How Much Pressure Is in a Pool Toy?

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • heaviest
    Senior Member
    • Jun 2018
    • 914

    How Much Pressure Is in a Pool Toy?

    Some time ago I made a post where I wanted to do this. I asked if anyone knew what I'd need to measure the pressure in an inflatable. Here, someone went through the same query. He found online, as I did, conflicting information, and he had to kinda guess, like I did, what range pressure gauge to get. He chose the same one I did, 3 psi.

    Here he describes his research and gauge, while his focus was on balloons.



    Here's the testing on inflatables.



    I wanted to see how tightly I had to inflate, say, an air mattress, to simulate having an 800 pound woman on it with me. I found it wasn't that simple. For one, overinflation stresses it more than weight alone does. I found that the effect of adding weight varies with how much pressure there already is. So, I found a pressure for a particular air mattress (a one-chamber 18-pocket mattress, the kind with an inline pillow rather than pillow on top), inflated a little more than most people would, and then loaded with me (480-ish pounds at the time) plus 800 pounds. It was about 1.9 PSI, if I recall. Then the objective was to overinflate it enough that I could achieve 1.9 psi with me on it but without the 800 pounds. It was something like 1.7 psi. That is, adding 480 pounds to 1.7 psi gave me 1.9 psi. Like, my weight hardly mattered. I could achieve the same thing just inflating it a little more.

    Laying on an overinflated air mattress is exciting. It gives me that anticipation of a pop. It makes me wonder how the thing doesn't just burst. It makes boomy noises as my skin binds on it. All the things I like about stressing inflatables over an extended session. I don't like easy pops and I don't like punctures. I'm all about the stress. Overinflation gives me that.

    But it's nothing like having an 800 pound woman on it with me. That is intangibly more exciting. Like, it would be abusing the inflatable doing this with two normal sized people, and we're abusing it way more than that. I'm not sure what exactly it is that is exciting about that. But for some reason, it's not the same with overinflation.

    But back to measuring pressure, and what I think is happening with sitting on inflatables...

    WHen you sit on an inflatable, you decrease its volume, which increases the pressure, which...increases its volume. As the vinyl stretches, you reach a new equilibrium. The pressure you achieve is always just less than the pressure it takes to stretch the vinyl. It will stop stretching when you achieve that volume. So, you add air and start the process again.

    If you do this a lot you've probably discovered that there is a point where you are only stretching it a little bit. You get off it and it's soft, but it recovers quickly.

    When you stretch the vinyl it has a memory and wants to go back, so it recovers. That's the temporary stretch. But if you've overloaded it, there's also some permanent stretch.

    I wanted to measure all this, but I found that it just varies too much. There's such a small difference between enough pressure to permanently stretch an inflatable and enough pressure for a runaway stretch, that you can't measure it reliably. And it varies from toy to toy. By a lot.

    I've found that the largest chamber stretches the most. When you lay on a one-chamber air mattress, the pillow stretches the most. It's partly because you displace air there, but at high pressure that doesn't really matter. What's really happening is the largest chamber, by circumference, is stretching the most. That'd be the pillow. The guy in this video found the same thing, testing different size toys. And if you get a two-chamber air mattress, youll find you can't get a runaway stretch in the tube end no matter how much pressure you put it under. It will just leak before it grows substantially. Because those are small-circumference chambers.

    I could go on and on about sitting on one side of a swim ring, baffles limiting chamber size, etc, but likely nobody cares as much as I do. But those 18-pocket air mattresses? They hold a ridiculous amount of weight, and support high-pressure, because those pockets limit the size of the main chamber. The baffles in the pillow do the same thing. The baffles in all inflatables do that.

    Whales don't have interior baffles, so they won't take a lot of pressure. Bigger beach balls are easier to blow pop than smaller ones, despite being made of thicker vinyl. It's the chamber size. Vinyl wants to stretch laterally. A tighter round takes more pressure.
    Last edited by heaviest; 16-11-2024, 15:28.
  • Bass Boll
    Senior Member
    • Jun 2023
    • 211

    #2
    Thank you for your research report, heaviest! Your pressure of 1.9 psi = 0.13 bar is indeed very much for inflatables although you may have the 20-fold pressure in your car tyres. I compared to the test pressure required by the technical rule ISO 25649-3 “Floating leisure articles for use on and in the water - Part 3: Additional specific safety requirements and test methods for Class A devices” which is a common standard for inflatable rafts, swim rings and the like. If no explicit working pressure is given by the manufacturer (and that's hardly the case for any toy on the market), a pressure of 0.06 bar = 0.87 psi shall be repeatedly applied and no leakage shall be observed. So you produced practically twice the pressure to be tolerated!

    Comment

    • cl23
      Senior Member
      • May 2022
      • 381

      #3
      Originally posted by Bass Boll
      a pressure of 0.06 bar = 0.87 psi shall be repeatedly applied and no leakage shall be observed. So you produced practically twice the pressure to be tolerated!
      That is absolutely no good idea with larger inflatables, if you do not want to pop or damage them. Even an intex Orca gets tight at 0.04 bar. More gets it really tight.
      The larger the inflatable, the less pressure it will survive.

