Carnival Water Gun Burst Game

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Gunnapop
    Senior Member
    • Oct 2020
    • 215

    Carnival Water Gun Burst Game

    .....just $2K (USD)...for under 24 hours...sheesh. ~gp

  • stretchedtight
    Senior Member
    • Apr 2013
    • 275

    #2
    Originally posted by Gunnapop
    .....just $2K (USD)...for under 24 hours...sheesh. ~gp

    https://airfairentertainment.com/ren...balloon-blast/
    Man I would love to have a version of this where I can use a laser pointer on a toy gun to inflate a balloon (turn a pump on and off as an example) and have a race. Maybe something @c123 could create. At home blow to pop races without the water mess.

    Comment

    • cl23
      Senior Member
      • May 2022
      • 381

      #3
      Originally posted by stretchedtight

      Man I would love to have a version of this where I can use a laser pointer on a toy gun to inflate a balloon (turn a pump on and off as an example) and have a race. Maybe something @c123 could create. At home blow to pop races without the water mess.
      This sounds like an easy task. Just very few basic electronic components and some small compressors required, but always being alone, when using balloons, i prefer a wireless controller without the hassle of hitting a small target with a laser pointer. There are more interesting ways for gamification for me, like some kind of roulette for the amount of air, that will be added to each balloon or using an rc car with a needle to pop balloons etc.

      Comment

      • AlterPlatzer
        Senior Member
        • Jun 2024
        • 1528

        #4
        In the past, I put some effort into constructing my own Balloon Water Race. My stated purpose was more to build a B2P machine than a carnival game.

        The key challenges that I encountered were holding the balloon in place and air supply. Everything else is just basic electrical and plumbing.

        Air supply is a matter of volume more so than pressure. Consumer grade air compressor will supply way more pressure than what is needed, but nowhere near enough volume. There's also the matter of how many balloons are involved and how fast you want them to inflate. It's just basic math to calculate the required CFM from there.

        In this video of the game being played at a carnival, the time between start and pop is less than 10 seconds. A 12" balloon's volume is about .5 cubic feet. To supply enough air to pop a 12" balloon in 10 seconds would be 3 CFM. Now multiply that by 10 nozzles and it jumps to 30 CFM. A 30 CFM air compressor is rather large and quite expensive.



        Restricting the airflow and thereby reducing the required CFM could work, but since only a small amount of pressure is need, I went in a different direction for air supply.

        I bought a 2HP, regenerative blower similar to this from eBay (about $200) and VFD to run it on my single-phase power.

        dr505.png

        That blower has no trouble with balloons at all.


        The nozzles to put the balloons on is a bit more challenging. So let's look at the classic, carnival version:

        XtcTQSr.jpg

        As you may already be aware, some balloons are particularly difficult to B2P because they inflate all the way to the nozzle, leaving nothing to hold against your mouth. The carnival version seems to handle this OK.

        There's a nozzle that one puts a balloon on and a cup that holds it on the nozzle. The rod on the side of the cup is so it can be held down by the metal hook to facilitate using both hands for replacing a popped balloon with a new one.

        rd320fq.jpg​

        So what does the nozzle look like?

        ZYFWVTs.jpg​

        The nozzle isn't all that complicated. The key element is the spring. It has to have enough rate to hold the balloon securely, but not so much that it can't be compressed to facilitate replacing a balloon on the nozzle.

        So far, I have made nozzles that will work on some balloons, but not all. For now, my efforts are toward solving other, more pressing issues and building a B2P machine is on hold for a while.
        It's OK to love balloons.
        There are as many differences in preferences as there colors of balloons. Accentuate what makes us the same and not what sets us apart.

        Comment

        • stretchedtight
          Senior Member
          • Apr 2013
          • 275

          #5
          Originally posted by AlterPlatzer
          In the past, I put some effort into constructing my own Balloon Water Race. My stated purpose was more to build a B2P machine than a carnival game.

          The key challenges that I encountered were holding the balloon in place and air supply. Everything else is just basic electrical and plumbing.

          Air supply is a matter of volume more so than pressure. Consumer grade air compressor will supply way more pressure than what is needed, but nowhere near enough volume. There's also the matter of how many balloons are involved and how fast you want them to inflate. It's just basic math to calculate the required CFM from there.

