Making a space hopper/hoppity hop from balloons

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Guest

    Making a space hopper/hoppity hop from balloons

    If you're asking Why would I? the answer is because if you like hoppers, this is easy to do and a lot of fun.

    1. Get 2-3 good quality latex balloons, 24" to 30" range. I recommend Belbal B250 or something like it. Unless you're around 6'5, a 36" works but is difficult to stay on top of while bouncing.

    2. Sprinkle a light layer of corn starch or baby powder inside one balloon. Thoroughly coat it and pour out all excess powder (talc keeps the layers from sticking during inflation and during bouncing so don't skip the powder).

    3. Tightly fold up lengthwise a second balloon and slide it into the powdered one. Seat it completely within the first balloon and pull out the inner neck until both are even.

    4. Repeat step 2 and 3 if you're using a third balloon.

    5. Important: squeeze out all air from between the balloons. They must touch at all points with only powder between them.

    6. Pinching the necks tight to stop air from re-entering between them, use a pump to slowly inflate the innermost balloon.

    7. Once at a little less than rated size, use a large clip to seal all necks as one. The clip also serves as your handle.

    8. The balloons may now be used as you would a hopper ball. The latex will stretch with bouncing so when the hopper begins to get less bouncy, simply add more air to tighten it up. I've found going a little past rated size is fine if the loons are good ones.

    9. Have fun!

    If you like vinyl hoppers you should love this. The balloon hopper is virtually weightless and, if good quality loons are used and kept tightly blown, super bouncy, giving a totally different feel to your ride than you're used to. I haven't had one pop under me yet and I give them as hard a ride as i do vinyl balls.
    Last edited by Guest; 06-06-2021, 12:27.
  • belcatball
    Junior Member
    • Apr 2017
    • 28

    #2
    Re: Making a space hopper/hoppity hop from balloons

    Hi, Merl-

    I've done this before, too. B250s are good choices for this, especially with double stuffing. Virtually weightless is an experience, too. The stuff below might give you even more toughness/bounciness:

    - Use a B250 in a 36" balloon (usually the outer one eventually splits)
    - Inflate the balloons in a stretchy jersey cotton pillow case closed up with a shoelace. Omnikin covers do the same thing for 10x the price, and they don't stretch.

    For even more rebound (but it won't get off the ground)
    - Stack this on a donut ball (e.g. a red Cando ball rated at 300 lb). Use an inflatable hoop the balloon ball fits into as it gets squished, so it won't fly out from under you.



    I've busted double stuffed B250s and double stuffed Playloons in 1 or 2 sessions, but not this. Getting balloons shipped got really tough in 2020, and I've found this balloon pillow lasts 30 to 60 days.

    Comment

    • Guest

      #3
      Re: Making a space hopper/hoppity hop from balloons

      Hi, Bel,

      Yes, a 36" as the outer layer is always a good idea. It'll take the friction of bouncing on carpet while the 250s handle the weight. When I'm into popping (not with this setup) I use a 36" as a pop shield for smaller loons. It is especially fun with the TPU balloons that I use a lot now. Will have to find a big jersey pillowcase, that's also a good idea.

      You reminded me that the first time I ever tried this was with Playloons back when they were still available at Hobby Lobby. I double stuffed two; size and toughness, they were absolutely perfect for this. 30" as I recall...?

      My current setup is an orange 24" needle inflate bladder inside a 24" white sportball bladder, both from Gopher. Stretching slowly, they're only at 19" at the moment but will be amazingly bouncy.

      Comment

      • Guest

        #4
        Re: Making a space hopper/hoppity hop from balloons

        What size pillowcase is that?

        Comment

        • belcatball
          Junior Member
          • Apr 2017
          • 28

          #5
          Re: Making a space hopper/hoppity hop from balloons

          It's a standard size (20x26) Target Jersey pillow case. It fits a 24" balloon after stretching. For a 36" balloon the euro size (26x26) is better, but they can be pricier.
          The ones I have are 50% Cotton/50% Polyester, the key with Jersey cotton is how it is woven.

          Comment

          • Guest

            #6
            Re: Making a space hopper/hoppity hop from balloons

            After I asked that, I was looking on another thread and saw mention of spandex trash can covers. Found a 40 gal cover cheap on eBay and just bought it. Should be here this week, looks like it will do the job too...I expect it will hold up to actual hopping pretty well

            Comment

            • YouKneeCorn
              Junior Member
              • Apr 2024
              • 17

              #7
              Originally posted by Merl
              If you're asking Why would I? the answer is because if you like hoppers, this is easy to do and a lot of fun.

              1. Get 2-3 good quality latex balloons, 24" to 30" range. I recommend Belbal B250 or something like it. Unless you're around 6'5, a 36" works but is difficult to stay on top of while bouncing.

              2. Sprinkle a light layer of corn starch or baby powder inside one balloon. Thoroughly coat it and pour out all excess powder (talc keeps the layers from sticking during inflation and during bouncing so don't skip the powder).

              3. Tightly fold up lengthwise a second balloon and slide it into the powdered one. Seat it completely within the first balloon and pull out the inner neck until both are even.

              4. Repeat step 2 and 3 if you're using a third balloon.

              5. Important: squeeze out all air from between the balloons. They must touch at all points with only powder between them.

              6. Pinching the necks tight to stop air from re-entering between them, use a pump to slowly inflate the innermost balloon.

              7. Once at a little less than rated size, use a large clip to seal all necks as one. The clip also serves as your handle.

              8. The balloons may now be used as you would a hopper ball. The latex will stretch with bouncing so when the hopper begins to get less bouncy, simply add more air to tighten it up. I've found going a little past rated size is fine if the loons are good ones.

              9. Have fun!

              If you like vinyl hoppers you should love this. The balloon hopper is virtually weightless and, if good quality loons are used and kept tightly blown, super bouncy, giving a totally different feel to your ride than you're used to. I haven't had one pop under me yet and I give them as hard a ride as i do vinyl balls.
              I have tried this myself, I use 3 Cattex 36 inch balloons, and stuff those together. They get pretty big and are sturdy too. i can ride with ease!

              Comment

              • Guest

                #8
                Might try this next time I have a session

                Comment

                Working...