How to make sure balloons are as inflated as possible

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • somerando
    Junior Member
    • Feb 2020
    • 8

    How to make sure balloons are as inflated as possible

    I recently purchased some 36" balloons for the first time and I was wondering how best to handle them to make sure they inflate as big as possible.

    I know that for 12" and 16" you typically stretch them out a lot pre inflation, but it seems a lot harder to do that with larger ones.

    Any tips would be greatly appreciated

    And as a side note, I'm not opposed to them popping, I just wanna make sure they don't pop prematurely. I wanna get the most bang for my buck I you catch my drift
  • balloon12nonpop
    Junior Member
    • Feb 2020
    • 1

    #2
    Re: How to make sure balloons are as inflated as possible

    Just inflate them until they go hard on first inflation seems to work.

    Comment

    • Asclepio
      Senior Member
      • Sep 2018
      • 539

      #3
      Re: How to make sure balloons are as inflated as possible

      Usually the best way to know they are at the max size is feeling the latex.
      To almost all balloons there is a common rule:
      - Does latex still feels soft?= Go bigger, still has room to grow.
      - Does latex feels hard?= Maybe it reached the max size. (Usually the good quality loons like Tuftex or Qualatex, can handle more air even when the latex feels hard)

      There is an exception to the rule, sometimes balloon like Qualatex 16¨feels hard, but It can handle lots more of air, but I dont trust them, they become unpredictable when you reach 16¨and continue adding air.
      A looner looking for fun, against violence or people with hightened moral idealism…. I just care about loons, so don’t ruin the fun.

      Comment

      • seattlelurker
        Member
        • Oct 2017
        • 51

        #4
        Re: How to make sure balloons are as inflated as possible

        If I read you properly, you're looking at advice for some light stretching...

        I love to blow to pop 24" and 36" Tuftex, always aiming for getting them as absolutely large as possible. I don't like them super soft (I like them to be fairly tight and have a noticeable "you're pushing the limits" feel), so I don't like baking balloons... even though it can yield a huge final product, in my experience they tend to just be soft all the way to the end, with no real feeling of overinflation to scare and excite me.

        Here is my favorite process to ensure I'm pushing the balloons as large as I can:

        I'll usually start by stretching the big balloons by hand, a half dozen times in both directions: lengthwise (tip to nozzle) and across the bulb. It takes a little muscle, but I like to think of it as a warm-up to a work out .

        I'll also use compressed air (compressor, air pump, or vacuum on reverse) to pre-inflate the balloons to near their limit once or twice. Usually I'll inflate them until they are tight and a neck just starts to form, and then pull them off the inflator and put in (for a 24", for instance) 10 or so breaths before tying... sometimes I add more breaths to each successive balloon, pushing each one bigger and building some tension for myself. The warmth and moisture of added breath seems to help the latex stretch further than the dry inflator air alone. [Note of personal balloon preference: I don't usually like a huge separate sticking-out neck, but I love the inflation/tightness point where the balloon starts to get taught, the neck naturally begins to form, and the balloon turns from round to a defined teardrop shape. This is usually the level of inflation that I'm trying to hit here.]

        If I have the time, I'll fill the room with a dozen fully inflated 24" and 36" balloons tied with half-knots. The time that each balloon sits and relaxes while I inflate the others usually gives them a nice pre-stretch, which is apparent once they're deflated again and ready for that *final* inflation.

        This is my favorite starting point; slightly more relaxed and stretchy than fresh from the bag, but still ready to get pleasantly tight as they near the point of bursting. Usually to save hours of blowing, I'll start right back with the inflator, once again getting the balloons back to the point of some initial tightening and a neck beginning to form before I stop the forced air and start blowing myself.

        If you know you want to push the balloons as large as possible and aren't too worried about them popping (or like me, if you are heading inevitably toward it ), then to really hit the biggest size, as they tighten up near the limit I'll put in air and then pause while a little escapes, then repeat... 10 breaths in, hold out the balloon to feel and check size and tightness while 2-3 breaths worth escapes, then 10 more breaths, pause, check, and let a little air bleed out, 10 more... I find that pushing them like this slowly towards the end has given me some incredibly huge balloons, as well as an intensely exciting experience of pushing them larger and larger and tighter. [Again, note of personal preference: You just have to keep going pretty consistently, since by this point the balloons are usually so overinflated that just stopping to admire them for too long often winds up with a spontaneous pop! But as long as the breaks are short and the air keeps moving in or (briefly) out, the latex will keep stretching and you'll find yourself with some amazingly huge, tight, dangerously overinflated balloons... and then with a pleasing spray of latex shreds on the floor, stuck to the wall and ceiling...]

        Sorry for the long rant, but I do hope that helps you get the size satisfaction you are looking for! Now that I've had some time to really think about the process, I am reminded that I have a half dozen pre-stretched crystal purple 24's that survived my last session but are begging to find out just how big they'll get...

        Comment

        • Whoopsapopperlips
          Junior Member
          • Jan 2019
          • 24

          #5
          Re: How to make sure balloons are as inflated as possible

          Blow
          Repeat
          If you hear a loud bang try putting one less blow in the next one.

          Or

          Usually it helps to stretch the neck first, until it gets softer than the bulb.
          First few inflations try to inflate the neck first to ensure a fully necked balloon, then blow until tight.
          Light baking does help (5-10 minutes at 260 between inflations to shrink back to shape).

          Then on the fourth or fifth inflation

          Blow,
          Repeat

          Comment

          Working...