Pumps?

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Mlooner101
    Member
    • Jul 2026
    • 94

    Pumps?

    This has probably been asked a load of times on here but just wondering what pumps you all use (if any at all)? I have got a 600W generic one from Amazon as attached, I have no idea why it's shaped like a grenade 🤣 It does work quite well and the flexible hose is handy for larger balloons, however it is starting to show its build quality and a lot of the clips for the nozzles have snapped.

    Any better suggestions out there? ✌️

    Screenshot 2026-07-20 at 15.59.51.png
    Attached Files
  • Balloonboy99
    Member
    • Sep 2019
    • 52

    #2
    I've ended up with an assortment of pumps, I think the first one I ever got was a "Balloon buddy" pump from a local craft shop that is still going strong 10 years later, it was fairly cheap (about £20) and doesn't seem to overheat.

    I have a few manual pumps, so I have one of the qualatex hand pumps that I use for anything up to 18" balloons if I'm only inflating a few, and it lets me check for weak spots easily. I also have an Intex Double Quick II pump that is a lot faster than the Qualatex pump, it can blow up a 12" in two or three strokes so it's good for the larger balloons.

    My favourite pump though is my Zibi Z32 which I managed to get off Ebay for about £40, but they can be really hard to come by. I wanted a foot pump for it but couldn't find any so I ended up buying a cable that is a bit like an extension lead with a foot switch at the end, it makes it much easier to blow up shaped balloons like dolls and ducks where you need to inflate the end of the balloon first.

    I also sometimes use my computer duster as a pump because the air flow is really good on it and it stays cool, plus it helps that it's more portable than my other pumps. I think that's called a CompuCleaner?

    The only downside to them all is that they don't have the hose like yours does, other than the Intex hand pump, although I've been tempted to DIY my own pipe in the future.

    Comment

    • Mlooner101
      Member
      • Jul 2026
      • 94

      #3
      Nice one, blowing up things like airships can be hard to get right with my pump cause it's very powerful, bit of a technique to it!

      Comment

      • Thinskinned
        Look Out!
        • Jul 2024
        • 247

        #4
        I love pumps, I'm always looking for new and exciting ways to inflate balloons, as the inflation aspect itself is very exciting to me.

        I have the following:

        Makita DAS180 -- this is really fast, will pop a Q16 in no time flat and has no issues starting any balloon from limp. I've 3d-printed custom fittings for it so I can attach hoses to it, with additional custom fittings for the end of the hose to attach balloons to.

        a KICA Jetfan 2 Max -- this is a very well-made but rather expensive take on the cheap amazon computer dusters, it can start any balloon 12" and under from limp with no problem. I don't know if it has the pressure to pop any balloon I put on it, it probably can do a china 36" paddle or other thin larger balloon and maybe some others. have not tested. fittings can thread into each side, and I've 3d printed a stand that threads onto the backside so I can orient the pump with the airflow going up, as well as output fittings to hold balloons or a hose.

        a cordless balloon inflator from amazon, it's gray and yellow and about the same size as a manual pump but is rechargeable and inflates balloons very quickly. Have not found anything it can't start, maybe smaller modeling balloons. I have no doubt it could pop anything I put on it but I have not tested.

        I also have an amazon pink box inflator. it works fine, nothing really to say here, we all know how they work and what they do.

        I have an old foot pump from an air mattress, I think it's from the 70s or maybe earlier. works great, though it's a bit squeaky.

        I just got a usa-market Zibi off eBay, not sure what the model number is but it's visually and functionally very similar to the Z32, it's been basically impossible to find information on it. It's amazing, and worth every penny. I have set it up with a voltage regulator that I can use to slow down the pump so it won't pop balloons and a line footswitch so I can control it from a distance. has no issue popping any balloon I put on it. I have also 3d-printed some attachments for it that allow me to affix larger balloons to the nozzle easily and hold them in place as well as a hose that I can attach (3/4" or 19mm ID vinyl tubing fits snugly over the barb,) to get some range. goes without saying that I've also made some attachments that can go on the end of the hose as well.

        years ago I had this amazing double-action floor pump, I think it was a coleman, that pushed 2L of air on the upstroke and the downstroke, and the hose was attached to the floor portion instead of the handle section so the hose didn't move around as you pumped. that filled up the 12" balloons I had at the time with frightening speed. no clue what happened to it.

