Due to a major issue with spam we have disabled a lot of accounts, if you have previously registered and cannot login we may have disabled yours by mistake, please register again, or contact us via the "Contact us" link at the bottom of the page.
When you register, you'll need to make a positive contribution to the forums before you get full access - sorry about this but it's the only way we could find to cut down on the spam. I'd suggest introducing yourself in this thread
If you have any questions, please contact me. Otherwise, enjoy the forums and hopefully we can build a nice community of fellow "looners"
I want to order a GL1200 balloon, but I weigh a lot — 140 kg. Will it be able to support me, and what do I need for that, and how do I contact you?
I saw a gl1200 cow that has a deep cutout in the middle of it and another rope stretches inside the ball, I'll draw a diagram right now, how to do it and how to use it?Where there's a deep cutout in the circle, and it's like another ball is glued in. Honestly, I can't find a photo of this mechanism.,
I don't speak russian, but I think google translate let me figure this out. I also have experience writing for people who are going to use an electronic translator so I'll give that a crack too.
I weigh almost the same amount. GL500s were good for me, sit on them on a soft surface to be safer, it will sink in and be less likely to burst. Cattex uses thick material for GLs so they are very durable.
I don't speak russian, but I think google translate let me figure this out. I also have experience writing for people who are going to use an electronic translator so I'll give that a crack too.
I weigh almost the same amount. GL500s were good for me, sit on them on a soft surface to be safer, it will sink in and be less likely to burst. Cattex uses thick material for GLs so they are very durable.
GL500 is small, but how can it withstand so much? I’m not sure even the 1200 version would be enough for me.
It has to do with the way pressure is applied to the material.
Let's talk some math.
A GL1200's rated size is 87in L x 32in W. It's not an ideal cylinder but let's pretend it is. At rated size the surface area of the balloon is roughly 10,000 square inches. 160kg is about 350 lbs. If you put your entire weight on the balloon, like lying down on it with your hands and feet off the ground, the 350lbs of your body weight is applied to the air inside the balloon, which redistributes the internal pressure force evenly to all of the area that your body is not touching. If the balloon is on a soft surface, lots of that additional weight is also transferred to the surface itself. This is why it's more difficult to sit-pop a balloon on a bed or a sofa instead of a tile floor or unpadded chair.
If we assume that your body has 5,000 square inches of contact area with the balloon, the weight of your body is going to be evenly distributed across the remaining 5,000 square inches -- this math works out to roughly 0.07 pounds per square inch, which is not that much. A balloon inflated to the point of bursting could be up to 2 psi worth of pressure -- keeping in mind that's 2 pounds of pressure pushing on every square inch of the material from the inside. Cattex balloons for the looner market (as well as their decorator balloons, but looner balloons moreso) are also significantly thicker than your standard party balloon so the number might even be higher than that! your weight on such a large balloon does not meaningfully affect the balloon until such point as the added pressure from your weight is the difference between the pressure the balloon can withstand and the pressure it cannot.
This is, of course, a gross oversimplification in pretty much every way but the long and short of it is that a very large balloon can take quite a lot of weight before bursting, as long as there are no sharp edges on your person that are going to apply significantly more force to a far smaller area of the material.
On your bed or other suitably soft surface you could probably sit on a 17-inch balloon inflated to rated size and not pop it.
It has to do with the way pressure is applied to the material.
Let's talk some math.
A GL1200's rated size is 87in L x 32in W. It's not an ideal cylinder but let's pretend it is. At rated size the surface area of the balloon is roughly 10,000 square inches. 160kg is about 350 lbs. If you put your entire weight on the balloon, like lying down on it with your hands and feet off the ground, the 350lbs of your body weight is applied to the air inside the balloon, which redistributes the internal pressure force evenly to all of the area that your body is not touching. If the balloon is on a soft surface, lots of that additional weight is also transferred to the surface itself. This is why it's more difficult to sit-pop a balloon on a bed or a sofa instead of a tile floor or unpadded chair.
If we assume that your body has 5,000 square inches of contact area with the balloon, the weight of your body is going to be evenly distributed across the remaining 5,000 square inches -- this math works out to roughly 0.07 pounds per square inch, which is not that much. A balloon inflated to the point of bursting could be up to 2 psi worth of pressure -- keeping in mind that's 2 pounds of pressure pushing on every square inch of the material from the inside. Cattex balloons for the looner market (as well as their decorator balloons, but looner balloons moreso) are also significantly thicker than your standard party balloon so the number might even be higher than that! your weight on such a large balloon does not meaningfully affect the balloon until such point as the added pressure from your weight is the difference between the pressure the balloon can withstand and the pressure it cannot.
This is, of course, a gross oversimplification in pretty much every way but the long and short of it is that a very large balloon can take quite a lot of weight before bursting, as long as there are no sharp edges on your person that are going to apply significantly more force to a far smaller area of the material.
On your bed or other suitably soft surface you could probably sit on a 17-inch balloon inflated to rated size and not pop it.
So, what is the maximum weight it can support if you sit on it and lift all your limbs off the floor at 100% above the level of this sphere?
It has to do with the way pressure is applied to the material.
Let's talk some math.
A GL1200's rated size is 87in L x 32in W. It's not an ideal cylinder but let's pretend it is. At rated size the surface area of the balloon is roughly 10,000 square inches. 160kg is about 350 lbs. If you put your entire weight on the balloon, like lying down on it with your hands and feet off the ground, the 350lbs of your body weight is applied to the air inside the balloon, which redistributes the internal pressure force evenly to all of the area that your body is not touching. If the balloon is on a soft surface, lots of that additional weight is also transferred to the surface itself. This is why it's more difficult to sit-pop a balloon on a bed or a sofa instead of a tile floor or unpadded chair.
If we assume that your body has 5,000 square inches of contact area with the balloon, the weight of your body is going to be evenly distributed across the remaining 5,000 square inches -- this math works out to roughly 0.07 pounds per square inch, which is not that much. A balloon inflated to the point of bursting could be up to 2 psi worth of pressure -- keeping in mind that's 2 pounds of pressure pushing on every square inch of the material from the inside. Cattex balloons for the looner market (as well as their decorator balloons, but looner balloons moreso) are also significantly thicker than your standard party balloon so the number might even be higher than that! your weight on such a large balloon does not meaningfully affect the balloon until such point as the added pressure from your weight is the difference between the pressure the balloon can withstand and the pressure it cannot.
This is, of course, a gross oversimplification in pretty much every way but the long and short of it is that a very large balloon can take quite a lot of weight before bursting, as long as there are no sharp edges on your person that are going to apply significantly more force to a far smaller area of the material.
On your bed or other suitably soft surface you could probably sit on a 17-inch balloon inflated to rated size and not pop it.
A balloon can lift up a car if there was something to keep the sides from blowing out. Assuming it had a cover to keep anything sharp from touching it. It is just air pressure.
You could put a second balloon inside the first one to double its strength basically.
From my experience I wouldn't worry about it even if you are a heavy person. These GL1200 Balloons are made for 2 Persons even 3 can sit on them.
Just don't touch it with something sharp and you are good to go😊🎈
We process personal data about users of our site, through the use of cookies and other technologies, to deliver our services, personalize advertising, and to analyze site activity. We may share certain information about our users with our advertising and analytics partners. For additional details, refer to our Privacy Policy.
By clicking "I AGREE" below, you agree to our Privacy Policy and our personal data processing and cookie practices as described therein. You also acknowledge that this forum may be hosted outside your country and you consent to the collection, storage, and processing of your data in the country where this forum is hosted.
Comment