In https://www.blowtopop.net/showpost.p...73&postcount=5 our member glovepopper (https://www.blowtopop.net/member.php?u=22645) explained that he quiets an older model Intex pump by running the pump, which is rated at 220V, on a 220V-110V step-down transformer.
This is, electrically, the same idea as a "rheostat" or potentiometer control - those things we used to see on the wall as slide switches or turn dials to adjust the brightness of a light. They work by reducing the electric voltage getting through from the wall (110V or 220V depending on where in the world you are [for the pedantic among us, myself included .. 100-120V or 200-240V depending, heh]) to "something less".
I have a couple of these, which look like an older version of this product:
.. which I use to control the heat output of "kotatsu" (electric brasier tables, from Japan). The tables already have a rheostat switch, but I find that they run from "quite hot" to "you must need this only in the arctic", so by adding this second rheostat in series, I can control it down to "just keeps my legs a bit warm under the table".
That works, for the electric resistance heater table, or for a traditional incandescent light bulb, because there's nothing "smart" involved that requires any specific input voltage (only a maximum input voltage to not overload the appliance), and also because there's no motor (inductive load) which might overwork and burn out if given too little input voltage.
glovepopper's experience with that specific older AP628 model Intex pump shows that, at least, some inductive loads - the motor in his pump - are okay running on half voltage.
Quick electricity lesson (very non-exact, apologies; more formal and complex and correct definitions are easily available on-line):
Voltage is an "electromotive potential difference", that is, per unit of energy, how hard that energy pushes. 220V pushes twice as hard as 110V.
Current, or amperage, is the quantity of units flowing per second.
Power or Wattage is the total amount of energy flowing, and is the result of multiplying volts times amps. That is, W = V * A
So, take glovepopper's AP628 Intex Quick-Fill pump, 220V-240V, 195W:

At 220V, 195W = 220V * ? A
or A = 195W/220V = a bit less than 1A.
glovepopper drops the input voltage to 110V with his transformer.
The amps don't change.
So the Watts end up also at about half, or around 97W.
The motor runs approximately half as fast, produces approximately half the output volume of air (and much less noise).
I say approximate because inductive loads may not have a linear curve for output based on varying input voltage. I don't know.
And, there's the question for the electrical engineers amongst us...
(or, those willing to experiment with the destruction of a $30 cheap Chinese pink plastic "600W" pump, in a non-flammable environment, with a fire extinguisher standing by...)
Do these common (like the common model 73005 pump that I bought,
https://www.amazon.es/Xrten-El%C3%A9.../dp/B07HHYY7DD ) also work on reduced/ varying input voltage?
If so, we could use a step-down transformer the way that glovepopper did.
Or, we could vary it, using something like the dimmer/rheostat slider off/low..max switches that I use for my kotatsu heaters.
But.
(and this applies to my use of those switches for my heaters, too...)
The rheostat slide switches that I find are all rated for a max of 300W (or less).
Our balloon pumps tend to be 400W and 600W (unless they're the air mattress types, which I guess glovepopper's older Intex pump is; I used to have something quite similar; it came apart many years ago, violently; not great construction quality, unfortunately, and I never replaced it).
So, technically, we shouldn't use this same slider switch for our pumps, as we might overheat the switch, which could be dangerous.
Looking for higher power regulators, I came across this:
It's rated at 4000W max (1/3 of that for an inductive load, which is still 1300W, which is higher than - I think - any of our electric balloon pumps).
It has a straightforward 0 .. low .. max dial (as well as a separate "completely off" physical switch).
It's got a cord to plug it in to the wall, and an electric socket into which to plug the cord of the appliance to be regulated.
I'm thinking of trying this.
Any electric engineers or hobbyists out there who've already done something similar, with the modern generation of cheap pink (or blue, etc) generic (e.g. model 73005) electric balloon pumps, who can comment before I possibly set the house on fire? :-)
This is, electrically, the same idea as a "rheostat" or potentiometer control - those things we used to see on the wall as slide switches or turn dials to adjust the brightness of a light. They work by reducing the electric voltage getting through from the wall (110V or 220V depending on where in the world you are [for the pedantic among us, myself included .. 100-120V or 200-240V depending, heh]) to "something less".
I have a couple of these, which look like an older version of this product:
.. which I use to control the heat output of "kotatsu" (electric brasier tables, from Japan). The tables already have a rheostat switch, but I find that they run from "quite hot" to "you must need this only in the arctic", so by adding this second rheostat in series, I can control it down to "just keeps my legs a bit warm under the table".
That works, for the electric resistance heater table, or for a traditional incandescent light bulb, because there's nothing "smart" involved that requires any specific input voltage (only a maximum input voltage to not overload the appliance), and also because there's no motor (inductive load) which might overwork and burn out if given too little input voltage.
glovepopper's experience with that specific older AP628 model Intex pump shows that, at least, some inductive loads - the motor in his pump - are okay running on half voltage.
Quick electricity lesson (very non-exact, apologies; more formal and complex and correct definitions are easily available on-line):
Voltage is an "electromotive potential difference", that is, per unit of energy, how hard that energy pushes. 220V pushes twice as hard as 110V.
Current, or amperage, is the quantity of units flowing per second.
Power or Wattage is the total amount of energy flowing, and is the result of multiplying volts times amps. That is, W = V * A
So, take glovepopper's AP628 Intex Quick-Fill pump, 220V-240V, 195W:
At 220V, 195W = 220V * ? A
or A = 195W/220V = a bit less than 1A.
glovepopper drops the input voltage to 110V with his transformer.
The amps don't change.
So the Watts end up also at about half, or around 97W.
The motor runs approximately half as fast, produces approximately half the output volume of air (and much less noise).
I say approximate because inductive loads may not have a linear curve for output based on varying input voltage. I don't know.
And, there's the question for the electrical engineers amongst us...
(or, those willing to experiment with the destruction of a $30 cheap Chinese pink plastic "600W" pump, in a non-flammable environment, with a fire extinguisher standing by...)
Do these common (like the common model 73005 pump that I bought,
https://www.amazon.es/Xrten-El%C3%A9.../dp/B07HHYY7DD ) also work on reduced/ varying input voltage?
If so, we could use a step-down transformer the way that glovepopper did.
Or, we could vary it, using something like the dimmer/rheostat slider off/low..max switches that I use for my kotatsu heaters.
But.
(and this applies to my use of those switches for my heaters, too...)
The rheostat slide switches that I find are all rated for a max of 300W (or less).
Our balloon pumps tend to be 400W and 600W (unless they're the air mattress types, which I guess glovepopper's older Intex pump is; I used to have something quite similar; it came apart many years ago, violently; not great construction quality, unfortunately, and I never replaced it).
So, technically, we shouldn't use this same slider switch for our pumps, as we might overheat the switch, which could be dangerous.
Looking for higher power regulators, I came across this:
It's rated at 4000W max (1/3 of that for an inductive load, which is still 1300W, which is higher than - I think - any of our electric balloon pumps).
It has a straightforward 0 .. low .. max dial (as well as a separate "completely off" physical switch).
It's got a cord to plug it in to the wall, and an electric socket into which to plug the cord of the appliance to be regulated.
I'm thinking of trying this.
Any electric engineers or hobbyists out there who've already done something similar, with the modern generation of cheap pink (or blue, etc) generic (e.g. model 73005) electric balloon pumps, who can comment before I possibly set the house on fire? :-)

Comment