Preserving Gl1200s

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • WillNye
    Member
    • Feb 2021
    • 36

    Preserving Gl1200s

    So I've been noticing that the Gl1200s I've been using will develop a large thin spot on them, I'm sure you people know what I mean, like when I would be using a hairdryer to shrink the balloon, there is just that one spot that refuses and it becomes really weak.

    Anyway, out of the 8 Gl1200s I've had altogether, I think it has been 3 possibly 4 that have developed the thin spot. I've also noticed that over time my 1200s will begin to stop expanding length-wise and just bulge out sideways. I managed to get one to 3ft wide and its normal length before it popped, it could have gotten larger but it was already sketchy af.

    I've also noticed it only occurs on my 1200s, I've got 500s and other cattex balloons but tbf I do play with the 1200s more often. I think it may be down to when I'm using the hairdryer to shrink them but I've used low heat settings and high heat settings and still get the got the same problems. I've also used hot tap water and quenched the balloons in the water to shrink them. So at this point, I'm stumped as to why my 1200s degrade too quickly.
  • OverTheTop
    Senior Member
    • Dec 2013
    • 749

    #2
    Re: Preserving Gl1200s

    I would try not using heat to shrink balloons after inflation. Heat will weaken the latex and make it stretchier, and while it may not be to a noticeable degree after one time, it adds up and can contribute to early failures.

    Comment

    • WillNye
      Member
      • Feb 2021
      • 36

      #3
      Re: Preserving Gl1200s

      That is fair, but I've noticed how people are able to keep their 1200s for years before they've finally degraded. Mine last about 5 to 6 inflations before they become too degraded.

      So regarding not constantly using the hair dryer on them, do I just leave them in once I deflate them and just add a bit of powder to stop them from sticking and that should help them last longer? Storing them away from sunlight, moisture and warm environments as well of course.

      Comment

      • Londonj2014
        Senior Member
        • Dec 2017
        • 246

        #4
        Re: Preserving Gl1200s

        Use the cool air/low heat function on your hairdryer, if it has one.

        I always put them in a bag afterwards, add some talc powder, and shake them.

        Comment

        • balloonPatcher
          Senior Member
          • Jun 2020
          • 291

          #5
          Re: Preserving Gl1200s

          For a little extra sessions with you balloon you can do the following:

          You can patch the area with a piece of another broken balloon like a 24".
          I turn the balloon inside out, mark the thin area, cut to a little larger than the size of the area. Wash both the patch and the area with solvent and glue together. Inflate slowly and check for areas that the glue has not taken or thin areas that may need another patch.

          More recently, I smear the thin area with liquid balloon latex and smooth the best I can. You may have to do this 2-3 times to get the balloon to inflate the way you want it eg, you may not have a coat thick enough or may have missed a thin area or two. Again I do this on the inside of the balloon so there is still a nice smooth surface to ride.

          It would be much easier just to start with a fresh balloon but sometimes you just want to be able to use an old balloon a little longer. Hope this helps.

          Comment

          • WillNye
            Member
            • Feb 2021
            • 36

            #6
            Re: Preserving Gl1200s

            I've been using liquid latex to path smaller weak spots and that's helped to preserve my balloons for longer. I'll consider that, Thx.

            Comment

            • OverTheTop
              Senior Member
              • Dec 2013
              • 749

              #7
              Re: Preserving Gl1200s

              Originally posted by WillNye
              That is fair, but I've noticed how people are able to keep their 1200s for years before they've finally degraded. Mine last about 5 to 6 inflations before they become too degraded.

              So regarding not constantly using the hair dryer on them, do I just leave them in once I deflate them and just add a bit of powder to stop them from sticking and that should help them last longer? Storing them away from sunlight, moisture and warm environments as well of course.
              All of that sounds pretty much correct. Talc isn't really necessary unless you're getting them wet or otherwise at risk of sticking, but storing them away from light, moisture, and heat are all good. 5-6 inflations sounds pretty typical in my experience - you may want to experiment a bit with different colors, since the dyes added to the latex can change the properties somewhat. I generally have the best luck with clear balloons, but ymmv.

              Comment

              • WillNye
                Member
                • Feb 2021
                • 36

                #8
                Re: Preserving Gl1200s

                I've only bought crystal-coloured 1200s, mainly cuz Balloon Ace only does crystal colours. I'm thinking of clearing out my 1200s and starting a new collection of them, but getting some opaque ones. So I'll see how those ones hold up.

                Comment

                Working...