How to measure pressure in an inflatable

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • heaviest
    Senior Member
    • Jun 2018
    • 914

    How to measure pressure in an inflatable

    Anyone know how you might go about measuring the air pressure in a pool float?

    With some Googling I determined that a pool float would have an air pressure on the order of 1 psi, unmeasurable using say a tire pressure gauge. Ideally I’d be able to find a gauge that reads 0.1 to 10 psi in 0.1 psi increments, and put it inline with a pump.

    Anyone know what I’d need?
  • heaviest
    Senior Member
    • Jun 2018
    • 914

    #2
    Re: How to measure pressure in an inflatable

    WINTERS Low Pressure Gauge: For Natural Gas & Other Gases, 0 to 5 psi

    I’m thinking this is the ticket. Electric pool toy pumps are rated in the range of 0.5 to 0.7 psi, and I’ve never used one but I bet they don’t work as well as a hand pump. Am I right? I’d bet a modest overinflate is in the range of 1 psi. What I don’t know is what pressure a severely overloaded float is. Is that going to be 1.2 psi or 4 psi? I suspect the former. That is, I suspect the range of pressure from “ most people would do this much by mouth” to “this is the pressure of a 700 pound woman on an air mattress” is going to be 0.6 to 1.2 psi. The smaller the range, the harder it will be to measure accurately. I may not get what I’m looking for.

    If the range is narrow, a 0-2 gauge would be more accurate than a 0-5 gauge, and a digital gauge that reads in smaller increments would be even better.


    0-3 psi gauge



    I also need a way to insert this gauge between a hand pump and an open nozzle suitable for pool toys.
    Last edited by heaviest; 15-03-2023, 14:09.

    Comment

    • Whale Rider
      Senior Member
      • Nov 2022
      • 531

      #3
      Re: How to measure pressure in an inflatable

      Originally posted by heaviest
      Anyone know how you might go about measuring the air pressure in a pool float?

      With some Googling I determined that a pool float would have an air pressure on the order of 1 psi, unmeasurable using say a tire pressure gauge. Ideally I’d be able to find a gauge that reads 0.1 to 10 psi in 0.1 psi increments, and put it inline with a pump.

      Anyone know what I’d need?

      thats the industrial solution... as you can see you can measure pressure differences if you want... but why do you want to measure it?

      Comment

      • heaviest
        Senior Member
        • Jun 2018
        • 914

        #4
        Re: How to measure pressure in an inflatable

        I want to measure the pressure of a particular inflatable with a 700 pound person on it, and then reproduce that pressure with over inflation.

        Comment

        • glovepopper
          Senior Member
          • May 2019
          • 390

          #5
          Re: How to measure pressure in an inflatable

          For measuring low air pressures usually I use a pressure gauge from cheap analog blood pressure monitor. It is calibrated in mmHg, but it is easy to convert these units to PSI or another (100mmHg = 1.9psi).


          Another more advanced option is a digital atmospheric pressure sensor (BMP180 for example, it needs to be placed in a small chamber), an Arduino board, LCD display and simple code. But that's for more technical people

          Comment

          • heaviest
            Senior Member
            • Jun 2018
            • 914

            #6
            Re: How to measure pressure in an inflatable

            Blood pressure gauge….very good idea, and affordable!

            If I understand the bpm180 thing, it, an arduino and a power supply would have to go inside the inflatable. Not as crazy as it sounds. I could slit the pillow of an air mattress and patch it. I’d like to do smaller inflatables too, though. It’d give me real-time data I could plot. Neat. I’ll investigate if there’s a remote sensor like that. The person who would know how to do this is no longer with me. I woman I called Tank.

            Comment

            • glovepopper
              Senior Member
              • May 2019
              • 390

              #7
              Re: How to measure pressure in an inflatable

              The BMP180 sensor may be placed inside a small closed vessel (made, for example, from a medical syringe), connected by a flexible hose to the thing in which you want to check the pressure. There must be 4 thin wires connected to the BMP180, which can be easily sealed with hot glue.
              Instead of an Arduino, you can use a wifi module, such as the cheap ESP8266, and read the pressure wirelessly on your phone. The BMP180 measures absolute pressure, so you have to subtract atmospheric pressure.

              Comment

              • heaviest
                Senior Member
                • Jun 2018
                • 914

                #8
                Re: How to measure pressure in an inflatable

                It’d be cool to get a plot of the pressure as we played with the inflatable, but first I’m going to try the blood pressure cuff just to see if the concept works, and to answer the question of what ranges of pressure we’re talking about. I don’t really care about the absolute number, I just want to reproduce the stress of a heavy person on an inflatable fairy accurately, and I want to be able to measure relative stress of two different loads.

