Doll balloon inflation

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • zhilman
    Senior Member
    • Dec 2018
    • 161

    Doll balloon inflation

    Hi guys. I have a cattex doll balloon which have been inflated multiple times, but at the body only. Does the head can be inflated fully eventhough the body has been inflated multiple times?

    I made a mistake by inflating the body first at the first inflation. Please kindly advise. Thanks.
  • loonerlee
    Senior Member
    • Dec 2018
    • 179

    #2
    Re: Doll balloon inflation

    Heat shrink balloon with hair dryer or radiator and stretch head of balloon a few times and if imagine it should be fine.

    Comment

    • balloonPatcher
      Senior Member
      • Jun 2020
      • 291

      #3
      Re: Doll balloon inflation



      Balloons United video tutorial for the doll balloon.

      You can also partially inflate the body and place some of your body weight on the partially inflated body to inflate the head. Once the head has been stretched you can continue to inflate. If the head deflates as the body inflates, stop and repeat the process of adding you body weight to reinflate the head.

      Comment

      • zhilman
        Senior Member
        • Dec 2018
        • 161

        #4
        Re: Doll balloon inflation

        Originally posted by balloonPatcher
        https://www.youtube.com/watch?v=y1ke5w8uF7M

        Balloons United video tutorial for the doll balloon.

        You can also partially inflate the body and place some of your body weight on the partially inflated body to inflate the head. Once the head has been stretched you can continue to inflate. If the head deflates as the body inflates, stop and repeat the process of adding you body weight to reinflate the head.
        Is this applies for inflated balloon too? Because I’ve inflated the body quite many times without inflating the head and right now I wanna inflate the head.

        Comment

        • Common Loon
          Senior Member
          • Aug 2020
          • 232

          #5
          Re: Doll balloon inflation

          This is actually a difficult subject! Different doll balloons behave very differently, since it depends on both the strength/thickness of the latex and also the head/body diameter ratio.

          When they're fresh, most doll balloons benefit from having the head fully inflated first before allowing the body to inflate -- the same strategy as any shaped balloon with smaller chambers on the back side, like mouse or bunny balloons.

          But there are exceptions... and Cattex's giant doll is evidently one of them. These, when fresh, you want to inflate body first before the head. The chambers are too similar in size, and the latex is quite thick... so the head often will not build up enough pressure to be able to start the body before bursting.

          In your case, though, where the body has been inflated several times already but the head has not? The only advice I can give is to try inflating just the head, roughly an equal number of times as you've inflated the body, and as fully as possible, not allowing the body to fill at all. Getting a very, very good stretch on the head is the only hope for being able to inflate this entire balloon!

          Comment

          • zhilman
            Senior Member
            • Dec 2018
            • 161

            #6
            Re: Doll balloon inflation

            Originally posted by Common Loon
            This is actually a difficult subject! Different doll balloons behave very differently, since it depends on both the strength/thickness of the latex and also the head/body diameter ratio.

            When they're fresh, most doll balloons benefit from having the head fully inflated first before allowing the body to inflate -- the same strategy as any shaped balloon with smaller chambers on the back side, like mouse or bunny balloons.

            But there are exceptions... and Cattex's giant doll is evidently one of them. These, when fresh, you want to inflate body first before the head. The chambers are too similar in size, and the latex is quite thick... so the head often will not build up enough pressure to be able to start the body before bursting.

            In your case, though, where the body has been inflated several times already but the head has not? The only advice I can give is to try inflating just the head, roughly an equal number of times as you've inflated the body, and as fully as possible, not allowing the body to fill at all. Getting a very, very good stretch on the head is the only hope for being able to inflate this entire balloon!
            Okay I’ll try my best. Thank you for the suggestion!

            Comment

            Working...