Experience with patched inflatables

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • zycram
    Senior Member
    • Nov 2024
    • 408

    Experience with patched inflatables

    I had to repair my inflatables several times using vinyl glue since they tend to spring leaks at the seams (the seam itself does not split but the leak appears directly on one side of the seam). I could have fun with them even if they were patched multiple times but I'm asking you to share your own experiences with patched toys, both in the water (which is important because I have yet to try out my now-patched swimming ring in the lake) and in the bed.
  • heaviest
    Senior Member
    • Jun 2018
    • 914

    #2
    If by "leaks" you mean tiny holes, I've found they hold just fine after patching with vinyl cement. I repair tears up to about a quarter inch. I seal the hole, and when that cures, I reinforce the whole area again, and then a third application to the whole seam. Both sides of the seam. It'll hold so well that if I don't also reinforce the outside seam, it'll blow, when that seam is never otherwise stressed enough before the inner seam blows.

    Comment

    • Seasidelad
      Senior Member
      • Sep 2018
      • 303

      #3
      My IW Fox has been patched a good number of times. It gets a new leak sometimes but I patch it up and use it again as I love the feel of toy. I haven't used it in water would like to try it out though. I guess in water you can find the leak easier to.

      Comment

      • zycram
        Senior Member
        • Nov 2024
        • 408

        #4
        My exact question is how the patched toy holds air if the toy is stretched by the sun. I have two swimming rings but I prefer the smaller one (black Intex which is now patched) for use in the water. The bigger one is better for lying on it.

        Comment

        • TowableStretch
          Senior Member
          • Jun 2017
          • 107

          #5
          My experience? Dreadfull when I use my inflatables in the sun. For some reason all glues tend to get soft again when they get hot.

          Comment

          • inflatedskintight
            Senior Member
            • Sep 2019
            • 124

            #6
            Pretty much all my favourite inflatables have some patches on them. After dozens of inflations they start to develop seam leaks so I end up reinforcing them, and I like to replace the valves with ones that work better for me. Of course, the occasional puncture happens by accident. The repairs seem to hold up OK in the water and sun when I use them outside, but that's relatively rare. The one thing I have noticed is that the adhesive/sealant I use ("Dr Boat") softens too much if I put an inflatable in the clothes drier to soften it, so I can't do that. I just inflate the cold, stiff inflatables gently and let them soften naturally, adding a little more air as I play, and all is good.

            I kind of like having patches on the toys. It makes them more unique, more mine, and reminds me that my favourites are worth the time and effort to keep in good condition. Some of them are toys that I've bought damaged second-hand, and repaired. That makes them extra special.

            Comment

            • PVC Vinyl Enthusiast
              PVC Fetish
              • Jan 2013
              • 197

              #7
              I'm surprised that a portable hand-held product has not been invented that thermally welds PVC repair patches onto puncture sites of inflatables. The inflatable would be restored a virtually puncture-free condition.
              Enjoy soft, shiny and smooth PVC (inflatables and clothing). The 6P-free/10P-free material is total rubbish.

              Comment

              • OverTheTop
                Senior Member
                • Dec 2013
                • 749

                #8
                Originally posted by PVC Vinyl Enthusiast
                I'm surprised that a portable hand-held product has not been invented that thermally welds PVC repair patches onto puncture sites of inflatables. The inflatable would be restored a virtually puncture-free condition.
                Probably because it's just not really feasible. You could try to do that with a clothes iron or soldering iron, but there's a fine line between welding the material together and burning new holes in it. It would also probably damage paint, and it would be tricky to prevent heat from transferring to the opposite side of the toy and creating unintended internal welds as well.

                Comment

                • ricky
                  Member
                  • May 2017
                  • 95

                  #9
                  I use electrical tape for small holes, it works really well. It's pretty stretchy so it stretches with the inflatable as it grows or weight is put on it.

                  Comment

                  • O'Dragon
                    Senior Member
                    • Jan 2024
                    • 298

                    #10
                    A lot of my inflas have a patch somewhere. For now it were only small leaks on seams which I sealed with pvc glue. They are all holding air perfectly again and haven’t developed any other leaks for now.

                    i had two bigger tears once which Inflatable world where so kind to repair as we live in the same country and these inflas are also fine since. Never developed any other tears.

                    so personally i haven’t experienced anything like once a leak developed the toy continues to develop new ones quickly.

                    Comment

                    • InflatableBunny
                      Junior Member
                      • Aug 2018
                      • 3

                      #11
                      IMHE , never use superglue or any cyanoacrylate base glue. Also, don't use any contact glue. Try to get something specific for PVC inflatables with acetone base.
                      In only one patch, I never have to re-patch the same place.
                      What happens on my infla sex dolls, is that as you said, it creates small punctures/small openings in the PVC seams. At the end, is full of small patches all around.
                      I have an anime 150cm (59 inches) that has only 3 patches and it holds all my rides since then.

                      The best: The acetone base glue, slightly melts the PVC creating a fusion bond and patches are ready in 1 minute (10 recommended).
                      The worst: Cyanoacrylate creates a hard crystalline union that breaks and leaks air.
                      Contact glue: some are good, some are not, what I find really difficult is to match the exact size and not creating a glue mess on the surface.

                      Hope it helps!!!

                      PS: Works on sun stretched and ATBC (rubberized/plasticized) treated toys.

                      Comment

                      • zycram
                        Senior Member
                        • Nov 2024
                        • 408

                        #12
                        The one I can get here in Europe is the Bison Vinyl/Plastic glue. I once patched up my Bestway inflatable water hammock too at its critical point and it holds air since then.
                        The upper central seam of my Intex whale began to split and I had to apply a triple patch to fix it (scrap vinyl inside, thick transparent vinyl outside, and, as it was still leaking a bit, another layer of thick vinyl outside. I had another boinking session on it since then. But it's fun just to bounce on it for a few minutes.

                        Comment

                        Working...