Do you guys have any problems with the bigger plastic clips?

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • The Masked Looner
    Senior Member
    • Nov 2024
    • 179

    Do you guys have any problems with the bigger plastic clips?

    I've never really had a problem with the really small plastic clips that you'd use on say a 12" balloon (that being said though I've just realised if one were to hit me in the eye that'd be pretty bad, it's a good job I wear glasses).

    But the bigger plastic clips that you'd use for bigger loons like 18", 36", etc I've only used probably around 5 times by now, yet I've already had a couple of unfortunate experiences with them, once when an 18" loon popped the part of the loon with the clip on it shot against my knee and really hurt, a lot more so than when I have just the rubber snap against me, it started bleeding, so I'm then having to use tissue paper to try and stop the bleeding so the blood doesn't get everywhere. Yeah, I can be doing without that hassle in the middle of a session.

    And then just before, I was riding a 36" loon, the part of the loon with the clip shot forwards right across the room and nearly hit the TV, I guess if it did hit the TV or something else it may have caused some damage.

    So, even though I liked the idea of using clips, since it's a lot quicker than tying a knot, and you get a bigger neck on a balloon if using a clip, overall it just doesn't seem worth it, unless I've just been incredibly unlucky.

    What do you guys think of using the big clips for popping sessions? How's it been in your experience?
    Looning since 1989

    To see my pictures of prints and blown up examples: Printed Balloons - Balloon and Inflatable Fetish Forum​
  • LoonerHoax
    Senior Member
    • May 2020
    • 521

    #2
    Mixed experiences here with the bigger clips. Like you, I've been hurt by them flying off a popped balloon. I've had them break in half from balloons popping. They are nice for getting huge necks, but I've had some balloons pop from them.

    Comment

    • Loon119
      Senior Member
      • Jun 2018
      • 494

      #3
      I blew up a 16" balloon in my pants until it was nice and tight and used a clip to seal it. I stood up to fix myself a drink and I was going to go back and see how much bigger it would go. Soon as I stood up the balloon popped and the clip whizzed backwards, whipping my leg and balls no idea why it went backwards

      Comment

      • cl23
        Senior Member
        • May 2022
        • 381

        #4
        I never use these clips for these reasons. They can take your eyesight if you have really bad luck and to destroy a tv or computer screen, much less is enough
        I always use small rubber rings to seal balloons, wrapping it around 4-5 times. These rubber rings i get from the mouth piece of bursted ballons. I use scissors, to remove the rolled end. Sealing a balloon only takes seconds and is absolutely airtight if done properly.

        Doing it this way, you can seal every balloon, no matter how long the neck is.

        Comment

        • The Masked Looner
          Senior Member
          • Nov 2024
          • 179

          #5
          That's a great idea, cl23, I'll try it out next time. Thanks! 👍
          Looning since 1989

          To see my pictures of prints and blown up examples: Printed Balloons - Balloon and Inflatable Fetish Forum​

          Comment

          • The Masked Looner
            Senior Member
            • Nov 2024
            • 179

            #6
            Since I've now got some polystyrene I had the idea of covering a clip with it, my thinking is that it may not fly through the air with as much force as I can see the polystyrene making it more 'floaty', and even if it does still fly through the air with as much force, it should be a lot less likely for it to damage anything including myself.

            I basically carved out the shape of the clip in the polystyrene, and then superglued them together, once the glue was dry they just easily came apart, so I guess polystyrene and plastic don't glue together that well. So instead I used sticky tape and wrapped it around. I've also used stronger Gorilla sticky tape around the hinge as they're quite weak on these clips and can easily fail splitting the whole clip in two.

            I've yet to try the clip out, but if it's successful then that will be great, and I will make more of them. I'll come back with an update.

            SAM_2865.jpg SAM_2866.jpg
            Looning since 1989

            To see my pictures of prints and blown up examples: Printed Balloons - Balloon and Inflatable Fetish Forum​

            Comment

            • Geoff Robinson
              Senior
              • Mar 2024
              • 131

              #7
              You could try using a slip knot

              Comment

              • Guest

                #8
                I don´t like them- for me, they break the illusion, somewhat. I understand that sometimes they are necessary or at least make life easier when working with big balloons, but to me this always seems like taking the easy way out. Or in other words- a bigger balloon that is actually tied shut properly is always a sign that the producer made an effort. I am not such a big fan of bigger balloons in general, but as I always appreciate realism in films or content, those plastic shutters are always a downer. Because in real life no regular person would actually use them, to tie shut a balloon.

                Comment

                Working...