Upkeeping balloon lifespan

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • bwock
    Junior Member
    • May 2022
    • 13

    Upkeeping balloon lifespan

    Hello all, I'm sure this has been answered before, but I could not find the thread for it. I'd like to know the best ways to make sure a balloon can survive a lot of inflations.

    I got lucky last week and managed to get a Grand MOAB from the balloon vault, which are as massive as they are expensive, and with their rarity id like to make sure this one can hold out as long as possible. I did get a little impatient when I received it last night and blew it up just a little bit to try out, and the end did get stretched out and thin. I'm not rough on balloons, so this thing definitely won't be abused. I do keep my balloons in a dehumidified environment in a box away from the elements, but what else can I do to make them last?

    I also heard you can use a hair dryer to shrink the stretched latex back down, but also heard that can damage the latex and speed up deterioration as well. Can anybody confirm?
  • SweetBouncer
    Senior Member
    • Mar 2020
    • 218

    #2
    Re: Upkeeping balloon lifespan

    This is the best post i have seen in balloon conservation:
    This is if you want to enter some rare balloon into the inheritance of your grandchildren.

    In addition to the balloon, you will need two zipper bags (with a zip), silicone oil (you can use pharmacy, but cheaper from auto products, which is for rubber seals, with a minimum of additives), chlorhexidine antiseptic (not peroxide, not iodine, not any other alcohol crap).

    In addition to time, latex has four main enemies - light, air (more precisely, oxygen), adhesion and fungus. We will fight everything at once.

    1) We wash the balloon of fat, talc and dirt from two (!) Sides. Use mild soap or dish detergent. Wash off the soap completely.

    2) Dry the balloon inside and out. Make sure that the ball does not pick up dirt in the process.

    3) Treat with chlorhexidine on both sides. 1ml per side is enough for a 24'' balloon.

    4) We generously process with silicone from the other side. Can be poured into hand and rubbed.

    5) Pour silicone into one bag. It is enough to cover the bottom by a centimeter.

    6) We squeeze the air out of the balloon as much as possible and put it in the bag, crushing the balloon as little as possible. Ideally, the balloon should go into the bag fully expanded.

    7) Squeeze the air out of the bag (from the bottom to the top), close the fastener.

    8) We put the first bag in the second, squeeze out the air, close it.

    9) Put the bag in a dark and cool corner.

    Congratulations, now your ball will be able to please archaeologists in its original form.

    If you want to complicate things, you can use a vacuum cleaner.

    If there is no task to keep the ball forever, but you just want to extend the life of rotting Tuftex's, then you can ignore all the points except item 4. An extra year of storage is provided to you.

    Comment

    • SweetBouncer
      Senior Member
      • Mar 2020
      • 218

      #3
      Re: Upkeeping balloon lifespan

      It's a rough translation from a russian one.

      Comment

      • Whale Rider
        Senior Member
        • Nov 2022
        • 531

        #4
        Re: Upkeeping balloon lifespan

        Originally posted by SweetBouncer
        This is the best post i have seen in balloon conservation:
        This is if you want to enter some rare balloon into the inheritance of your grandchildren.

        In addition to the balloon, you will need two zipper bags (with a zip), silicone oil (you can use pharmacy, but cheaper from auto products, which is for rubber seals, with a minimum of additives), chlorhexidine antiseptic (not peroxide, not iodine, not any other alcohol crap).

        In addition to time, latex has four main enemies - light, air (more precisely, oxygen), adhesion and fungus. We will fight everything at once.

        3) Treat with chlorhexidine on both sides. 1ml per side is enough for a 24'' balloon.

        4) We generously process with silicone from the other side. Can be poured into hand and rubbed.

        .
        first lets asume we are talking about latex balloons, for chloroprene you dont have a any reliable longterm method since the decay is autocatalytic it will become a gooey sticky viscous liquid.

        so latex enemires: he (or she) is correct oxygen, moisture are really bad enemies. mold can be a problem but mold needs water as long as its dry no mold can develop, personly I have never seen mold attacking latex...

        Keep away from chlorhexidine its kinda acidic. If you want to sterilize: boil the balloons (in my opinion always a good idea since it cant get hotter than 100°C) and dry em from both sides. I would also not use silicone since you would essentially dissolve a bit of latex in the silicone and spread that across the loon can be benificial but I doubt it. At best it does nothing. your worst enemies are water and oxygen you cannot keep outside you can only ake their attack slower. So a ziplockbag is a good first line of defense throw that into a dark box with drying bags and you should be able to keep em much much longer.

        Also try to avoid folding balloons roll them or keep em straight and flat, I know thats not working for my 72" but for 24" it should still be possible.

        Comment

        • SweetBouncer
          Senior Member
          • Mar 2020
          • 218

          #5
          Re: Upkeeping balloon lifespan

          Originally posted by Whale Rider
          first lets asume we are talking about latex balloons, for chloroprene you dont have a any reliable longterm method since the decay is autocatalytic it will become a gooey sticky viscous liquid.

          so latex enemires: he (or she) is correct oxygen, moisture are really bad enemies. mold can be a problem but mold needs water as long as its dry no mold can develop, personly I have never seen mold attacking latex...

          Keep away from chlorhexidine its kinda acidic.
          I have lost balloons, both to oxigen (ozone in particular kind of cracks and devulcanizes the latex), and to a black fungus that grew inside the balloon. So yeah, it may seem as overkill, but considering the price invested, i wouldn't risk any possibility for weakspots to appear.

          And i didn't know chlorexidine was a weak acid,( in solution it's pH can be between5,5 and 7), although latex could be affected by it's acidity the quantity should be small enough 1 ml for 24 inches, and the pH to high, to affect the balloon in any significant way.

          Comment

          • balloonPatcher
            Senior Member
            • Jun 2020
            • 291

            #6
            Re: Upkeeping balloon lifespan

            These are the things that I do to increase the number of inflation's.
            1. after deflating, turn the balloon inside out and dry the rubber with a paper towel or cloth. Re powder with corn starch (or talc) on both the inside and outside of the balloon.
            2. inflate the balloon below the rated size. I've never really counted but I noticed if I inflate fully 100% rated size I would get say 5 to 10 inflation's. If I inflate to 50-60% of the rated size, the number would increase to 50 to 100 inflation's.
            3. inflate regularly say weekly or more - seems to prevent the mold deterioration of the balloon (aspergillis niger or black mold that actually 'consumes' the rubber).
            4. After inflating, candle the balloon for weak spots and thin areas that bulge, mark them with pen and deflate and patch.

            Comment

            Working...