Stretching for Maximum Size

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • someloonerguy
    Member
    • Aug 2016
    • 52

    Stretching for Maximum Size

    Hey, so I've got some of the 24" Amscan balloons from Party City. They're surprisingly stretchy for being from, well, Party City and I'm wondering just how big they can really get before there's significant danger of them popping. I'm mostly a non-popper, only popping anything rarely, so I'm more interested in eeking out as many inches of size as I can to really get the maximum thrill is having one blown up.

    So far the only one I've intentionally popped got to an estimated 40 inches before it burst. It wasn't very stretched out and had only been inflated about two or three times before, and never to its rated size. Now that I know one of these 24"ers can get that big before it bursts without a lot of pre-stretching makes me wonder just how far one of these babies can be pushed. So, I'm wondering, without resorting to heat stretching (which I'm afraid to try) what's the best way to go about getting the most size out of this thing as I can get?

    So far I haven't found any serious defects, just some discoloration, and on its first inflation went to 24 inches, then 27 on the second, where it's currently clipped off. Should I add more in to it every couple of days to get another inch, let it set as-is for a few days before messing with it, or would repeatedly deflating and inflating to push it a little bit further work just as well? I would love to see if this thing could get to be TWICE as big as it's rated, oh that would be such a thrill!
  • blnppr
    Member
    • Jan 2016
    • 98

    #2
    Re: Stretching for Maximum Size

    I prefer going for a more "old school" way of stretching. I like to blow up a balloon to rated size, then lay on it or lightly hump. Increasing the tempo as I go. Then, I stop, blow it up until it feels more full. Sure, I end up popping some while laying on them, but for me, that's part of the fun.

    Comment

    • b0f0s0f
      Senior Member
      • Nov 2016
      • 329

      #3
      Re: Stretching for Maximum Size

      I just tried heat stretching for the first time and I can definitely vouch for its efficacy. I bought some 9" balloons this morning and was somewhat disappointed by their shape (bulb didn't get very big, began to neck early) and tried heat stretching. I would blow the balloon up, deflate it, hold it over my heater (quite hot, could only hold my hand there for 5-10 seconds at a time), inflate, deflate, heat, etc. etc. stretching it by hand after each step. I would also blow a little air into it so it held its shape (but not inflated at all) and then held that over the heater, to heat the air inside with the hopes of heating it more evenly. It was fun to see it expand a little as the air inside heated up.

      After a while I would blow it up big and let it deflate to rated size and it would be incredibly soft and squishy, as if it were an old balloon that had been sitting around long enough to deflate itself, despite already being 9" wide! I decided to see how big it would get, and blew it up to a circumference of 42"(!) (almost 13.5" diameter) before it burst! I think I could have gotten it a good bit larger too (the bulb didn't even feel too tight) but I didn't stretch the neck enough because I was focusing on stretching the bulb, so I believe it burst when the neck got too full.
      Last edited by b0f0s0f; 28-12-2016, 19:11.

      Comment

      • wildheart
        Senior Member
        • Apr 2015
        • 872

        #4
        Re: Stretching for Maximum Size

        Would love to have seen photos. Never tried heat stretching myself but I must give it a go sometime.
        How big will it go? Only one way to find out...
        My website: loonerstories.weebly.com

        Comment

        • b0f0s0f
          Senior Member
          • Nov 2016
          • 329

          #5
          Re: Stretching for Maximum Size

          I was planning on taking photos but in my excitement over how big it was getting I accidentally btp'd it... I'm going to do another one though (a red one, already started to stretch it a bit) so I'll post pictures somewhere when I take them (hopefully with a bigger neck too).

          Edit: Drat, that one burst before getting very big. I measured 35" around (/π = 11" diameter) just a breath or two before it popped. I guess it really does make them unpredictable because the thing was only just starting to get tight. It didn't even neck out. I have another one which has been stretched a lot but not with heat which I might try later.
          Last edited by b0f0s0f; 29-12-2016, 04:07.

          Comment

          • JamesPopper
            Senior Member
            • Nov 2016
            • 143

            #6
            Re: Stretching for Maximum Size

            I inflated mine around 5 times and it got up to 44 inches before i decided to deflate it

            Comment

            • wildheart
              Senior Member
              • Apr 2015
              • 872

              #7
              Re: Stretching for Maximum Size

              Originally posted by b0f0s0f
              I was planning on taking photos but in my excitement over how big it was getting I accidentally btp'd it... I'm going to do another one though (a red one, already started to stretch it a bit) so I'll post pictures somewhere when I take them (hopefully with a bigger neck too).

              Edit: Drat, that one burst before getting very big. I measured 35" around (/π = 11" diameter) just a breath or two before it popped. I guess it really does make them unpredictable because the thing was only just starting to get tight. It didn't even neck out. I have another one which has been stretched a lot but not with heat which I might try later.
              I usually take photos after every few breaths in case it pops. That way you are able to get a photo of it at its maximum size.
              How big will it go? Only one way to find out...
              My website: loonerstories.weebly.com

              Comment

              Working...