                Comment

                • glovepopper
                  Senior Member
                  • May 2019
                  • 390

                  #9
                  Hi guys, recently I tested adding an air inlet to the BMP280 sensor to use it as an accurate digital low pressure gauge. I simply glued the plastic tube with superglue - sensor survived this operation and works fine
                  The electronic parts shown in the photos cost less than $4 on Aliexpress. I intend to make software that will allow to choose from several pressure units with a button, change the refresh rate of the data on the display, and send the data to computer via usb.​
                  Attached Files

                  Comment

                  • nonpop
                    Soft balloons first
                    • Jul 2024
                    • 104

                    #10
                    Originally posted by glovepopper
                    Hi guys, recently I tested adding an air inlet to the BMP280 sensor to use it as an accurate digital low pressure gauge. I simply glued the plastic tube with superglue - sensor survived this operation and works fine
                    The electronic parts shown in the photos cost less than $4 on Aliexpress. I intend to make software that will allow to choose from several pressure units with a button, change the refresh rate of the data on the display, and send the data to computer via usb.
                    Wow, nice! Impressive work — really clever to just add a simple air inlet like that. I’ve actually been toying with the same idea, but never got around to trying it out myself. Seeing your setup really gets the gears turning.

                    This honestly feels like the start of a real product. Imagine combining it with a silent, programmable pump — one that can both inflate and deflate, keep within safe pressure limits, and even let you set custom pressure patterns or cycles. That would open up a ton of cool applications. I'd definitely pay for something like that!

                    Keep us posted on your progress — I’d love to see where this goes.
                    ​

                    Comment

                    • heaviest
                      Senior Member
                      • Jun 2018
                      • 914

                      #11
                      Nice work, GP! I did do this project (that I described at the start of the thread), at least the hardware part, but I never reported my results because the results I was after were situational. Depends on the inflatable, depends on how you load it, EXACTLY how much you inflate it, etc. I still like the idea, I just haven't done the work.

                      I just bought a 3 psi gauge (I don't remember how I narrowed it down to that range, but it turns out to be correct) and some various size tubing, and by gluing tubes within tubes I ended up with adapters that work for various inflatables. My setup won't record the data and is more difficult to read, but the reading is stable enough to do what I want, which is to measure the pressure of an inflatable with a really large person on it, and then reproduce that pressure with inflation alone.

                      It's been a while, but here's what I remember...

                      Low pressure in an inflatable varies so much that it is essentially unmeasurable. It is essentially zero until the thing is fully inflated, and then it increases so quickly that the point at which you stop inflating matters more than how much weight you put on the thing. I've kinda already suspected this. Overinflation stresses an inflatable more than weight. I can blow until I can't blow anymore, and then get on it, and get less pressure than the last time I inflated it by breath alone.

                      All the posts I've made about loading inflatables with ridiculous weight amount to nothing if your only objective is stressing the thing. You can do that without a lot of weight. But for me, the draw is using inflatables kinda as they are intended, except by people who are way too big for them. So overinflation doesn't do anything for me. As difficult as it is to accomplish, I gotta overload them with weight.

                      But here are some more observations...

                      By mouth, the best I can achieve is in the range of 1.9 PSI (if I recall). It varies depending on how well I can keep my mouth on the thing, so it depends on the valve and the shape of the inflatable near the valve, and on my, uh, performance in the moment lol. 1.9 is more than the battery powered pumps can do, and much less than hand pumps can do, and WAY less than a compressor can do, of course.

                      But here's where the situational thing kinda makes the whole project not as interesting as I thought it might be...

                      What you consider fully inflated varies A LOT. It also depends on the inflatable. If I recall, 0.7 PSI is approximately fully inflated, maybe even less than that, and those battery pumps don't do much better than 1 PSI, and they top out under 1.5 PSI, so "fully inflated" is in that very large range, if you find those pumps give an acceptable level of inflation. Remember, I'm looking for normal usage but by unusually large people, so for me, proper inflation is in that range. Probably 1.2-ish PSI for, say, a sturdy one-person air mattress like an 18-pocket suntanner. But one session to the next can vary a lot, and YOUR preference may be quite different. And different inflatables are "fully inflated" at different numbers.

                      So, I inflate an air mattress to 1.2 PSI and get an 800 pound woman to lay on it, and the pressure goes to... 1.7 PSI. Woopdy doo. I can do better, by mouth, with inflation alone. Or I can inflate to 1.4 PSI, and she gets on it, and it only goes to 1.8 PSI and not the 1.9 I was thinking. See the problem? If I make this about numbers, it's not so impressive, and it's not much fun. An 800 pound woman on an air mattress SEEMS like a lot of stress. I should leave it at that, since that's what excites me. Not the numbers.

                      Granted, the difference in feel between 1.2 PSI and 1.7 PSI is quite a lot. But it's not as much as overinflation.

                      Also, large inflatables are "fully inflated" at a lower PSI than smaller ones. If anything, I overinflate larger inflatables more so than smaller ones, because I'm after the tightness. Problem is, large inflatables ALWAYS develop leaks at high pressure. The thicker vinyl just seems more brittle.