      Comment

      • Bass Boll
        Senior Member
        • Jun 2023
        • 211

        #4
        The 0.06 bar test are a couple of test cycles over a few minutes each under lab conditions. That means no extra load or test person mounting the toy (this is a separate test), no additional sunshine heat-stretching. Of course an Intex Orca produced according to ISO 25649-3 may not survive a day on the beach pumped to that pressure, let alone a humping session! The test shall probably just mimick the stress of "normal" use over several days within half an hour. Finally it highlights the extent of the overpressures heaviest is dealing with...

        Comment

        • heaviest
          Senior Member
          • Jun 2018
          • 914

          #5
          Here are some more observations, but remember that key to predicting the robustness of an inflatable is that larger chambers stretch more than smaller chambers, small outer curves stretch less than large outer curves, and inner curves are less sturdy than outer curves. Inner baffles limit how large a chamber can stretch, if the baffles themselves don't break.

          I've found that regular shapes are sturdier than irregular shapes. Probably has to do with inner curves (weak points), but also, baffles that shape a toy make for uneven stress points. The pockets in my favorite 18-pocket mattresses are closer together in one direction than the other, so if you look at how the vinyl bulges around them, you can see it is tighter in one direction than the other, and bulges more in one direction than the other. The parts that feel the most stressed generally ARE the most stressed.

          I've found that inflatables will take a LOT of weight for a short time, but leave them overinflated for a long time, even unloaded, and they'll develop leaks. When I get off a toy and it feels soft, if I just put it away, it will contract and get tight and those inner curves will be stressed all night long. If a swim ring manages to survive a session of adding air repeatedly as it stretches, and I just stand it aside, I can admire how much larger it is than an unstretched ring, but it will contract, and if I come back in a couple hours it'll be really hard. And if I put it away like that it'll develop a leak. I have to release air as it shrinks.

          I've found that unevenly loading an inflatable stresses it more, which seems obvious. But those 18-pocket mattresses usually spring a leak in a pocket that isn't being sat on.

          Movement stresses a toy a lot. I've been on a mattress with a 700 pound woman for an hour, and within a minute of her rocking, because she's bored, it'll spring a leak.

          There's a large element of random chance. I had a kid-size overnight kind of mattress used as a bench cushion for a 700 pound woman. She used it for an hour or several hours at a time for a week ore more, and the first time I laid on it for a couple hours it leaked. I've had swim rings take 700 pounds and I've had them pop with 200.

          Inflatables made for two or more people are made of vinyl that is thick enough that you don't generally get a runaway stretch with just the weight of people, even extremely large people, even a pile-on of extremely large people. It takes a compressor to achieve enough pressure to stretch that vinyl. Or heat. These inflatables are most likely just going to develop a leak. But an inflatable with a large, un-baffled chamber will stretch and burst.

          Those single-chamber, slim air mattresses? Those will reliably hold 600 pounds without a runaway stretch, at room temperature, out of the sun. I know because I used to be that size and I laid on those things A LOT. I've also put as much as 1400 pounds on them, and the pillow will grow ridiculously for ten minutes and then explode. The point of too much weight is somewhere in between those numbers. With just 600 pounds, though, they'll eventually leak, almost always from the seam at the top of the pillow, or the seam between the pillow and mattress, but the pillow won't just keep growing. When you see that happen, there was sun involved. I've had these mattresses spring fast leaks at 600 pounds, but I've outright popped one just a couple times. They usually spring a slow leak.

          Those 18-pocket mattresses are my favorites because the unevenness of the stress on the tops of those pockets just seem like the thing is about to burst. If I can get a couple hours of high stress out of those things and then put it away undamaged it feels like a real accomplishment. But if it does spring a leak around one of those pockets, it repairs pretty easily with vinyl cement. You get leaks on the tops of those pockets about five times as often as the bottom. Eventually you'll get a leak too big to repair, but I've gotten six or eight holes repaired on some mattresses before I have to give up on them. If one of the pockets catastrophically fails, the pop isn't as impressive as you'd hope.

          The 18-pocket mattresses that are all one chamber, with the inline pillow that is not a separate chamber, provide some place for the air to go when you load the mattress. The pillow with its baffles will take quite a lot of weight. But breaking one of those baffles is a real charge. I've described some sessions on these mattresses in the air mattresses thread.

          Someone once posted a picture of a woman laying on one of these mattresses overinflated, and I observed that she could get several of her friends on there with her for a few minutes and it would probably survive, but if she lays on it by herself all day long it will probably develop a leak. As I said, inflatables will take a lot of weight for a short duration, even overinflated, but they won't take a long-term overinflation.

          I've described 700 pounds or more on beach balls and swim rings in other threads. You know how when you bounce on a beach ball one panel will get a runaway stretch? It takes a ridiculous amount of weight to do that with weight alone, without bouncing.

          I wanted to put numbers to all of this, but the pressure an inflatable takes is highly dependent on how big its largest chamber is, and its shape, and a large element of random chance. But also time under pressure. Too many variables. The closest I've come to repeatable experiments is with those single-chamber slim mattresses. With well over 1000 pounds, static, on the tubes and not on the pillow, those things will pretty reliably have a runaway stretch in the pillow and explode catastrophically rather than developing a slow leak. Unfortunately, Intex doesn't make the transparent mats anymore. The economats will do the same thing but they aren't as robust. I have a lot less experience with them. But an economat pillow that is super stretched looks really cool. It gets streaks and splotches and is a little transparent.

          Last edited by heaviest; 18-11-2024, 12:03.

          Comment

          Working...