Cordless inflaters

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Geoff Robinson
    Senior
    • Mar 2024
    • 131

    #16
    What you need is the normal mains operated electric balloon pump.

    A mains inverter 12v Dc to 230 110 v Ac
    at least 500w.

    12v 8ah battery maybe 2 batteries.

    Comment

    • homerthompson233
      Junior Member
      • Dec 2025
      • 8

      #17
      I would not recommend pumps like Xiaomi Air Compressor 1s or similar. I have one Xiaomi and it blows balloons veeeery slow.

      Comment

      • Golden
        I'm whatca need
        • Jun 2022
        • 483

        #18
        try this



        I have it pretty good.
        my lament of longing
        This is now my only choice
        My shadowed heart is lonely
        I can't seem to find my voice
        ​

        Comment

        • Guest

          #19
          The Makita DAS180 is good but the soft/delayed start is bit annoying and it makes it difficult to fine tune the level of inflation in the way that you would with a regular balloon pump.

          The Ryobi inflator has been redesigned and the new model is more powerful and much quieter (it's part of the whisper range). The old model was RVI18 and the new one is PCL016B.

          I have the new one on order and I'm hoping that it will be awesome. The maximum pressure in the specifications is rather low, but there are reports of other people using it with balloons successfully.

          Comment

          • Guest

            #20
            In case anyone is interested...

            The new version of the Ryobi works on Belbal 17" at least. I haven't tried any others yet.

            The air flow is fixed and slightly lower than the DAS180 on the lowest setting. The noise is about the same despite the "whisper" branding. Both are much quieter than a traditional balloon inflator, even the small Zibi. A lot of the sound is turbulance through the nozzle, and so that is further muffled when the nozzle is connected to something.

            Unlike the DAS180, the Ryobi has no soft start. If the trigger is depressed lightly, then the action is momentary, so the air stops as soon as it is released. If the trigger is depressed fully, then the inflator latches on until the trigger is pressed again.

            Comment

            • zyzz
              Member
              • Aug 2024
              • 35

              #21
              Originally posted by quirkafleeg
              In case anyone is interested...

              The new version of the Ryobi works on Belbal 17" at least. I haven't tried any others yet.

              The air flow is fixed and slightly lower than the DAS180 on the lowest setting. The noise is about the same despite the "whisper" branding. Both are much quieter than a traditional balloon inflator, even the small Zibi. A lot of the sound is turbulance through the nozzle, and so that is further muffled when the nozzle is connected to something.

              Unlike the DAS180, the Ryobi has no soft start. If the trigger is depressed lightly, then the action is momentary, so the air stops as soon as it is released. If the trigger is depressed fully, then the inflator latches on until the trigger is pressed again.
              Hi there, reviving this post to ask about the PCL016B, can it inflate a balloon from "zero", meaning, does it have enough pressure to do so? The makita has around 4 psi max pressure listed in its specs, but I can't find the same info for the PCL016B

              Comment

              • inflatedskintight
                Senior Member
                • Sep 2019
                • 124

                #22
                I don't know about the Ryobi device, but I'd like to add that I recently picked up one of the cheap "air duster" blowers from a local tool store. It looks like the one somebody posted earlier in this thread and it's USB rechargeable. I'm really impressed with it. It's pretty quiet, much quieter than a full-size balloon pump, and it will easily start a 12" metallic balloon and blow it to pop, which is a pretty tough test. It also has enough volume to blow up my big unicorns quickly. The way it switches on and off is a bit annoying: one press of the button switches it on at full power, which is great, but it takes 3 or 4 presses to step through the lower power settings (which aren't much use for inflation) to switch it off again.

                Comment

                • Gunnapop
                  Senior Member
                  • Oct 2020
                  • 215

                  #23
                  ...check out Carlson barrel pumps. They are not cheap....but their largest model can fill a 16" in a few strokes. I have one and swear by it. ~gp

                  Comment

                  • Guest

                    #24
                    Originally posted by zyzz

                    Hi there, reviving this post to ask about the PCL016B, can it inflate a balloon from "zero", meaning, does it have enough pressure to do so? The makita has around 4 psi max pressure listed in its specs, but I can't find the same info for the PCL016B
                    The Makita is much more powerful. The Ryobi can struggle to get balloons started if they are very thick and fresh. Sometimes they will start to inflate if you stretch the neck while the balloon is on the pump but I found a few that wouldn't inflate at all.

                    Comment

                    • Markus_Looner
                      Member
                      • Apr 2024
                      • 59

                      #25
                      I have been rocking this 18v AEG workshop blower for years. It only really struggles with thick little 12" loons, everything else stands no chance. Will pump to pop almost anything latex you put on it. Comes with the nozzle with two different sizes one specifically designed for the valves on inflates. It can inflate a 5ft beachball in under 2 minutes
                      You do not have permission to view this gallery.
                      This gallery has 1 photos.

                      Comment

                      • Thinskinned
                        Look Out!
                        • Jul 2024
                        • 247

                        #26
                        I have accumulated quite the collection of cordless blowers, I now have in addition to the Makita DAS180, I have a KICA Jetfan 2 Max and a cordless from Amazon that looks kinda like a handpump but works great. all 3 of them can start a balloon from zero, I know the makita has enough power to blow them right to popping but I'm not sure about the other two. I suppose someday I'll find out. I have confidence that the amazon one probably will but don't think the jetfan has quite the power, at least on 17" and smaller balloons, I know the larger the balloon, the less pressure it takes to pop.

                        I had a few of the amazon/temu specials, but they're junk and difficult to use because of the control form factor. I got the KICA because it was easy to find a 3d printing profile for the attachments so I can make custom ones.

                        Comment

                        Working...