                      Next, runaway stretch depends a lot on the material of the float, and the size of the largest chamber. Larger chambers stretch more than smaller chambers. I could try to determine how thick a vinyl needs to be to avoid a runaway stretch, and use a vinyl that is NOT that thick, but that isn't something I have a lot of control over, other than in the choice of inflatable. But the manufacturers have mostly removed this option from me. Floats large enough to load with a lot of weight are always made of a material that is thick enough to prevent a runaway stretch. For example, at room temperature, not in the sun, I've put as much as 1400 pounds on a slim, one-person mattress, and it takes as much as ten minutes for the pillow to expand enough to explode. And that's the flimsiest inflatable on which I can realistically load that much weight. And the tube end of the mattress? Those NEVER explode. Because it's the largest chamber (the pillow) that will expand. Most of the inflatables that I use to load with a lot of weight (in people) are larger than and made of a thicker vinyl than the slim one-person mats.

                      So, how does weight even stress an inflatable? I believe it's a volume thing. When you sit on it, you are decreasing the volume, which increases the pressure. But then the inflatable stretches, so the pressure goes back down. It will stretch if the pressure exceeds the vinyl's strength, and stop stretching when the pressure falls back below that level. So, measuring smaller inflatables under load is even more variable than larger ones that are thicker vinyl.

                      Folding an inflatable also reduces its volume. Even folding it just partially decreases the volume and increases the pressure. Folding it AND loading it a lot, is, of course, a lot of fun.

                      There is probably much I am forgetting. I should have written things down. I intended to make a post like this a long time ago, but the whole thing turned out to be less interesting than I thought, and I assumed everyone else would be even less interested.
                      Last edited by heaviest; 26-03-2025, 23:07.

                      Comment

                      • glovepopper
                        Senior Member
                        • May 2019
                        • 390

                        #12
                        Hi everyone, as a New Year's gift, I would like to give you my pressure gauge project, which I mentioned a few months ago.
                        Its features:
                        - Measuring range up to approximately 10 psi (relative to atmospheric pressure)
                        - Pressure sampling 10 times per second
                        - Choice of units (psi, mbar, mmHg, hPa)
                        - Switching between absolute and relative values (offset)
                        - Sending pressure data to virtual serial port (USB-serial) for acquisition and processing

                        In the attachment, you can see a sample graph made while pressurizing a 2L plastic bottle with an aquarium pump.

                        Used components - all from Aliexpress:
                        - RP2040-Zero microcontroller board
                        - TFT 0.96" 80*160 IPS (ST7735) display
                        - BMP280 3.3V sensor (GY-BMP280-3.3)

                        Solder the components according to the schematic diagram. Connect to a PC using a USB cable while holding down the BOOT button on the RP2040 board. Open the new drive that appears in the file manager (labeled RPI-RP2 or similar) and copy pressure_gauge_bmp280.ino.rpipico.uf2 file to this drive. This will take a few seconds. Glue the air inlet (plastic tube) to the BMP280 board with cyanoacrylate glue (superglue), taking care not to get glue in the sensor hole.

                        Short press of the BOOT button switches between ABSolute and RELative pressure values.
                        Pressing BOOT for longer than 1 second changes the pressure units (psi, mbar, mmHg, hPa). The selected pressure unit is stored in the flash memory.

                        All documentation (source file and compiled binary, diagrams and photos) included in the ZIP attachment.

                        Good luck!
                        Attached Files

                        Comment

                        • snh61
                          Senior Member
                          • Sep 2017
                          • 133

                          #13
                          hPa is for meteorologists, annoying to use, such as mbar (milibar) is. Put there kPa instead for our European friends.

                          What do you plan to measure with this? This is only for barometric measurements, of the atmosphere around us. 30 up to 110 kPa absolute. From what I found, sensor saturates measurement at about 170 kPa, which would seem to give you about 60+ kPa to measure... But you are well outside the permitted operational range, so the linearity is not guaranteed.

                          If you want to measure pressure in balloons or inflatables, get a proper relative pressure transducer, that a hose/tube can be simply be connected to and use a proper strain gauge amplifier/converter for data acquisition. Calibration likely needed too, initial accuracy is usually not the best, but depends on what you expect. Accurate pressure transducers that come precise without calibration are pretty expensive.

                          Comment

                          • glovepopper
                            Senior Member
                            • May 2019
                            • 390

                            #14
                            @snh61
                            I know that my design is not perfect (it is not a laboratory device) and I am aware of the limitations of the BMP280 sensor. For amateur pressure measurements in balloons and inflatables (usually up to 3 psi/20 kPa), I do not need equipment that costs hundreds of bucks. Even though the BMP280 is operating outside the recommended range, it will still give a more accurate measurement than an analog pressure gauge. Once I have access to a reference pressure gauge, I will make a comparison.

                            I shared the source code so everyone can modify it for their own needs. I quickly added kPa instead of hPa, so I am sharing updated code below.
                            Attached Files

                            Comment

                            • glovepopper
                              Senior Member
                              • May 2019
                              • 390

                              #15
                              Pressure graph while humping plastic pillow. Data collected on Android phone in the Serial USB Terminal app, graph made in Excel.
                              Attached Files

                              Comment

                              Working...