          In this video of the game being played at a carnival, the time between start and pop is less than 10 seconds. A 12" balloon's volume is about .5 cubic feet. To supply enough air to pop a 12" balloon in 10 seconds would be 3 CFM. Now multiply that by 10 nozzles and it jumps to 30 CFM. A 30 CFM air compressor is rather large and quite expensive.



          Restricting the airflow and thereby reducing the required CFM could work, but since only a small amount of pressure is need, I went in a different direction for air supply.

          I bought a 2HP, regenerative blower similar to this from eBay (about $200) and VFD to run it on my single-phase power.

          dr505.png

          That blower has no trouble with balloons at all.


          The nozzles to put the balloons on is a bit more challenging. So let's look at the classic, carnival version:

          XtcTQSr.jpg

          As you may already be aware, some balloons are particularly difficult to B2P because they inflate all the way to the nozzle, leaving nothing to hold against your mouth. The carnival version seems to handle this OK.

          There's a nozzle that one puts a balloon on and a cup that holds it on the nozzle. The rod on the side of the cup is so it can be held down by the metal hook to facilitate using both hands for replacing a popped balloon with a new one.

          rd320fq.jpg

          So what does the nozzle look like?

          ZYFWVTs.jpg​

          The nozzle isn't all that complicated. The key element is the spring. It has to have enough rate to hold the balloon securely, but not so much that it can't be compressed to facilitate replacing a balloon on the nozzle.

          So far, I have made nozzles that will work on some balloons, but not all. For now, my efforts are toward solving other, more pressing issues and building a B2P machine is on hold for a while.
          This guy on youtube has built one that can inflate multiple balloons. I think he uses a shopvac. I've asked about how he attaches the balloons and wish he would show it upclose as it is attached, etc. https://www.youtube.com/watch?v=Opq7MmjoYrY

          This video he shows making a system with one way valves. https://www.youtube.com/watch?v=Apr-AwsFBU4

          Comment

          • stretchedtight
            Senior Member
            • Apr 2013
            • 275

            #6
            Originally posted by cl23

            This sounds like an easy task. Just very few basic electronic components and some small compressors required, but always being alone, when using balloons, i prefer a wireless controller without the hassle of hitting a small target with a laser pointer. There are more interesting ways for gamification for me, like some kind of roulette for the amount of air, that will be added to each balloon or using an rc car with a needle to pop balloons etc.
            I've found some kits that might work... some pretty basic stuff, Example controlling a 120V switched outlet that a pump could be plugged into. This example would use several of these with pumps like this:
            Maybe some day I'll try. If you have some recommendations please share.

            Comment

            • stretchedtight
              Senior Member
              • Apr 2013
              • 275

              #7
              This is another one I found that used Pneumatic Solenoids to control the airflow. Prototype video
              Finished product with more details

              Comment

              • AlterPlatzer
                Senior Member
                • Jun 2024
                • 1528

                #8
                Originally posted by stretchedtight
                This is another one I found that used Pneumatic Solenoids to control the airflow. Prototype video
                Finished product with more details
                The valves and controller are not all that complicated.

                He's holding the balloons on with zip ties. Anybody can do that. Not exactly a feat of engineering.

                Originally posted by stretchedtight
                This video he shows making a system with one way valves. https://www.youtube.com/watch?v=Apr-AwsFBU4
                OMG! Look at his shirt!

                It's OK to love balloons.
                There are as many differences in preferences as there colors of balloons. Accentuate what makes us the same and not what sets us apart.

                Comment

                • cl23
                  Senior Member
                  • May 2022
                  • 381

                  #9
                  I found a really simple and fast way of attaching balloons for blow or pump to pops:
                  That's it:
                  1.jpg 2.jpg
                  It's just a lightweight 3d-printed part with a hole and some space around it. You only need one hand to put the balloon into the hole, 2 seconds - done! The balloon can't escape on its own until it pops and almost no part of the neck will stay uninflated. It can be used for inflation by mouth and can be used with two sizes of hoses as well. 9 mm tube fits inside, 19 mm fit outside. I made a version with an integrated stop valve as well.

