I don't think I really need to elaborate here, but I just got a cattex 55" heart-shaped balloon and I stupidly didn't get a smaller-sized heart shape balloon to try and inflate first to get the inflation done right. So does anyone know how to do it without any pre-mature bursting?
How to inflate heart shaped balloons
Collapse
X
-
Re: How to inflate heart shaped balloons
Just stretching. The bit between the two lobes is where the stress resides. If you inflate each lobe while preventing the other from being inflated it makes it easier to inflate and get a good heart shape without it popping prematurely. Having said that, the shape means it will usually pop easier than a round balloon of the same quality. Have fun!Just one more puff...🎈 -
Re: How to inflate heart shaped balloons
There may be videos on youtube, but I've blown up a 35 inch heart or something around that size and I just blew it up like any other regular loon.Comment
-
Re: How to inflate heart shaped balloons
In my experience it depends on the quality of the balloon. This can probably be said in general, but with hearts and shaped balloons it is probably more true. I would stretch the balloon before inflating and then I would try gradually chamber by chamber and finally to the full shape.Comment
-
Guest
Re: How to inflate heart shaped balloons
I adore heart balloons, so have done this a few times.
Put a blanket on the floor first so no chance of premature pops by rough edges.
Then lay it flat, kneel on the right and left sides of the balloon, neck pointing between your legs, so that your knees are about in line with the dip between the two ears.
You want to place your palm on the dip between the two ears so that no air can go there.
Now if you inflate it the air should go just into the ears at the tops of each knee.
Trick is to keep stopping, after its filled with air a certain amount, then kneel on it like you did flat, holding the dip betwwen the ears so that the air squeezes into the ears.
Do this until.its about 60% full and then do it once more, gently kneel on it and try get the air to go into the ears. Or lie across it and hold the v betwwen the ears so each ear pushes out.
Continue to inflate to about 70%.
Then I think the key thing is to leave it well alone for a few hours or even overnight. After that its gentle blasts of air from your inflator 5 seconds at a time. Break for a few hours. Repeat.Comment
-
Re: How to inflate heart shaped balloons
I use Q36 hearts a bit. I inflate them like regular balloons and go to town. I had a double stuff that I was using as a chair. Blew it up 5 or 6 times before the inner one let go. I inflated the outer a bit more and rode it hard sitting in between the lobes. Took a while for it to pop.Comment
-
Re: How to inflate heart shaped balloons
That Cattex 55" heart is a beast!.. I bought a bunch of them from Kaboom years ago and found they pop easily by just inflating them, so I know what you are saying. After a few of them, I began to try different methods of inflation and also found out colors matter as well.
Before Covid, I bought more through Cattex's online store and was amazed at the difference.. there seemed to be less fillers in the rubber this time and they would inflate almost to full without popping. I had a yellow one go almost crystal with a long neck, slightly overinflated.. but when I went to pop it, I had a fight on my hands.. put it on the inflator hoping it would go quick, not a chance.
So like some have said, there is a method.. but it varies. I think getting the lobes inflated a couple times first and then the whole thing.. less pops that way.
UComment
-
Re: How to inflate heart shaped balloons
had never success with hearts so far maybe i try our techniques.... thxComment
-
Re: How to inflate heart shaped balloons
Considering it's been a few months since I brought up this question, I'd like to say I was relatively successful in getting the 55" heart to inflate properly. the end parts are still a little stubborn in inflating and there was a weak spot on the negative curve itself I had to reinforce but other than that, It actually worked. I think my method was to slowly add more and more air with a hairdryer and massage the air around the balloon while keeping the negative curve as uninflated as possible.
Then like a month ago I decided to buy some 36" hearts and I guess I got complacent. I did the massaging technique but then was light well there are no defects or anything so I can begin to add more air with the hairdryer. . . *BANG*, I did notice the negative curve bulged out too much and decided it wasn't having any of it. So, I don't even know if I got lucky with the 55" or not at this point. At least it's fun to play with.Comment
Comment