What would be the best way for me to weaken the latex of a balloon to make it easier for hug popping or a potential spontaneous pop while inflating it? Does inflating balloons to a relatively large size several times help? How many times is ideal and how many would be too much since the latex would become too weak? I want to create more spontaneous pops while blowing them up, as I believe that could help push my comfort zone towards a more traditional blow to pop. Keep in mind I use 12 inch balloons almost exclusively.
Weakening latex for pops
Collapse
X
-
-
I would recommend inflating the balloons a few times, until the neck is inflated fully. 3-5 times is safe with BelBal balloons, but it depends on the quality and age of the balloons and how tightly you inflate them.
I would not recommend baking in an oven, you later want to use again for preparing food. Toxic fumes are released, when balloons are overheated (over about 80° C / 176 °F).
The balloons themselves get toxic as well in this process (Lots of nitrosamines are released that are a high risk for causing cancer). I tried that as well in a safe environment but would not touch these balloons without gloves. Be aware, that baking balloons absolutely works to get them to incredible sizes, but you will waste 90% before getting good results. It's trial and error and IMHO the smell is disgusting.Comment
-
All fair points, especially food safety. I use my 3d printer bed for this task personally for control and, well, I aint printing food yet.I would not recommend baking in an oven, you later want to use again for preparing food. Toxic fumes are released, when balloons are overheated (over about 80° C / 176 °F).
The balloons themselves get toxic as well in this process (Lots of nitrosamines are released that are a high risk for causing cancer). I tried that as well in a safe environment but would not touch these balloons without gloves. Be aware, that baking balloons absolutely works to get them to incredible sizes, but you will waste 90% before getting good results. It's trial and error and IMHO the smell is disgusting.


Comment
-
If you aren't too scared, blow up a balloon as big as you can, deflated it, repeat. Each time, the balloon will be more stretched out and get bigger if it doesn't pop.
The balloon will eventually pop if you keep doing this. For me, this is scarier, because even if the balloon isn't as loud, it can pop at any time.
I like to overinflate balloons and clip or half-knot them and leave them a few days or even weeks. If you blow these until they pop, they can get much bigger than a fresh balloon can. This is a really fun way to clean up after parties if you can untie a balloon.
What works for me is blowing a fresh balloon as big as I dare, then stepping on it slowly until it pops. This gives a good idea how much it can stretch and how loud it will be. Then I can blow another balloon bigger without fear because I know it will stretch more before popping.
You could try 2 or 3 inflations, tie off the balloons, then hug-pop them.
👍 1Comment
-
What you can also do is to take your inflated, knotted balloons and use a pin to puncture the neck close to the knot where the latex isn't stretched. They won't noticeably lose air that way, but once you squeeze them hard enough they will go bang. I like doing this to a bunch of balloons and then grabbing them one by one to crush them in my armpit - super satisfying, and it makes me look so strong (which I'm not
)! Much faster and easier done than baking or pre-stretching, but also kind of a cheap trick. I do it to gain control over whether a balloon is gonna pop or not when squeezed, which is the opposite of what you're going for. Maybe worth a try though.
I guess you could also do the same to get them to pop on inflation, maybe you'd even be able to control how much air they will take before giving in by varying the spot where you puncture the rubber. You could also prepare a bunch of balloons of the same size and colour that way and play a game of russian balloon roulette - when will it pop? :P🥰 1Comment
-
Baking them. Here's some advice:
A big key to successfully baking balloons is even baking, an unevenly baked balloon (part of it is thick and stiff, and the other part of it is thin and stretchy) will likely pop really early on in inflating before it even gets to a quarter of it's rated size, balloons can't seem to handle the inconsistency. I'm sure that preheating the oven, using the fan, lower temps for longer times rather than higher temps for shorter times, and having the balloons in the middle (I have them sandwiched between two pieces of baking paper on the metal rack/shelf) bakes them more evenly. I have the most success with evenly baked balloons, getting them way past their rated size and they can still handle some light abuse.
Also, with a lot of balloons the necks will be a lot thinner and stretchier than the main body, and this can be the weak link in the chain and lead to premature bursting after baking when you inflate them, so I will tuck the necks into the main bodies which protects the necks from the heat a bit and they don't get as baked, and it also makes more room for more balloons on the baking paper.
As for temps and times, it can vary a lot from brand and size of balloon. But usually for me I've found that 130c works for some balloons and 140c works for others, and usually 15 mins works for some balloons, and 20 to 23 mins works for others.Looning since 1989
To see my pictures of prints and blown up examples: Printed Balloons - Balloon and Inflatable Fetish Forum😎 1👍 1Comment
Comment