Tips for blowing up a Cattex 94inch giant spiral worker

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • NLooner
    Junior Member
    • Dec 2024
    • 9

    Tips for blowing up a Cattex 94inch giant spiral worker

    Hey there, has anyone got any helpful tips on how to blow up a Cattex 97 inch worker balloon? Bought 2 and the first burst early on at the first head end section. Really want to avoid it happening again and can’t work out of it was technique or an imperfection. Any advice gratefully received!
  • Nopops4me
    Senior Member
    • Jun 2015
    • 976

    #2
    Originally posted by NLooner
    Hey there, has anyone got any helpful tips on how to blow up a Cattex 97 inch worker balloon? Bought 2 and the first burst early on at the first head end section. Really want to avoid it happening again and can’t work out of it was technique or an imperfection. Any advice gratefully received!
    Haven't ever had one of these 'worker' balloons, but with all these long type balloons it is suggested/recommend to start inflating any balloon from the far end (drip point) until you reach the mouth piece (neck). Then clip off/tie it closed. And have fun. If it doesn't make it, then the balloon was inferior/faulty.
    Best of luck.

    Comment

    • LoonerHoax
      Senior Member
      • May 2020
      • 521

      #3
      As Nopops4me said, start at the drip point and keep some pressure on it so each "bump" fills completely before moving to the next closest to the mouth piece. They should fill nice and full using this method.

      Comment

      • NLooner
        Junior Member
        • Dec 2024
        • 9

        #4
        Thanks both, must have been a faulty one I tried then. The end bump just kept getting bigger and popped without moving into the next. I’ll see how I go though with the next one!

        Comment

        • SalmonLooner
          Senior Member
          • Nov 2012
          • 200

          #5
          I also recommend to stretch the balloon first if you haven't.

          Comment

          • Nopops4me
            Senior Member
            • Jun 2015
            • 976

            #6
            Originally posted by NLooner
            Thanks both, must have been a faulty one I tried then. The end bump just kept getting bigger and popped without moving into the next. I’ll see how I go though with the next one!
            Bad luck NLooner. It must have been devastating for you to see that balloon burst early as these balloons are not cheap. The way balloons in general are made is for the 'former' to dip into the liquid latex and when lifted out has the excess latex running down and dropping back into the tank, hence, at the bottom of the former there is the 'drip point'. When the balloon is processed and ready to use, the end furthest from the mouth piece is usually thicker latex and thinner nearest the mouth piece.
            So I reckon your first 94" had a weak spot on that last bulb and gave way while you were blowing it up.
            It's now a while since you first posted. Have you successfully blown your second 94" balloon up to full size??

            Comment

            • NLooner
              Junior Member
              • Dec 2024
              • 9

              #7
              It was totally devastating a) because of the cost and b) because I’m phobic so it did really mess me up. I have since attempted it but bottled it as it started going. I’m going to have to have a word with myself and find a time where I’ve summoned enough courage to get back on the horse… Will keep you updated!

              Comment

              • Nopops4me
                Senior Member
                • Jun 2015
                • 976

                #8
                Yeah NLooner. Try and put that experience of the first 94inch behind you. Not all balloons reach their intended size. Now and again you'll get a balloon burst on you before it's full, that's the nature of balloons.
                Just because you had a balloon burst on you, doesn't mean all you balloons are going to burst on you before full inflation. Get back on as you say "the horse" and get blowing that second 94inch up and enjoy it. That's what balloons are made for, fun.
                Keep us informed. Good luck.

                Comment

                • Guest

                  #9
                  Something that can reduce the chance of unwanted pops close to you is blowing up the balloon only a bit, clipping it off and moving the trapped air through the far ends of the balloon by pressing down on it with your hands before adding more air.
                  That way you stretch it all the way without full pressure; Imperfections will be easily visible and holes will just release air, which is clearly audible, instead of popping.

                  Comment

                  • Platonic_Lnr
                    Senior Member
                    • Mar 2025
                    • 308

                    #10
                    As others have said, blow the balloon up "backwards" by squeezing it so only the last "bump" begins to inflate first, and continue to blow it up.

                    However, it should be noted Cattex's 94 "spiral" balloons do not inflate to 94". I'd say they don't get longer than 6 ft. If you want a serious long balloon, go for the Cattex 67" x 12" or 87" x 19.5"s. Both are cheaper than the spirals, get much bigger, and are easier to inflate. But just like the spirals, inflate them "backwards."

                    Comment

                    • NLooner
                      Junior Member
                      • Dec 2024
                      • 9

                      #11
                      Thanks for all the support and tips. I really love this community for exactly these kind of messages ❤️

                      Comment

                      Working...