GL Inflation

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Guest

    GL Inflation

    -----
    Last edited by Guest; 30-11-2024, 19:04.
  • craggy2012
    Senior Member
    • Jan 2012
    • 842

    #2
    Re: GL Inflation

    I’ve found them to be nice and tight on first inflation, but they stretch n soften very fast especially if on first inflation you sit or lay full length over them.
    After this they just tend to keep inflating way beyond their maximum but never really become nice and firm like you find as if new. Saying that they do give well once they’ve gone soft and stretchy. If they’re going to go with a loud bang it’ll be a brand new one. Older ones just give out with a soft muffled pop.

    Comment

    • OverTheTop
      Senior Member
      • Dec 2013
      • 749

      #3
      Re: GL Inflation

      It's all about stretching them out. Stretch them with your hands before inflating, then blow them up nice and tight, deflate, and repeat a couple times. Leaving them inflated tightly for a while also helps.

      If you don't want to wait for them to soften up, baking them works great too - toss some in the oven at 290°F for 5 minutes or so (reduce the time by 2-3 minutes if they've previously been inflated) and they'll be super soft on the first inflation.

      Comment

      • Tookus
        Member
        • Nov 2019
        • 80

        #4
        Re: GL Inflation

        My GL 800s are tougher than my 900s, and they last longer. I have a new GL 1200, but I'm afraid to blow it up because they're so hard to find now with the shipping bans. Yet I'm dying to know what it feels like inflated

        The GL800 seems to inflate more evenly than the GL900, I always get my GL900 a little lop sided from end to end.
        Last edited by Tookus; 09-04-2020, 00:07.

        Comment

        • OverTheTop
          Senior Member
          • Dec 2013
          • 749

          #5
          Re: GL Inflation

          The GL1200 is super durable, and the size makes it really hard to overdo it - you won't pop it unless you really try.

          Comment

          • SirSquishy
            Senior Member
            • Mar 2020
            • 233

            #6
            Re: GL Inflation

            I haven't gotten a GL balloon yet, really want to though. How big is the opening/nipple/whatever you want to call it?

            Comment

            • ugurano
              Member
              • Jan 2017
              • 62

              #7
              Re: GL Inflation

              awesome share

              Comment

              • ElPotato
                Junior Member
                • Apr 2020
                • 8

                #8
                Re: GL Inflation

                Originally posted by lyckr
                It's been five years since I bought my first GL balloons and I've tried everything up to the 1200. I always try to start inflating the far end first, as I've been told on the forums for years, which can be a challenge with the bigger ones

                Now what I'm wondering is this. Whenever I inflate them (especially the first time, but also after a few inflations), they always get really tight, even before they seem full. Usually when I see GLs in videos (especially GL1200s) they look a lot bigger and squishier than mine.

                Does anyone have any tips for how to achieve this? I'm guessing I simply have to fully inflate them a few times and then just let some air out when I want to use them, but I'm open for ideas from people who use bigger balloons more often. I actually have similar issues with 36" rounds too.
                I always heat stretch my GL1200. I used to use the oven method, but I lost too many to over stretching and not being usable or coming out crooked.
                Now I use a combination of using a clothes dryer and a high powered pet hair dryer. Before inflation, I put two GL1200 into the clothes dryer for 15 min on high with a large dry towel and a small damp hand cloth.
                Before the dryer cycle is over, I turn on the pet hair dryer and it’s heater so they get warm. Note: The pet hair dryer has about the same power as a shop vacuum plus it has a heating element built in like a normal hair dryer for humans. So it is essentially a Shop-Vac that blows 130degree air. Highly recommended.

                When I take one balloon out of the dryer, I leave the other in to stay warm, I immediately blow it up to full tightness and temporary tie it off. Then I get the other and do the same. I let them both sit for about 10 minutes to let the balloon kind of relax after being at max tightness. I then deflate both balloons and return to the dryer for another 10 minutes, followed by another inflation/deflation. I typically don’t leave them inflated for more than a few minutes before I deflate and throw back in the dryer. After about 4-5 cycles of this will make the balloons about twice the size and still very strong. When I store the balloon, I just deflate and put it in a pillowcase. For the next few times they are used, they don’t need to be reheated and will stay this large size around 5-7 times, while getting just a little larger each time. After you have used it, if you put it back in the dryer you risk it going to the super stretch size which is impossible to get on and very fragile, so I never push them that far unless I plan on just popping it because it’s been used to the max. I think the largest I’ve made one was about 4.5 feet thick and around 11 feet long, but it popped within a few minutes.

                If you don’t want to buy a pet hair dryer, you can simply heat up your electric pump for a few minutes using a hair dryer to make it warm. When it is running it will keep warm air flowing through, giving the same effect.. NOTE: do no try to run a hair dryer while using an air pump, you will flip a breaker and your lights will go off in the house.. ask me how I know...

                Comment

                • BASILIS
                  Junior Member
                  • Dec 2019
                  • 7

                  #9
                  How can i make necks on gl balloons

                  Can someone tell me or help me how can i make necks on gl balloons plz

                  Comment

                  Working...