Hello everyone I created this discussion for those who want to share their favorite picture or photo with gloves or condoms! I also share mine!
Your favourite picture with gloves or condoms
Collapse
X
-
Tags: None🥰 1
-
-
-
I also love this:Originally posted by onemoreblowMakes me nervous when the fingers bulge out like that. I want to try gluing two gloves end to end, or gluing a balloon to the base of the glove, since that is thinner and usually where they fail for me (or between the fingers/thumb). I figure instead of tying the glove and making it even more stressed, just let that area expand but it needs a seal of some nature.
g2.jpg
I managed to inflate all fingers of a glove on an inflated glove of a specific brand (does not work with every latex glove at all). I have to do it again, because i did not take any pictures, even though it lastet for months in this state, than lost air.
I usually tie the open ending of the glove, cut the tip of a finger and inflate the glove from there, but yes - this is a major point of stress when inflating very big.
It is very hard, to glue gloves properly, because most are chlorinated or have some treatment, that will not allow to glue them, but once, it worked out and it got huge:
gl1.jpg
I also have to try this again, because only one glove got that big, but both could.🥰 6Comment
-
Is there a video?Hello everyone I created this discussion for those who want to share their favorite picture or photo with gloves or condoms! I also share mine!
https://i.pinimg.com/originals/e4/f4...a0c5c58e6b.jpg
Comment
-
-
One of my favorite spontaneous photos that is not a screenshot from a video:Attached Files🥰 3Comment
-
Love these biogel eclipse gloves, so far the most transparent I've seen. I used to have a protexis biogel glove but I can't find it 😕🥰 5Comment
-
Pairs of gloves belong close together - forever
I tried it again and am so much looking forward to inflating these ones:
gl1.jpg
I am not sure, if they will survive inflation. Most latex gloves are really tricky to glue together or it is impossible (unlike most latex balloons). All are glued together in a different way, but all pairs are at least airtight. The pair in the middle looks perfect with its almost invisible seam.
Here are some other tests with gloves, that will be inflated - one with the cuff glued closed, one with a 14 inch balloon as a second air chamber, and one with a small latex patch, because it had a hole:
gl2.jpg
I also really love latex gloves and pictures of them, when they are only inflated like that, without stretching the latex, so i posted them here. They look and feel so good
Here some properly inflated gloves:
gl3.jpg gl4.jpg🥰 5Comment
-
-
Me too, because i tested them yesterday and only the glove with the small purple patch survived full inflation.
All pairs bursted or were torn apart, when one of the gloves was inflated fully. The single glove that was glued closed, was not closed anymore, after i tried to inflate it. The glove with the balloon inside bursted, when i initially inflated the balloon (i should inflate the glove only next time). The thicker latex tore the thin latex of the glove apart.
But these were experiments and i learned something. Latex gloves are really tricky to be glued together due to the special treatment of their surfaces. It is soooo much easier to glue normal balloons together.
The good thing is, that this little patch was perfectly bonded to the latex glove, so there must be a way, to use a latex stripe to connect 2 gloves properly. I tried that once (left pair of the first picture), but i did not do it very well. Maybe next time. I would love to be abled to make more glove pair as in post #6 of this thread.🥰 1Comment
-
It's amazing 🤩 🤩 🤩 What kind of company is this long transparent glove?Pairs of gloves belong close together - forever
I tried it again and am so much looking forward to inflating these ones:
gl1.jpg
I am not sure, if they will survive inflation. Most latex gloves are really tricky to glue together or it is impossible (unlike most latex balloons). All are glued together in a different way, but all pairs are at least airtight. The pair in the middle looks perfect with its almost invisible seam.
Here are some other tests with gloves, that will be inflated - one with the cuff glued closed, one with a 14 inch balloon as a second air chamber, and one with a small latex patch, because it had a hole:
gl2.jpg
I also really love latex gloves and pictures of them, when they are only inflated like that, without stretching the latex, so i posted them here. They look and feel so good
Here some properly inflated gloves:
gl3.jpg gl4.jpgComment
Comment