repair/reinforcement first attempt

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • heaviest
    Senior Member
    • Jun 2018
    • 914

    repair/reinforcement first attempt

    I had a 36 inch Intex tire tube with a tiny hole in the inner seam that I tried to repair with vinyl cement. Just ran a ribbon of the stuff along the seam. I did the whole seam, just because. I saw a you tube video of someone reinforcing seams this way so I figured if I managed to plug the hole I wanted the whole seam reinforced.

    And while I had the cement out, I also did a 36 inch Intex clear-top tube with a slightly bigger hole in the inner seam. This one had a fatter pinch seam that would have required both sides done rather than one ribbon over the top, and I was tired of vinyl cement by this time, so I just repaired the hole.

    And the results...

    Overnight the clear-top tube lost a little bit of air, and the tire tube lost more than that. Failure?

    I fully inflated the clear top tube and a 205 pound woman sat on it and it just popped. But...the part I had patched held! Tore right next to it, though. I figure I hadn't managed to plug the hole, but as reinforcement, the vinyl cement might have worked.

    And so I resolved that the less successful tire tube would just pop. Fully inflated it and 205 pound woman sat on it...and it held! Sat opposite the hole, expecting it to pop, but it didn't. Overinflated the thing and she sat on it...and it held. Overinflated it quite a lot, and it still held.

    Not sure where it's even still leaking. I think I might feel a tiny leak at the site of the hole repair, but it's so slight I can't tell if I'm imagining it. Perhaps it's leaking from somewhere else, too.

    But the tire tube I consider a success, if I can just find the leak. I've given the whole seam another run, with special attention around the original leak. But maybe there's a pin hole leak somewhere not on the seam.
  • heaviest
    Senior Member
    • Jun 2018
    • 914

    #2
    Re: repair/reinforcement first attempt

    Success!

    The tire ring started today's fun at about 29 inches around measured with a sewing tape. When first inflated it's about 28 inches, but the thing is soft enough that just keeping it fully inflated stretches it, so I added another inch, to 30 inches, just keeping it inflated.

    With my second vinyl cementing having set for hours, we loaded 205 pound woman opposite the hole I patched, which is just about under the valve on the inner seam. We had to add air about three times to keep her from bottoming out. I added 75 pounds of weights to her lap, and we added more air to keep her floating. It held 280 pounds just fine, having added quite a lot of air.

    My partner currently weighs 455 pounds. She got on it and bottomed out almost immediately. More air...and more air. It took quite a bit to keep her floating. But it holds! 455 pounds, unevenly loaded, and it didn't pop!

    In its current state of inflation, and having rested for a while, it is currently 30 1/2 inches around where she was sitting, where it is smallest, and 36 inches around where the valve is, where it is largest. To float 455 pounds off the floor without bottoming out, it is overinflated enough that there's almost no pucker on the outer seam, even now while it is unloaded. While she was on it, it bulged up to 42 1/4 inches, a 50% stretch and 125% increase in volume.

    On the underside, the "rim" part of the tire print has grown by a lot, so the tire looks twisted. It exaggerates the size difference of the two sides. Very cool.

    I'm gonna call the vinyl cement inner seam trick a great success.
    Last edited by heaviest; 07-09-2020, 21:32.

    Comment

    • heaviest
      Senior Member
      • Jun 2018
      • 914

      #3
      Re: repair/reinforcement first attempt

      Added even more air and she still bottoms out after a couple minutes. We got the unloaded side to bulge to 44 3/4 inches, a 60% stretch and 156% increase in volume.

      Unloaded it's 31 inches on the small side and 39 inches on the stretched side, and the tire graphic is looked quite distorted.

      ETA 45 1/4 inches and it's the outer seam that failed. About 1/2 inch hole. I'll try to repair it, but this tube just isn't up to 450 pounds.

      ETA after another repair and hours of recovery under no stress, the tube is now lightly inflated and 28 inches around on the small side and 30 1/2 inches on the large side, and most of the distortion in the tire print design has gone away. It's mostly recovered, just a little bit of stretch left. I really like this thing, so I hope the repair holds. The outer seam is now reinforced and curing. It's difficult to get a smooth band of cement on the puckered outer seam, so I hope the cement remains flexible.
      Last edited by heaviest; 08-09-2020, 04:30.

      Comment

      • heaviest
        Senior Member
        • Jun 2018
        • 914

        #4
        Re: repair/reinforcement first attempt

        With the outer seam patched and half the outer seam reinforced, the side we let expand, we got the thing to bulge to 46 3/4 inches, a 67% stretch, and with that much overinflation it took her 5 minutes to bottom out, so we are getting close to finding the maximum stretch with 455 pounds. She even did a tiny bit of bouncing. A few minutes after getting off it, it is 30 1/2 inches on the small side and 41 inches on the large side.

        It gets soft overnight so there's still a leak but I've checked the reinforced parts of the seam and can't find it. Perhaps there's a pin hole in it somewhere. Can't find that, either. The leak is slow enough that it doesn't affect play.
        Last edited by heaviest; 08-09-2020, 13:37.

        Comment

        • heaviest
          Senior Member
          • Jun 2018
          • 914

          #5
          Re: repair/reinforcement first attempt

          That was the long way of saying that reinforcing seams with vinyl cement works. And, surprisingly, it's necessary to do the outer seam of a swim ring.

          Comment

          Working...