So I was looking for some "interesting" inflate to heatstretch (because bigger is better!) but I'm fairly limited on space and while mindlesly browsing I remembered inflatable fashion mannequins.
I have tried these before, with ... varying ... degrees of success; they are built fairly sturdy, but they have A LOT of not very well finished seams which have a nasty habit of splitting/leaking.
Not wanting to go through a huge reinforcing program I decided to buy some torso mannequins instead of full ones after the problem I had with those and the results were ... fun.
The only thing I will recommend if you want to use these for anything: reinforce the waist seam with pvc glue first. It is typically the first to fail. Adding "branches" where seams attach to it is also recommended; don't have to be real long, about 5-6cm (2-2.5") i uually enough to prevent most problems. You can go full seam reinforce of course, but that's a lot of seam to cover.
Process used:
Aeration pump at 70 litres/minute, and a hot shower. I am VERY reluctant to use boiling water (as I've noted before) since I had some close scrapes with it before.
Wait for it to inflate tight, spray with hot shower. If you want more localized stretch, hold that area under a running (hot) tap.
First set of 3 photo's is about 30 minutes into the process. Advantage of the slow pump is I can keep it running throughout, don't have to stop. An unstretched mannequin is in both sets for comparison.
Second set (of two, forgot there's a limit of 5 attachments, just did front/side) is another 15 minutes later, after the chest baffle inside decided to blow out. I did go too far and despite my reinforcing previously, a panel tore along a waist seam right next to the reinforcement and that wass trhe end of it.
Lessons learned: more waist reinforcement (I'm thinking getting some pvc tape and gluing it over the seam all the way around for extra strength), less enthusiasm when you know you're at/near the limits.
Fortunately these are fairly cheap so a failure isn't the end of the world, but it sucks to see a few hours of reinforcing/stretching get lost.
I have tried these before, with ... varying ... degrees of success; they are built fairly sturdy, but they have A LOT of not very well finished seams which have a nasty habit of splitting/leaking.
Not wanting to go through a huge reinforcing program I decided to buy some torso mannequins instead of full ones after the problem I had with those and the results were ... fun.
The only thing I will recommend if you want to use these for anything: reinforce the waist seam with pvc glue first. It is typically the first to fail. Adding "branches" where seams attach to it is also recommended; don't have to be real long, about 5-6cm (2-2.5") i uually enough to prevent most problems. You can go full seam reinforce of course, but that's a lot of seam to cover.
Process used:
Aeration pump at 70 litres/minute, and a hot shower. I am VERY reluctant to use boiling water (as I've noted before) since I had some close scrapes with it before.
Wait for it to inflate tight, spray with hot shower. If you want more localized stretch, hold that area under a running (hot) tap.
First set of 3 photo's is about 30 minutes into the process. Advantage of the slow pump is I can keep it running throughout, don't have to stop. An unstretched mannequin is in both sets for comparison.
Second set (of two, forgot there's a limit of 5 attachments, just did front/side) is another 15 minutes later, after the chest baffle inside decided to blow out. I did go too far and despite my reinforcing previously, a panel tore along a waist seam right next to the reinforcement and that wass trhe end of it.
Lessons learned: more waist reinforcement (I'm thinking getting some pvc tape and gluing it over the seam all the way around for extra strength), less enthusiasm when you know you're at/near the limits.
Fortunately these are fairly cheap so a failure isn't the end of the world, but it sucks to see a few hours of reinforcing/stretching get lost.
Comment