                  You absolutely don't need a 3d printer for this.
                  I made the predecessors of this part from hose, some plastic parts and glue from the home improvement store as seen in this video:


                  Here you can see the 3d printed version. It's suitable for most balloons from 11 to 19 inch:


                  Now, i made a sphere with 9 of these holes and some air limitation for each output, so all balloons will inflate simultaneously as seen on the channel of RainbowBalloonicorn but much more compact:

                  1.jpg 3.jpg

                  I also used a similar approach, but without 3d printed parts here. This inflates 33 balloons at the same time:


                  And here is the machine, that might be most interesting, if you want to see many balloons inflated in a row. It also features the super lightweight stop valves that i designed for each balloon:


                  The next thing, i want to try, would be to have one balloon inflator but lots of outputs that could be switched separately. My main balloon inflator, that you can see in the first video of this post has two solenoid valves for 2 outputs with one blower motor, but one is about 40 USD to support that hight airflow. Having 30 of them would be a lot of money. I'd like to have some 3d printed solution for multiple outputs and i am sure, i will figure something out.

                  Comment

                  • stretchedtight
                    Senior Member
                    • Apr 2013
                    • 275

                    #10
                    [QUOTE=cl23
                    The next thing, i want to try, would be to have one balloon inflator but lots of outputs that could be switched separately. My main balloon inflator, that you can see in the first video of this post has two solenoid valves for 2 outputs with one blower motor, but one is about 40 USD to support that hight airflow. Having 30 of them would be a lot of money. I'd like to have some 3d printed solution for multiple outputs and i am sure, i will figure something out.[/QUOTE]

                    That sounds really cool. Would make a great game... balloon roulette Add 1 second of air here... 5 seconds of air there

                    Comment

                    • cl23
                      Senior Member
                      • May 2022
                      • 381

                      #11
                      Originally posted by stretchedtight

                      That sounds really cool. Would make a great game... balloon roulette Add 1 second of air here... 5 seconds of air there
                      That would absolutely be a great game and my machine measures pressure and volume of air in liters as well so no problem to rise the pressure by 30% or add exactly 10 liters. More exciting ways to pop balloons

                      Comment

                      • cl23
                        Senior Member
                        • May 2022
                        • 381

                        #12
                        Today i started designing the machine for some kind of balloon roulette. It will have 8 outputs only for the first version. If i'll get this working, maybe there will be a larger version. The design supports 3/4 inch hoses so lots of air will be abled to run very fast through it:

                        grafik.png
                        The lower part will be driven by a stepper motor to chose one of the 8 outputs. Air gets into the system from the bottom, goes through the bent tube and exits at one of the 8 nozzles at the top.

                        Comment

                        • stretchedtight
                          Senior Member
                          • Apr 2013
                          • 275

                          #13
                          Originally posted by cl23
                          Today i started designing the machine for some kind of balloon roulette. It will have 8 outputs only for the first version. If i'll get this working, maybe there will be a larger version. The design supports 3/4 inch hoses so lots of air will be abled to run very fast through it:

                          grafik.png
                          The lower part will be driven by a stepper motor to chose one of the 8 outputs. Air gets into the system from the bottom, goes through the bent tube and exits at one of the 8 nozzles at the top.
                          Very cool, will is also cycle the pump on and off? One way valves to prevent deflation?

                          Comment

                          • cl23
                            Senior Member
                            • May 2022
                            • 381

                            #14
                            Originally posted by stretchedtight

                            Very cool, will is also cycle the pump on and off? One way valves to prevent deflation?
                            I will have to figure a way out for wireless communication between my computerized balloon inflator that is standing on the other side of the room and this device, but yes, the pump will be controlling this air output switch for working together perfectly (timing is essential).

                            Each of the 8 outputs might get a one way valve, but by design all inactive outputs already should be more or less airtight without these, even when attached balloons are inflated. I'll see as soon as i can physically test the machine. Yesterday, i already designed a housing for the device and ordered some components, that i need for this project. When they arrive, i can start with the electronics, programming and testing.

                            Comment

                            • xury2004
                              Junior Member
                              • Oct 2023
                              • 3

                              #15
                              Originally posted by cl23

                              That would absolutely be a great game and my machine measures pressure and volume of air in liters as well so no problem to rise the pressure by 30% or add exactly 10 liters. More exciting ways to pop balloons
                              what pressure sensor do you use? I try to make one inflator which inflate balloons to exactly same pressure and volume but I'm having trouble finding a sensor that accurately measures such low pressure.

                              Comment

                              Working...