extreme heatstretching tecnique

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • duckduck
    Junior Member
    • Jan 2022
    • 8

    extreme heatstretching tecnique

    hi guys, can anyone tell me what technique was used in this case? i attach the picture.
    I have tried various methods (boiling water, sunshine, etc.) but could never get similar results

  • duckduck
    Junior Member
    • Jan 2022
    • 8

    #2
    anyone?

    Comment

    • claire.looner
      Junior Member
      • May 2024
      • 1

      #3
      This almost looks like they might have softened it by adding additional plasticizer - compare this to the results Heath gets at https://www.youtube.com/watch?v=Ih9IxqLM75s

      Comment

      • Luther
        Member
        • May 2023
        • 32

        #4
        I'm not so sure that this can't be achieved using just heatstretching. Some will remember the YT clips of a Dutch man who went by the name of Ryoko, who showed phenomenal results doing heatstretching, especially when applying steam from a steam cleaning device through the valves combined with a compressor. Unfortunately he seems to have completely disappeared.

        However, I believe that such an impressing result like in the lovely photo might also be achieved by subsequently and cautiously applying hot water from the outside, then adding air, then repeat. For this massive thing maybe up to ten times. My favourites at the moment are clear/summer theme printed Intex 21'' as well as Intex and Bestway 24'' beachballs, and I use to apply said process to them mostly three times each.

        That way they get to about double the intended inflated diameter and hence eight times the intended air volume. One needs to be cautious to directly hit only the panels with hot water, not the seams and the poles. Then the results are stunning, they get to the size I like most and are very soft also, and I believe even sturdier than non-stretched beachballs. And they get big time of abuse from me. I also use to patch them up even if they pop with a long rip (heatstretched ones for me mostly pop within panels, not seams) until they are so worn that I let them go, either with a massive b2p or sitpop.

        That said, I'd really like to try out that process with such a clownfish toy like in the photo, however I need to get one first, or something similar. Maybe I'll also find the time to take one of my Intex 24'' beachballs (of which I have a lot in my stash) to the max. I'm really keen on knowing how big it can get. Didn't do this yet.

        Comment

        • Luther
          Member
          • May 2023
          • 32

          #5
          Here's how they supposedly did it

          Nathalie was asked to stretch this chair as much as possible. She does it for the first time. Of course something goes wrong. Good that there is the Horseplay Rescue Kit (really a small miracle when you see what it has to endure). After the repair, she takes the hair dryer again and makes the chair huge. Unfortunately, it bursts at the end!

          Comment

          • Vicci
            Blown to bits
            • Oct 2009
            • 816

            #6
            I can usually get things to double their size with boiling water. It does change the structure of the pvc though - makes them much "crispier", like a carrier bag rather than a squeaky pvc inflatable.

            For Christmas decorations I had some clear baubles with polystyrene beads in from temu - tried over-inflating one to see how big they'd get, the answer was not very big before exploding and making a huge mess with the polystyrene beads.

            However, with a couple of jugs of near boiling water I got them to more than double their size 👍🏻
            Vicci x

            Comment

            • Luther
              Member
              • May 2023
              • 32

              #7
              Originally posted by Vicci
              For Christmas decorations I had some clear baubles with polystyrene beads in from temu - tried over-inflating one to see how big they'd get, the answer was not very big before exploding and making a huge mess with the polystyrene beads.
              Once I heatstretched and overinflated one of those colorful 21 inch beach balls with glitter inside, and at about 175% of its intended diameter it became so bouncy and sexy that I could't help but riding it hard Of course it popped with quite a loud bang at one of the following abuses and the glitter spread all over the apartment, found that stuff even months after when cleaning my rooms

              Got another heatstretched one of the same make, but it serves as decoration only, riding is forbidden

              Comment

              • Luther
                Member
                • May 2023
                • 32

                #8
                Originally posted by duckduck
                hi guys, can anyone tell me what technique was used in this case?
                There are in fact quite a lot of videos of the girls heatstretching toys themselves with a hairdryer on the RYT site, just look at the “stretched” tag.

                Didn't try a hairdryer myself yet, just a hot air gun, and found it not suitable, but will try it out asap with a hairdryer and exactly that blue Bestway whale that they also got there, stretched to an enormous size

                Comment

                • Seasidelad
                  Senior Member
                  • Sep 2018
                  • 303

                  #9
                  I also remember the youtuber who used to get toys to that size. He used the steamer for a minute or so then added air by a compressor then repeated. The inflatable will very weak that size and very hard to reppair if popped. He got an Intex Puppy to a massive size before it burst.

                  Comment

                  • Luther
                    Member
                    • May 2023
                    • 32

                    #10
                    Originally posted by onemoreblow
                    Have to back off the pressure after it reaches a certain point.
                    You are right, I do that too. When the beach ball or whatever it is has stretched to the desired size, I always let them rest for a while, then remove some of the air so that it becomes soft and cuddly, a little like a balloon

                    Comment

                    • Luther
                      Member
                      • May 2023
                      • 32

                      #11
                      Originally posted by Seasidelad
                      I also remember the youtuber who used to get toys to that size. He used the steamer for a minute or so then added air by a compressor then repeated. The inflatable will very weak that size and very hard to reppair if popped. He got an Intex Puppy to a massive size before it burst.
                      Yes, that is the one I mentioned. What a shame that he suddenly disappeared. Does anyone know what happened to him?

                      Comment

                      • OverTheTop
                        Senior Member
                        • Dec 2013
                        • 749

                        #12
                        Originally posted by Luther

                        Yes, that is the one I mentioned. What a shame that he suddenly disappeared. Does anyone know what happened to him?
                        I've heard from others that he unfortunately passed away from COVID.

                        Comment

                        • Luther
                          Member
                          • May 2023
                          • 32

                          #13
                          Originally posted by OverTheTop
                          I've heard from others that he unfortunately passed away from COVID.
                          Really. Maybe he just got a girlfriend and decided to delete his channel because of that?

                          Comment

                          • glovepopper
                            Senior Member
                            • May 2019
                            • 390

                            #14
                            Originally posted by Luther
                            Really. Maybe he just got a girlfriend and decided to delete his channel because of that?
                            More likely... Rather he did not remove the Youtube channel from the afterlife?

                            Comment

                            Working...