Mission (seemingly) impossible: the invisible leak

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • O'Dragon
    Senior Member
    • Jan 2024
    • 298

    Mission (seemingly) impossible: the invisible leak

    Hello everyone,

    I have an IW fya Ryuu dragon from their first run. One day, the right rear leg slowly began to lose air.

    I listened carefully, but nowhere a hiss. Then I used soapy water and checked every inch, but nowhere any bubbles.

    I read somewhere that these dragons can start to develop leaks in the area where the leg is welded to the body, so I double-checked this area. Nothing.

    Then I suspected that air might somehow leak from the valve. But also neither anywhere in the area around it, nor in the slight gap between the plug and the valve, any bubbles formed or could I hear a hissing.

    So now I have a leg that is very clean, but loses air through a seemingly invisible leak. Interestingly, my other red one has developed the same problem on his right rear leg. But even there, no leak that is detectible.

    Maybe someone had the same problem and found a solution? Or maybe someone has an idea what else I could do? Any help would be great, as I would really like to fix this, as it would be very sad if I could no longer use my dragons.
  • ChillinHaze
    Senior Member
    • Sep 2016
    • 143

    #2
    Could be a very small pinhole leak. How long does it take for the loss of air to be noticeable?

    If it is a very small leak it's probably not big enough to cause bubbles from the soapy water.

    A very good trick is wetting your lips and hovering along seams or highly likely spots for leaks, like negative curves. Lips are very sensitive, especially to temperature and you should be able to feel the leaking air stream.

    Another thing is, it could be that the leg chamber has a leak connecting it to the main body chamber which causes the air to actually move into the body chamber. I think you could test that by putting pressure on the main body and see if the leg re-inflates.

    Comment

    • O'Dragon
      Senior Member
      • Jan 2024
      • 298

      #3
      thanks for your tips.

      Ah didn‘t know that it is possible that it can leak inside.
      I‘d say it takes 2-3 hours until slowly noticeable.
      If it is so slow how long do you think would I need to put pressure on the body until enough air went back into the leg to be noticeable? Probably also around 1-2 hours?
      I‘ll try your other tip as well.
      If it turns out in the end that there is internal leaking is there any way to fix it?

      Comment

      • ChillinHaze
        Senior Member
        • Sep 2016
        • 143

        #4
        Fixing an internal leak is possible but rather difficult to do, since you'll have to seperate the leg chamber from the main body, repair the leak and then re-attach the leg chamber.

        I can't really say how long it'll take for the air to flow back into the leg chamber,because that depends on the size of the leak. You could also keep the leg deflated and close the valve while the body chamber is inflated and see if the leg inflates at all.

        Comment

        • O'Dragon
          Senior Member
          • Jan 2024
          • 298

          #5
          That doesn't sound easy. I'll still try the other method you mentioned and if I don't find the leak then I'll see what I'll do.

          ​​​​​​Thank you very much for your help.

          Comment

          • Cinnamon
            Junior Member
            • Sep 2021
            • 11

            #6
            I would try it this way first because it could(!) be easy and fast.
            - Take a flashlight and shine it through the foil of the inflatable in a dark room where you suspect the leak.
            This defect will show up as a brighter spot.

            - If you were able to locate the leak...
            - Get a syringe with a long, blunt needle.
            - Fill it with glue.
            - Insert the syringe carefully through the valve.
            - Keep shining the flashlight through the foil so that you can see the hole and syringe through the foil. If necessary, clamp the flashlight between your knees/legs.
            - Carefully feel your way with the tip. And use your other hand to adjust the foil slightly.
            -If you feel any resistance as you proceed, carefully pull the syringe back a little and then continue.
            - Keep shining the flashlight through the foil so that you can see the hole and syringe through the foil.
            - Apply some glue to the hole and make sure that there is air between the glued hole and the other foil. Otherwise the foils will stick together.
            - Check this condition from time to time!

            Comment

            • craggy2012
              Senior Member
              • Jan 2012
              • 842

              #7
              Air can still diffuse through PVC as it’s actually full of microscopic holes. They’re usually too small for a molecule of air to pass, but just occasionally they can be and some air will slowly escape over time. Helium is even worse to contain as a gas as these molecules are even smaller!

              Comment

              • O'Dragon
                Senior Member
                • Jan 2024
                • 298

                #8
                Originally posted by Cinnamon
                I would try it this way first because it could(!) be easy and fast.
                - Take a flashlight and shine it through the foil of the inflatable in a dark room where you suspect the leak.
                This defect will show up as a brighter spot.

                - If you were able to locate the leak...
                - Get a syringe with a long, blunt needle.
                - Fill it with glue.
                - Insert the syringe carefully through the valve.
                - Keep shining the flashlight through the foil so that you can see the hole and syringe through the foil. If necessary, clamp the flashlight between your knees/legs.
                - Carefully feel your way with the tip. And use your other hand to adjust the foil slightly.
                -If you feel any resistance as you proceed, carefully pull the syringe back a little and then continue.
                - Keep shining the flashlight through the foil so that you can see the hole and syringe through the foil.
                - Apply some glue to the hole and make sure that there is air between the glued hole and the other foil. Otherwise the foils will stick together.
                - Check this condition from time to time!
                Thank you very much, I‘ll try this.

                Comment

                Working...