Car and truck inner tubes?

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Pinprick Hisser
    Member
    • May 2026
    • 40

    Car and truck inner tubes?

    Oh yeah, quick question. Would it be smart to buy inner car or truck inner tubes. Also, how big would they get and how plump do they get? Also, can they be punctured like inflatables for satisfying hiss? Wouldn't they explode if punctured with a pin?
  • Thinskinned
    Look Out!
    • Jul 2024
    • 247

    #2
    vehicle innertubes are made of thick rubber and can get absolutely massive relative to their uninflated size or size when filled with air but not past ambient pressure.

    Whether or not they'd explode if you punctured them would be a matter of how much pressure is inside them at the time. rubber materials have great tensile strength for their mass, which is why it's used for balloons, innertubes, rubber bands, etc. putting a hole in stretched rubber creates a point at which there is no strength at all, redistributing all of the collective stresses to points around it. If the material is under enough stress, it will fail catastrophically, as the remaining material cannot hold up to the new greater stress placed on it, and it will "explode". if the material isn't under enough stress for a catastrophic failure to take place, it will instead just start to leak from the hole, creating the hiss you're after.

    All that to say, there's a point in the inflation of an innertube where puncturing it will cause it to leak and hiss, and a point where puncturing it will cause it to pop like a balloon. Where's that point? It'll be different for every tube, based on its size, rubber composition, and rubber material

    Comment

    • Pinprick Hisser
      Member
      • May 2026
      • 40

      #3
      Might as well experiment in the future ;3. How big can car inner tubes get vs truck ones. I want them to be huge and to hiss nicely but like you said, there is a point where it would just explode. How to know how big can I inflate them before punctring for nice hiss? ;3

      Comment

      • Thinskinned
        Look Out!
        • Jul 2024
        • 247

        #4
        Trial and error, but thats part of the fun, isn't it?

        The larger a tube is uninflated, the larger it will be when it's inflated, generally speaking -- this should be obvious.

        However, there are many different formulations of rubber out there with different levels of elasticity. Some types are really stretchy and will expand a crazy amount before reaching their breaking point, while others are significantly less stretchy. Again, the thickness of the material matters too. Thinner material will expand more but be less durable. In general, the softer and thinner the material, the more it will stretch relative to its unstretched size.

        Innertubes specifically aren't designed with the idea of overinflating/stretching them in mind, they're designed to be held in place by a tire and inflated to a high(ish) pressure to support the weight of a vehicle, so those considerations are not accounted for when they are designed.

        Comment

        • Pinprick Hisser
          Member
          • May 2026
          • 40

          #5
          Thanks for the info man. I will however post on this thread more things I want to explore in the future like those damn inner tubes. This is all hypothetical (I would definitely do those things with inner tubes in the future ).

          Comment

          • ricky
            Member
            • May 2017
            • 95

            #6
            It depends on the material and how hard you inflate them. The more common ones now are made from butyl rubber, which tend to be a bit stiffer than the natural rubber ones. The natural rubber will be softer and stretch a bit more. And even in those categories the composition and wear may vary. But they both share some nice things in common, super thick, bouncy and have a nice hiss when you push in the valve stem.

            Comment

            • glovepopper
              Senior Member
              • May 2019
              • 390

              #7
              Hi guys, I don't have much experience with inner tubes, but maybe I can offer some advice. If you want to puncture a tightly inflated inner tube without bursting, apply an inner tube patch first, before inflation. Second - puncturing it with a sharp spike might not work. To make a hole large enough for air to escape, use a drill with a small bit or a thin rod heated until it’s red-hot. One last thing - valves on inner tubes. Always remove the valve cores to inflate/deflate faster. Once inflated, you don’t need to put the valve core back in - just screw on the plastic cap to keep the air.

              Comment

              • Pinprick Hisser
                Member
                • May 2026
                • 40

                #8
                Nice info. Might try in future >. I was thinking about using safety pin or thumb tick while inner truck tube is massive and full for a nice loud and long hiss.

                Comment

                • TheMole
                  Senior Member
                  • Nov 2019
                  • 302

                  #9
                  Inner tubes can be a lot of fun, especially used ones that have been on the road a while as they get a lot softer with use. Ask around commercial tire shops that deal with heavy machinery and farm equipment. Often times they're more than happy to give you used ones for no cost at all. Keep in mind, they will make your room smell like a tire shop if you play inside. Especially brand new ones that were folded up for a while. Look for "natural rubber" over "butyl rubber" if buying new, less of that smell and softer feel.

                  PLEASE be careful with any type of compressed air though, there's a ton of energy there even below 10 PSI. Tubes are not like balloons and can burst quite violently if it happens at pressure. The metal valves can especially become a hazard to eyes. Not a worry at low pressure (tube is original size and not expanded) but might want to wear safety goggles if going for high pressures where the tube is expanding beyond the size it would be in a tire. I'd always wear them if you want to deliberately burst your tubes.

