Looner tips (Storage and care)

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • AwesomeGroat
    Junior Member
    • Nov 2026
    • 1

    Looner tips (Storage and care)

    Hi! Very new to the forums here. I'm a looner for about 8 years now, non-popper.

    Recently I have bought printed looner balloons and I love playing with them from time to time. These play sessions can vary from light hearted hugging to downright lewd - getting real sweat/bodily fluids all over. After those sessions, I would then deflate them and store in my drawer in a ziplock bag.

    I really want to keep them long term for playing (also printed looner balloons are expensive, especially when the balloons I only play with are GL1200, 32LN, 40inch+ round) but after some time they will start developing mold, inside and outside. I'm not too sure of what mold does to balloons but it sure does not look safe to me to breathe in. I searched through the forums for storage tips and found some, namely:

    1. Dipping the balloon in hot water after use
    2. Not inflating balloon by mouth (kinda impossible, I will still do it at times)
    3. Store in a dark place away from sunlight
    4. Drying it after use.

    How effective are these storage tips and what are the recommended methods? Currently, the storage tip I have employed are keeping the balloons in my drawer that is away from sunlight. I also try to keep my balloons clean after rough sessions by wiping them down with wet tissues and letting them dry out. I'm also thinking about using baby powder as a dessicant to prevent moisture.

    In the place I live, the temperature and humidity is pretty high. So in addition to the above (if they work), what are the storage tips would you suggest to me to keep my precious printed balloons for as long as possible?

    Tldr: What are the balloon storage tips after playing with them and how effective are each of them? What does mold do to balloons? Do I have to clean the ziplock bag that stores my balloons after heavy play sessions?

    Thank you so much!


  • Dutch looner
    Member
    • Nov 2025
    • 31

    #2
    Interesting to hear and what i usually do after playing with them is to whipe them clean and dry. I also live in a humid climate so i keep used and new balloons separated and they are all in ziplog bags with a few silica gel packets in the bag to suck up excess moist, i have got balloons that are more then a year old and still look as fresh as the day i got them.

    Comment

    • Folly
      Junior Member
      • Oct 2026
      • 24

      #3
      Unless you enjoy blowing them up by mouth, get a pump of some kind to inflate them. Can be electric or manual, whatever you like. That will prevent moisture from your breath to degrade the balloons from the inside. Using a pump will help a great deal for longterm storage, as they noticeable last longer. Also, I personally severely dislike how the air smells when deflating a balloon that has been blown up by mouth.

      Comment

      • lucid
        Senior Member
        • Sep 2016
        • 1174

        #4
        For long term storage you can't beat ammo cans. That's literally the purpose of the cans. They have a rubber gasket around the entire lid and when those things snap shut, you can just tell, aint a bit of air, light or moisture getting in there. I store both balloons and ammo in them, separately of course lol. You can also throw some desiccants/oxygen absorbers in there if it makes you feel good. It does me.

        You can get the .50cal milsurp ones usually for about 15-20 and they are classic. I honestly much prefer the cheaper plastic ones. They are bigger and lighter. You can even get plastic ammo crates now and store your whole stash in there with room to spare (for now.)

        If you're interested, Plano makes good ones but MTM is my favorite.

        Comment

        • Missy
          Member
          • Oct 2026
          • 73

          #5
          Approaching the problem scientifically:
          • Mold (fungus) doesn't need light and can thrive in the dark;
          • Dipping or rinsing with hot water does little to nothing to fungal spores;
          • Mouth inflation introduces not only water vapor but the bio substrate (e. g. mucus) for mold to grow on;
          • ​Drying the balloon inside (like blowing with dry air) and putting a small pack of silica gel (like that from a pill can) into it should help;
          • ​Fungi don't really like acids. Maybe rinsing the balloon with acetic acid (synthetic vinegar) will help? Drying it inside afterwards, of course.
          • Latex balloons are perishable by nature. Prioritize your health and discard used balloons after some time.
          non-popper

          Comment

          • Thinskinned
            Look Out!
            • Jul 2024
            • 247

            #6
            I use silica gel as a dessicant. Every roll of 3d printer filament I buy comes with a big bag of silica gel pellets, which I just toss in my stash box.

            My stash box is a big plastic tote, it's not sealed but it's pretty tight. I keep all my new balloons in zipper bags that I squeeze all the air out of. I'm not a huge re-user of balloons except the larger and more expensive ones, and they get their own bag with more silica gel inside. moisture is the #1 enemy so removing the moisture is important.

            Comment

            • Folly
              Junior Member
              • Oct 2026
              • 24

              #7
              Also, once a balloon has already developed mold-growth, I would throw that shit out ASAP. It shouldn't be about getting rid of the mold, it should be about preventing it's growth in the first place.

              Comment

              • balloonPatcher
                Senior Member
                • Jun 2020
                • 291

                #8
                Mold (species such as aspergillis niger and others)are a significant problem for natural latex. A suggestion for longer term storage is to rinse the balloon with bleach(diluted)to reduce or kill the mold and mold spores. Fully chlorinating the latex would be the best long term but it takes preparation to protect yourself from the chlorine gas which can be dangerous. Candy coated offers a latex chlorination service. https://candycoatedkink.com/service-...y=chlorination

                Comment

                Working...