Belbal 17" – tiny leaks near the knot?

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • pinpopper
    Member
    • Mar 2019
    • 73

    Belbal 17" – tiny leaks near the knot?

    I recently tried Belbal 17" balloons for the first time. I like to inflate my balloons very large, with a long neck, so they’re really tight then tie them off.
    I noticed quite a few of them slowly deflated over a few hours. When I checked them, the problem seemed to be tiny holes right next to the knot.

    At first I thought I might be catching the latex with my fingernails while tying, so I tried tying a few while wearing latex gloves. That seemed to help slightly, but I still had some develop the same tiny leaks.

    For those who regularly use Belbal 17s: is this a known issue, possibly a bad batch, or am I simply pushing them too hard when inflating?

    Interested to hear your experience!
  • Dutch looner
    Member
    • Nov 2025
    • 31

    #2
    Good question, and i use them all the time but i have never had any leaks or holes near the knot even after being a little rough with them. Maybe you have a bad batch, i have a bad batch of belbal 14s at the moment with all sorts of defects but the 17s are very reliable for me and i have all the different versions aswel.

    Comment

    • Bloonr
      Member
      • Jul 2026
      • 50

      #3
      Ive never had any issues with belbals other than maybe the one or 2 balloons out of hundreds that pop unexpectedly. Although i dont know if this is 100% true but cattex 14 inch balloons are the same as belbals and i got them once and had this issue with tiny holes forming around the knot. I like to blow my balloons as tight as possible. I dont stop blowing until the neck is filled and i get 2 or 3 breaths into the round part (to a point i can visibly see it start over stretching). So tying the cattex's that time nearly every single one of them would get a small hole when i pulled tight on the knot after tying it to make sure its tight enough. Ive still bought cattex 14 inch balloons since then and never had the same issue (unless i repeatedly blow the balloon up in the neck part over and over). Id say it was just a bad batch and i assume yours is too unfortunately

      Comment

      • Dutch looner
        Member
        • Nov 2025
        • 31

        #4
        That is so interesting and i know there is a difference between the pastel, metallic and soap. I wonder what your favourite one is?

        Comment

        • Asclepio
          Senior Member
          • Sep 2018
          • 539

          #5
          Only thing I noticed with my belbals 17” is a very high level of unexpected pops when they are overinflated. Seriously of 10 overinflated balloons almost 7 pops after a few minutes.
          Kalisans get blown the same and they almost never pops unless I really push them intentionally.
          A looner looking for fun, against violence or people with hightened moral idealism…. I just care about loons, so don’t ruin the fun.

          Comment

          • Guest

            #6
            I've never noticed tiny holes, however I did have a batch a while ago where most popped as I was pulling on the neck. When blowing up balloons I tend to inflate them really tightly until the neck is just starting to form, then give the neck a good tug so the air distributes into it and then top the whole balloon up to make it tight again. At least half of these (out of 10/12) burst as soon as I pulled the neck out, which is unusual. At this point, they weren't even that overinflated.

            Comment

            • onemoreblow
              Master Over Inflator
              • Sep 2013
              • 131

              #7
              Same here with belbal, some are really good but sometimes it is like they were made in a different factory. I think the only brand I have had 100% luck and consistent quality is sempertex.

              Comment

              • T178
                Junior Member
                • Aug 2021
                • 28

                #8
                when you tie them, don't pull the knot to tighten in. It can cause latex to tear

                Comment

                • Slugamano
                  Senior Member
                  • Jul 2016
                  • 276

                  #9
                  Sometimes I can experience something similar when I'm trying to tie the knot. It's embarrasing and I immediately pop the balloon, with adding some more puffs or stabbing it with a pencil or any sharp object...

                  Comment

                  • TheBiggertheBetter
                    Member
                    • Dec 2020
                    • 71

                    #10
                    I have a bag of Belbal solids with a large number of defects. Not impressed

                    Comment

                    Working...