Repairing seam leaks

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Inflover89101
    Member
    • Mar 2019
    • 61

    Repairing seam leaks

    Hi,

    What's the best way to repair seam leaks?
    I've got several of Inflatable world's large inflatables that have a pin hole in the seam which I've located.
    I've never done repairs to seams before so just wondered how's the best way to repair them.

    Thanks
  • lilolover82
    Senior Member
    • Mar 2014
    • 201

    #2
    Re: Repairing seam leaks

    I’ve heard that patching can be done, however it is extremely difficult. I have also heard that you can use certain liquids that turn to gels to seal leaks in seams in inflatables, but I’ve never tried it myself. I do know that leaks in seams are the worst. The air in our inflatable cuties goes out a lot faster from seam leaks. Anyone else with more information on how to fix these kind of leaks is encouraged to reply to this.
    Washington State, United States

    Comment

    • looner98
      Junior Member
      • Mar 2012
      • 15

      #3
      Re: Repairing seam leaks

      depends what toy, and where on the seam. normally you can put a dab of glue on the hole but sometimes they need a patch to strengthen it. Feel free to message me some pics and ill try and help out. if you are in the UK as well im happy to repair them for you if you can get them to me, currently got someones IW bear thats having its leg reattached!

      Comment

      • inbox_pm
        Senior Member
        • Apr 2017
        • 189

        #4
        Re: Repairing seam leaks

        For a small seam holes just one narrow patch along a seam works well. For a big pops on a hard loaded places you need a double gluing, inside and outside. A patch material I usually using from an old popped toys of the same color, or transparent.

        Comment

        • EthylTheAardvark
          Senior Member
          • Nov 2016
          • 169

          #5
          Re: Repairing seam leaks

          You might try experimenting with HH-66 vinyl cement (You can get on amazon.) You want to be careful and very neat with the stuff, because it melts the vinyl around where it's applied, but it makes for a remarkably good seal when it sets. I'd suggest gluing some scrap vinyl together first so you can get a feel for how it behaves. Also be sure to use it in a well-ventilated environment, I'm pretty sure the fumes aren't good for you.

          Comment

          • bbhumper
            Junior Member
            • Jan 2012
            • 24

            #6
            Re: Repairing seam leaks

            I use Flex Shot it is a rubber adhesive in the states you can get it at Lowes or you can try www.flexshot.com

            Comment

            • heaviest
              Senior Member
              • Jun 2018
              • 914

              #7
              Re: Repairing seam leaks

              HH-66 vinyl cement works on small seam holes even without a patch. I'm not particularly careful using it, either. Being uncareful makes for an ugly patch, though. The stuff is messy to work with with the included brush. I'd like to try it with a syringe.

              Comment

              • Whale Rider
                Senior Member
                • Nov 2022
                • 531

                #8
                Re: Repairing seam leaks

                Originally posted by Inflover89101
                Hi,

                What's the best way to repair seam leaks?
                I've got several of Inflatable world's large inflatables that have a pin hole in the seam which I've located.
                I've never done repairs to seams before so just wondered how's the best way to repair them.

                Thanks
                relatively easy, get a decent glue that will stay flexible for all eternity.
                In germany that would be Pattex transparent or UHU Allplast. I prefer pattex transparent.

                Deflate the toy, get clamps without any sharp edges or corners



                test the clamps if these are actually rounded if not file the edges down.

                Put some piece of paper below the inflatable in order to avoid ruining your floor or desk I use cork for that.

                identify where the hole is and on which side of the seam the hole actually is.
                If it is only a small hole no problem nobody need patchiong material for that.

                put the inflatable with the side up where the hole is on your workbench (with paper or cork below).


                Put a Clamp 2 cm from each side of the hole so you can easily find it and the vinylsheet is fixated. Put a 1 cm line with the hole in center on the seam respectively between seam and vinyl sheet.

                now grab a different inflatable and have 2 hours of fun in other words wait until the glue is thoroughly dry that should be about 2 to 3 hours. repeat the above mentioned procedure at least 2 times. so you have 3 layers of glue on the hole.

                Patience is important. with that technique you can even repair complete seam failures of 1m or more in length, just limit the glued length of the seam to 10 cm / 5cm for negative curves for each glue and dry activity.


                Have fun and be patient.

                Comment

                • loonerlee
                  Senior Member
                  • Dec 2018
                  • 179

                  #9
                  Re: Repairing seam leaks

                  I've used stormsure purchased from Amazon to fix pin hole and upto 1cm splits in seems, works fine as its a thick glue and not need for a patch. The glue is water resistant and has some flex. Every split seem Ive repaired has stayed fixed.

                  Comment

                  • Whale Rider
                    Senior Member
                    • Nov 2022
                    • 531

                    #10
                    Re: Repairing seam leaks

                    Originally posted by loonerlee
                    The glue is water resistant and has some flex. Every split seem Ive repaired has stayed fixed.
                    "some" flex might not be enough... If in doubt grab some some vinyl sheet and glue a seam and wait a week. If you cannot roll it up perpendicular to the seam without the glue on the seam breaking the glue is not flexible enough.

                    Each Time you in- and deflate your toy you are changing the direction of the seams tensile load. That will change how the seam is shaped, thats the reason why the gleu needs to stay as flexible as possible.

                    A problem that is often occuring that the glue gets brittle with age and that destroys the seam since the glue and vinyl will then simply break.

                    we are talking about years, pattex transparent has stayed flexible for 10 years still have my first zebra ^^ should call her leaky maybe... several other glues have sadly failed...

                    Comment

                    Working...