So I'm a semi-popper, but something that's been a bit of a hangup in general is worrying about balloons popping while inflating due to defects/weakening from previous inflations. I believe this to be related to anxiety, so there's a possibility my concerns are irrational. I'm more comfortable inflating with a fast pump because it's really fast and I don't have time to think before the balloon is starting to neck out a bit, but I'd like to be more comfortable (or, if not, at least knowledgeable) blowing them up by mouth as well -- I enjoy that so much more.
I have no issues blowing up just about any balloon nearly to rated size, but I start to get scared before the neck even comes out a little. I know that there's a lot more room in the balloon because the pump will go right past that point quick as you like, but I'm worried about defects causing the balloon to pop prematurely right next to my face.
Of note: I'm just using retail balloons, none of the purpose-made looner balloons -- I assume the large cattexes etc have great QC and there's less to worry about?
With that said, a few series of Material Science/Physics questions that I hope you all will have the answers for:
1) What are the most common defects? How common are they? When will they cause a balloon to catastrophically fail -- during inflation, overinflation, or handling/riding/bouncing?
2 ) I had a few crystal 11" uniques, one had what looked like a round "clear" spot on a colored balloon right where the drip point should have been, is lack of color fine, or was the latex thinner there? it was already a little overinflated and tied off before I noticed it, so even if it is a defect is it something to be concerned about?
3) Another of the uniques, I guess it was burgundy? Right when you start to inflate there's these white lines crisscrossing the surface of the balloon. is that just talc or is there something that happens to latex that causes it to do that? if so, is it bad?
4) does inflating the same balloon over and over make it more likely to pop during inflation? I know about hysteresis and that the balloon will get bigger and bigger on subsequent inflations, but does that make it weaker while being inflated? how long can they be reused for? will defects that did not cause the balloon to pop on first inflation cause pops on re-inflations?
5) if a balloon is already used and stretched out, is it necessary to stretch it by hand prior to re-inflation? I always do and I think I tore a hole in one of my TT17s doing that, so maybe it's not necessary/actually a bad idea?
6) Am I being irrational? Are balloons popping during inflation something to be concerned about in 2024? (sorry, this isn't really a material science question)
I have no issues blowing up just about any balloon nearly to rated size, but I start to get scared before the neck even comes out a little. I know that there's a lot more room in the balloon because the pump will go right past that point quick as you like, but I'm worried about defects causing the balloon to pop prematurely right next to my face.
Of note: I'm just using retail balloons, none of the purpose-made looner balloons -- I assume the large cattexes etc have great QC and there's less to worry about?
With that said, a few series of Material Science/Physics questions that I hope you all will have the answers for:
1) What are the most common defects? How common are they? When will they cause a balloon to catastrophically fail -- during inflation, overinflation, or handling/riding/bouncing?
2 ) I had a few crystal 11" uniques, one had what looked like a round "clear" spot on a colored balloon right where the drip point should have been, is lack of color fine, or was the latex thinner there? it was already a little overinflated and tied off before I noticed it, so even if it is a defect is it something to be concerned about?
3) Another of the uniques, I guess it was burgundy? Right when you start to inflate there's these white lines crisscrossing the surface of the balloon. is that just talc or is there something that happens to latex that causes it to do that? if so, is it bad?
4) does inflating the same balloon over and over make it more likely to pop during inflation? I know about hysteresis and that the balloon will get bigger and bigger on subsequent inflations, but does that make it weaker while being inflated? how long can they be reused for? will defects that did not cause the balloon to pop on first inflation cause pops on re-inflations?
5) if a balloon is already used and stretched out, is it necessary to stretch it by hand prior to re-inflation? I always do and I think I tore a hole in one of my TT17s doing that, so maybe it's not necessary/actually a bad idea?
6) Am I being irrational? Are balloons popping during inflation something to be concerned about in 2024? (sorry, this isn't really a material science question)
Comment