I cant make much noise because I live with others so i cant use a pump and when i inflate a balloon it gets a bunch of spit into it (mostly bigger ones) and when i deflate it about a day or two later if i try inflating it it gets sticky on the inside and feels as if it will pop
How do i inflate balloons without them getting sticky?
Collapse
X
-
Tags: None
-
Re: How do i inflate balloons without them getting sticky?
Will they pop or will they be fine if i inflate them? -
Re: How do i inflate balloons without them getting sticky?
I have a similar predicament... Although, one thing I figured out is that it always helps to store them somewhere where they aren't being squished. Also helps to try to not spit into them too much. Easier said than done, but it's possible.Comment
-
Re: How do i inflate balloons without them getting sticky?
Some people have claimed that after deflating the balloon, dust the inside with talcum powder. That apparently absorbs the moisture. I would be careful, though, not to breathe the talcum powder in on the next inflation.Comment
-
Re: How do i inflate balloons without them getting sticky?
Turn inside out , dry off & lightly talc. Items needed - A very smooth dowel ( I have cutlery with round dowel like handles approx. 5mm dia.), a couple of sheet of kitchen roll or toilet tissue & talcum powder.
First though, draw off hot water (50/60C) into wash basin & immerse only the stretched part of the deflated balloon, watch it shrivel/ shrink back to original size, dry off & lightly talc. This stops latex sticking together.
Put dowel onto drip point of balloon & push up into body of balloon, up through neck & out of lip opening. Balloon is now inside out & covered in saliva. Dip in the water to clean off saliva, dry off thoroughly & lightly talc.
If you need the lip of the balloon for your way of next inflation, use dowel & reverse balloon to original position. If not you are ready for next inflation.
As Steve inflator says - Take care not to breath in the talcum powder on the next inflation.
Hope this helps, give it a go it may work for you & prevent the balloon sticking together.Comment
-
Re: How do i inflate balloons without them getting sticky?
It is a good idea to keep balloons well dusted to prevent the latex rubber getting sticky, prolongs the life of balloons and makes inflation easier!
Try baby powder instead of talc, it works just as well, is a bit finer grained and less likely to be harmful if you get a bit in yur mouth when blowing up.
Also store them in a cool place away from light.Comment
-
Re: How do i inflate balloons without them getting sticky?
Mine get sticky but they don't usually pop unless I unstick them while inflating them. Just make sure they're not sticking to themselves as they inflate and you should be alright.
Also make sure to store them in a dry area out of the sun, which helps prevent them from sticking after deflating them.Comment
-
Re: How do i inflate balloons without them getting sticky?
As someone else has said here, just blow without spitting. It's easier said than done, but it'll be helpful in the long run and I taught myself to do so.Comment
-
Re: How do i inflate balloons without them getting sticky?
I'm in a similar situation, since a) my favorite part of balloons is blowing them up and b) since I'm mostly a non popper so I always end up deflating balloons multiple times.
What I do is when I'm done playing with a balloon (which typically involves inflating many times), I lay down a piece of paper towel and hold the balloon over it by the very tip (drip point) with one hand. Then I pinch the balloon just below and draw my fingers downwards towards the neck/lip, squeezing the excess saliva out (usually a good couple drops). Then I blow into it a little again just to unstick it (since it's all stuck together after this) before shaking it around a little (again by the drip point) to get any smaller amounts of saliva out. Then I give it a final small blow just to unstick it again before gently putting it away in my shoebox (laid as gently as possible to prevent internal sticking).
It's quick and dirty compared to re-talcling them and the balloons do still stick a bit inside, but it's usually easy to unstick them by simply blowing them up slowly, and they are usually 100% unstuck before the balloon starts to inflate. If you're using big balloons it might be worth using the talc method, but for 12" or smaller balloons my method works pretty well.Last edited by b0f0s0f; 29-12-2016, 00:55.Comment
-
Re: How do i inflate balloons without them getting sticky?
When I don't feel like fumbling to turn the balloon inside out, I drop a cotton ball or two inside the balloon and swish it around.*notices bulge*Comment
Comment