                  Comment

                  • Pinprick Hisser
                    Member
                    • May 2026
                    • 40

                    #10
                    We will see in the future. I would need to buy a house somewhere in the middle of nowhere to be able to puncture, explode and pop them without people worrying hahahahah.

                    Comment

                    • glovepopper
                      Senior Member
                      • May 2019
                      • 390

                      #11
                      An inner tube (without a tire) will never hold a pressure higher than 5 psi. A good-quality inner tube can expand to at least twice its original size before reaching its critical point.

                      Comment

                      • Falcon
                        Senior Member
                        • Jun 2023
                        • 170

                        #12
                        Originally posted by Pinprick Hisser
                        Oh yeah, quick question. Would it be smart to buy inner car or truck inner tubes. Also, how big would they get and how plump do they get? Also, can they be punctured like inflatables for satisfying hiss? Wouldn't they explode if punctured with a pin?
                        Ok let's try to answer these in order:
                        "Would it be smart to buy inner car or truck inner tubes" - I could be sarcastic and say - if you want a great ride - sure. But truthfully if you want a tube, it's probably best to ask an agricultural tire shop for one on their junk pile.

                        "Also, how big would they get and how plump do they get?" - some get very big, depends on the one you get. This is a very large innertube:

                        35.5LR32 Firestone Natural Rubber Forestry Tire Tube (TR218A)

                        Properly inflated it will stand around 8 feet tall (approximately)

                        "Also, can they be punctured like inflatables for satisfying hiss?" - yes, but if all you want is to ride it while it deflates, then just loosen the schrader valve (or remove it) and it will hiss with no chance of popping.

                        ​"Wouldn't they explode if punctured with a pin?" - If you don't overinflate them almost certainly not, the rubber is too thick. If you keep the air pressure under 2 psi, you're pretty safe. However repeated punctures will weaken the rubber over time and render your tube impossible to patch. If you want your tube to last, use the valve method.

                        As far as the smell goes, there's a very easy way to keep the smell very low (but why would you, some of us like the smell) just wash your tube (simple soap and water) and gentle coat it with a food grade silicon spray (spray it on a rag and rub it on - it also makes your tube slick).

                        One final warning, if you intend to pop your tube by overinflating it - don't do it indoors, there is some significant energy in some tubes, pretty sure you don't want the metal valve flying through your room....

                        Hope this helps....

                        Comment

                        • Pinprick Hisser
                          Member
                          • May 2026
                          • 40

                          #13
                          It helps. Now I know for the future. So truck tubes do get that big really? 8 foot is like 2.5 meters in my country. That's really big. Can I use it to lounge on it and float in the water? Are they durable that much?

                          Comment

                          • Thinskinned
                            Look Out!
                            • Jul 2024
                            • 247

                            #14
                            Thats not a truck tube, that's a tube for large agricultural equipment like tractors or harvesters. That tube is likely large enough that you'd just fall through the hole in the middle, you'd want something smaller to use as a float.


                            Inner tubes are sized based on the type of tire they'll fit, so it might behoove you to learn tire size codes and how big those tires are and use that information to find a tube size you like.

                            Innertubes are very durable, many people have used them as floats. They're far thicker than pvc swim rings, and those hold up perfectly fine (when used as intended and not how some of us use them)

                            Comment

                            • Falcon
                              Senior Member
                              • Jun 2023
                              • 170

                              #15
                              Originally posted by Pinprick Hisser
                              It helps. Now I know for the future. So truck tubes do get that big really? 8 foot is like 2.5 meters in my country. That's really big. Can I use it to lounge on it and float in the water? Are they durable that much?
                              You asked how big they get, that's one of the largest. It's actually for a grader, it's much bigger than any tractor. If you stick with trucks you're talking about ~ 9-12R20.

                              Properly inflated they would be about 3 to 4 feet tall. Once you get used to the size, you can estimate the height. the first number is the cross section width of the tire, the last number is the rim size so a 12r20 tube would stand ~ 44 inches tall. One thing to be careful about, tubes can be measured in inches (like I did) or in millimeters, when measured in metric, the size measured is somewhat different.

                              The tube I linked was in answer to How big can they get. If you enjoy floating in your tube, I suggest you stick to farm tractor tire tubes, The big tube I linked is great for riding, but far too big to float on (you'd fall through the hole). My preferred tube for floating is 23.1R26, and if you get a tube for floating get a tr218 valve (like in the link), it's nice and short and won't get in your way, also the valve unscrews so you can use a pneumatic inflater on it for much faster inflations. 26 is the largest rim size I'd go for as once you get bigger, the hole gets a bit too large.

                              Comment

                              Working...