DIY - High power portable inflator thingy

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Jup
    DIY balloon tools
    • Aug 2021
    • 43

    DIY - High power portable inflator thingy

    I like building my own DIY inflators and have been working on something that feels cool enough to share.
    Found a fan on Aliexpress (click for youtube vid showing it) and instantly decided it was going to be the core of my new balloon inflator.

    The only obstacle so far are Will's (59balloons) fresh tripple dipped balloons. I need to stretch the neck while blasting full power to start inflation but after that the bulb inflates no problem!

    Here is the prototype device itself... would not try to fly with it at this stage for sure. Q16 for scale.

    Black shroud at the back is to avoid things being sucked in. It can be 20% shorter. Also have the narrowest attachment on it here so this is the longest it can be.
    Linear potentiometer to control the speed controller. 4S lipo for the power (Calculated at 2 minute max power runtime).

    Downside of this design is the requirement of a LiPo, not a fan of storing and charging those indoors personally.
    It should draw 400-430w at full blast so this is about the only option.
    inflator smaller.jpg

    As its an ESP32 controlling this I should be able to program inflation routines for specific balloons, and even trigger them remotely using WiFi. Excited to use that for videoing some pump to pops in the future.
    Last edited by Jup; 22-07-2026, 18:42.
  • Graham'sTrumpet
    Member
    • Nov 2022
    • 38

    #2
    Would love a component list and schematic, I've been passively planning to build something very similar myself for a while.

    Comment

    • Jup
      DIY balloon tools
      • Aug 2021
      • 43

      #3
      I can give a general idea of what to buy at the end for sure, but its all off the shelf parts as far as electronics go Schematic might be fun to make yeah.

      Comment

      • TheMole
        Senior Member
        • Nov 2019
        • 302

        #4
        That looks diabolical and I love it. Seems powerful just like the Metrovac I usually use but the portability is amazing.

        Comment

        • Thinskinned
          Look Out!
          • Jul 2024
          • 247

          #5
          i love the idea of a linear potentiometer as a switch, dialing the power just high enough to inflate the balloon just a liiitttttlllleeee more.

          Comment

          • Jup
            DIY balloon tools
            • Aug 2021
            • 43

            #6
            Originally posted by Thinskinned
            i love the idea of a linear potentiometer as a switch, dialing the power just high enough to inflate the balloon just a liiitttttlllleeee more.
            Also fun when I dial the speed just right so it just overpowers the inside pressure, but not enough to actually really inflate it. Supertight balloons that last a while but can go any moment 💨🎈. Wonder if I can combine that with a pressure sensor inside the balloon 🤔

            Comment

            • cl23
              Senior Member
              • May 2022
              • 381

              #7
              Originally posted by Jup
              Wonder if I can combine that with a pressure sensor inside the balloon 🤔
              This works for sure. I've built three programmable electronic inflators with pressure (and other) sensors for making the tightest possible balloons automatically. I did not put a sensor or something else into the balloon, but measured from the blower side. Be aware, that the air flow has a major impact on pressure sensor readings, if the sensor is situated in the airflow. I had to compensate for this on software side and integrated an automatic calibration.

              If you want to measure the pressure inside the balloon, you can use a differential pressure sensor with one or two hose connectors. Put a hose on one of the connectors and put the hose into the balloon, that you want to inflate. Use the thinnest hose, that you can get or put something into the other end of the hose to minimize airflow, that can go to the sensor for most stable readings.

              I like the very small footprint and portability of your device and am looking forward to the further development of it

              Comment

              • Jup
                DIY balloon tools
                • Aug 2021
                • 43

                #8
                Originally posted by cl23


                I like the very small footprint and portability of your device and am looking forward to the further development of it
                Currently working some stupid hours so its been delayed for at least a month sadly, slowly working on my 3d modelling skills to make this happen though! I did experiment with the pressure sensor using a BMP388 I had laying around but the battery and stuff was too large to actually test in normal sized balloons. This would avoid part of the high speed air pressure stuff and measure deeper in the balloon.

                Comment

                Working...