud Joe
                              Senior Member
                              • May 2017
                              • 407

                              #15
                              Re: Progress update on custom inflates

                              Well, this is becoming more complex as I drill further into this exercise, as upon my research I'm finding that they are five separate processes to this whole venture.

                              a) Need a toy designer developer to make the initial master design of my inflatable, from the other various inflatables I've got. Something like making 3D scans of my existing inflatables to then making the new image with the 3D graphic program.

                              Rang up several potential prospects who could do this work in Sydney and Australia generally, but this work was either outside of their scope of expertise, or were rather grumpy at the prospect of trying such a project. It seems every 3D designer in Sydney either designs buildings, office complexes, street-scapes, furniture, or industrial equipment. Can't believe there is not a toy designer/developer/prototyper in Australia's biggest city. There general concern was that inflatables are an "organic" object, thus would be very difficult to 3D scan. I told them that I do have several sacrificial samples, and that one could be inflated at a high pressure temporarily for the scan, but the attitudes I got were rather uncooperative.

                              b) Without being able to obtain any datasheets from anyone, I'll have to send a sample of one of my inflatables to a place down in Victoria, who will then create a datasheet from the PVC I supply. I've got plenty of sacrificial inflatables so this is no problem. Problem is they charge AU$6,250 per sample. If this is the actual cost, then it is what it is. I've noted it down, and it will be considered when accounting for when encompassing the entire budget of the project. I spoke to my Hong Kong agent, and said that he "may" be able to find a cheaper option.

                              c) From when I get the appropriate datasheets containing the relevant info to the desired PVC, they will then be supplied to a factory for manufacturing of the desired raw sheeting. I did contact the above suggested proprietor, but aside from pretty much replying with information that I already new, he was of the opinion that he did not wish to divulge any further information regarding any manufacturers. Upon asking if I could at least get some info on datasheets, this request was ignored, so surmising this was the info he did not wish to share, I smell a middle man. (this would have really helped by a long way if I got this cooperation, but at this stage the lack of this info remains to be the main obstruction to moving forward.

                              d) The master (in whatever form) that would be created in step a), and the sheeting fabricated in step c) would have been supplied to the manufacturing factory who would be making the lifesize character. A physical prototype of the character would have been made using other PVC, (not for wasting my custom PVC). They would most probably be a number of samples being sent out (preferably as few as possible) for any minor corrections.

                              e) then final manufacturing using the PVC from Step C, when then I would see my dream lifesize inflatable character become reality, and with everything finalized, get a few hundred made.

                              My ultimate grumble is that I know that they are places and agencies that could bring all this together, and give me a final cost before going ahead with this, but I'm NOT finding these agencies or places. I don't want to commit to anything until I know all the final costs of the entire project. I don't want to be working through the first two steps to realise that the entire budget has been used, and that nothing has materialized out of the process. There is one firm in Melbourne who are capable of doing this, but have stated that they don't want to know about it, because the job is too small.

                              So in light of the difficulties I'm facing, in the best efforts of moving forward, I'll be asking my hong kong agent on further advice on a plastics analysis service that can give better value. Problem is they seem to have is what could be best described as a "step by step" approach, without any real fourth sight on encompassing the entire scope of a project.

                              End of rant.
                              Last edited by Big Thud Joe; 11-09-2023, 03:52.

                              Comment

                              Working...