Is there an easy way to tie a condom like a normal balloon I've tried but they are really slippery from the lube. I have managed after a while after constantly wiping my hands but it hurts my fingers after a while and I worry if I'm too rough the condom will pop.
Tying
Collapse
X
-
If you buy condoms for inflation, buy "dry condoms". They come without any lube but for sure, you can add lube for regular use.
Here, i inflated one to the max and above:
They can take a good amount of air.👍 1 -
I prefer tying condom balloons with receptive rubber bands. I cut the one rubber band into 2 pieces and can tie 2 condom balloons. In this way, I can inflate the entire condom balloon without leaving a reserve for tying.Comment
-
How did you measure the amount of air when inflating?If you buy condoms for inflation, buy "dry condoms". They come without any lube but for sure, you can add lube for regular use.
Here, i inflated one to the max and above:
They can take a good amount of air.Comment
-
Here's a video of how to use elastics on balloons but I think it would work with condoms as well. You can use rubber band or lips of balloons or whatever for this. I find it is just much easier both to tie off and to untie. Video Link
https://youtu.be/eSAcOLyVVn4?si=wYp-AKIj5bhn2aYMComment
-
I prefer to get the lube off the condom first. I smother them in dishwashing detergent then give them a good wash. When dry, I cover them in talc to stop the latex sticking to itself. There are also fine net bags available for washing delicate items in a washing machine that I put them in. I just put them in with the rest of the washing. However I prefer the dishwashing detergent as you can just do the outside of the condom. They tend to stick together more when done in the washing machine.
IPA alcohol can clean it off too, when they are left to soak in it for a while. Surprisingly, plastic balloon tying disks seem to work well with condoms, too. Of course you could also get some dry unlubricated condoms, where available. Trustex used to do some really nice multicoloured ones, that I used to love to use for decorations in place of balloons. They looked awesome, but I've not been able to get any for a while.Comment
-
I am crazy and built an extremely overengineered machine to inflate balloons, latex gloves and anything else
It can measure pressure, liters of air, temperature, time etc., can inflate and deflate balloons on two outputs, can run complex programs and is controllable via smartphone, wireless gamepad, computer or buttons. It is used in most of my youtube videos, so you can find out, how much air will be in many kinds of balloons or latex gloves before they pop:
Comment
-
cl23 That sounds awesome! I've wanted myself to build some device to measure the amount of air a balloon (or glove or condom as those are or a higher interest to me) can take when I'm inflating it - just by mouth, as using a pump would spoil the experience for me :-). Unfortunately I never had time to get to it...Comment
-
Yeah, the problem is, that there are no suitable sensors for about 500 liters per minute available, so i had to use an automotive part. The thing about automotive parts is, that there are no public data sheets, so i had to make about a hundred measurements, to create a characteristic curve for the output signal to liters per minute. That was really tricky, also the measurements (you need something inflatable with a known volume, that is not elastic).cl23 That sounds awesome! I've wanted myself to build some device to measure the amount of air a balloon (or glove or condom as those are or a higher interest to me) can take when I'm inflating it - just by mouth, as using a pump would spoil the experience for me :-). Unfortunately I never had time to get to it...
After all, it has been working perfectly for years and is awesome
😎 1Comment
-
That sounds like quite some significant effort, good job!
Yeah, the problem is, that there are no suitable sensors for about 500 liters per minute available, so i had to use an automotive part. The thing about automotive parts is, that there are no public data sheets, so i had to make about a hundred measurements, to create a characteristic curve for the output signal to liters per minute. That was really tricky, also the measurements (you need something inflatable with a known volume, that is not elastic).
After all, it has been working perfectly for years and is awesome
I guess the automotive part was a MAF sensor - that idea also came to my mind, but I wasn't sure if I was able to implement it properly and if it wasn't too imprecise for such small amounts of air, compared to an engine intake. After some googling, I decided I could rather use a differential pressure sensor and a tube with an orifice, such as in https://www.instructables.com/How-to...ith-Arduino-a/. I even bought the sensor IIRC, but never had enough time to actually put it all together, calibrate it in a reasonable manner and put it to some usable shape
.
Comment
-
Thank youThat sounds like quite some significant effort, good job!
I guess the automotive part was a MAF sensor - that idea also came to my mind, but I wasn't sure if I was able to implement it properly and if it wasn't too imprecise for such small amounts of air, compared to an engine intake. After some googling, I decided I could rather use a differential pressure sensor and a tube with an orifice, such as in https://www.instructables.com/How-to...ith-Arduino-a/. I even bought the sensor IIRC, but never had enough time to actually put it all together, calibrate it in a reasonable manner and put it to some usable shape
.
Yes, i used a regular used MAF sensor from a Ford Fiesta that i bought for a couple of bucks from a commercial car parts seller (Small car => smaller sensor
). It measures even small amounts of air like 10 liters / minute and also > 500 liters / minute precisely.
A good pressure sensor is not less expensive and the instructions from the link look like the same amount of work, that i had, but with worse results, because it is a workaround. BUT keep the sensor, you bought. This is the best one, you can get for the money and has the perfect range for balloons larger than 5". I am exactly using 5 of the same sensors for measuring pressure (MPX5010DP).
The MAF sensor even after 8 years now, puts out the same measurements for my test volume, never failed and the most important - it has temperature compensation in the box and you don't have to do any adjustments in the software. If the air heats up, what it does when the blower motor gets warm, the MAF sensor outputs the same results, no matter if you have 10 °C or 60°C. A lack of temperature compensation will lead to very inprecise measurements if you have no constant temperature and this is not about 1 or 2 %. It makes it unusable.Comment
-
What I like to do is when I know it's full enough while inflating I will slide it off the nozzle, then the bit after where I'm pinching which I will put a clip on I will pull through between two toes, this means I have both hands free and can stretch the bit that I'll be putting the clip on which makes it easier to put the clip on, without loosing air.
The clips I use are these ones which I got off ebay, very cheap:Attached FilesLooning since 1989
To see my pictures of prints and blown up examples: Printed Balloons - Balloon and Inflatable Fetish ForumComment
Comment