        I'd really like something that's quiet, insistent, and on the slow side like an aquarium aeration or CPAP pump. There's also plans out there to make balloon pumps out of lego components, I'd like to try that as well. Someday, maybe.

        Comment

        • Mlooner101
          Member
          • Jul 2026
          • 94

          #5
          Definitely a pump expert, very impressive! 👌

          Comment

          • Thinskinned
            Look Out!
            • Jul 2024
            • 247

            #6
            Originally posted by Mlooner101
            Definitely a pump expert, very impressive! 👌
            Thanks; what I really want most of all is a pump that has juuuuust enough power to start a balloon and inflate it slowly enough to keep it expanding, like something with a pressure sensor that always has the pump running 0.2 PSI above whatever it measures the pressure inside the balloon to be or something like that. Or something that I can very easily and deliberately control the rate of inflation, I really like to draw the process out.

            I'd also like to get the chance more often to inflate balloons using dry ice or liquid nitrogen, there's something about the inflation rate being slow, uncontrolled, and not requiring any outside input thats very appealing. Sublimating/evaporating gas isn't really pump-related, though.

            Comment

            • Jup
              DIY balloon tools
              • Aug 2021
              • 43

              #7
              I've been using my own pump that I never finished based of off a modified 40mm industrial fan that runs of off a 4s lipo cell controlled by a linear potentiometer. For large balloons it's amazing due to the portability but honestly it is a hassle for anything less than a 24" balloon. Would rather have one of those cheap boxes activated by pushing on it.

              In the past I've used small aliexpess vacuum pumps as well, 3 in a series for very slow inflation. Heated dog dryer was fun as well but too powerful so once again unless you do GL700's on the regular not recommended.

              These days I would probably recommend a good reviewed electric air duster with a hose attached to it. Will get you 3/4th the way to my static pressure and inflate anything thats been pre-stretched probably with all the portability you need.

              Comment

              • Mlooner101
                Member
                • Jul 2026
                • 94

                #8
                Yeah I find that the pump I have is super powerful which has pros and cons (I don't know that actual output stats), good for massive round balloons like cloudbusters but it does make it difficult to blow up odd-shaped balloons right, kind of need a slower inflation rate for those

                Comment

                • Bloonr
                  Member
                  • Jul 2026
                  • 50

                  #9
                  I use one of those electric air dusters you get off amazon. They are much quieter than the standard electric balloon pumps imo. Ive blown up 60 balloons with it one day and it was only starting to heat up by that 60th balloon (to which is switch to using my mouth to get more). Its perfect for large balloons too. I feel those standard electric balloon pumps are too quick for blowing up balloons sometimes where my electric air duster thing has different speeds. Recently ive tried using it to pump to pop a gl500 but i usually back off before it bursts because i realise the cost of them lol. Watching it slowly inflate though is very appealing to see. Only flaw i have with mine is its button to turn on is kinda broken now but ive got my moneys worth of it (lasted over a year) and i also dont need to hide it too since i can use it for its actual purpose too without anyone questioning it

                  Comment

                  • Mlooner101
                    Member
                    • Jul 2026
                    • 94

                    #10
                    Originally posted by Bloonr
                    I use one of those electric air dusters you get off amazon. They are much quieter than the standard electric balloon pumps imo. Ive blown up 60 balloons with it one day and it was only starting to heat up by that 60th balloon (to which is switch to using my mouth to get more). Its perfect for large balloons too. I feel those standard electric balloon pumps are too quick for blowing up balloons sometimes where my electric air duster thing has different speeds. Recently ive tried using it to pump to pop a gl500 but i usually back off before it bursts because i realise the cost of them lol. Watching it slowly inflate though is very appealing to see. Only flaw i have with mine is its button to turn on is kinda broken now but ive got my moneys worth of it (lasted over a year) and i also dont need to hide it too since i can use it for its actual purpose too without anyone questioning it
                    yeah I should really get one of those, one other downside of my pump is that it is super loud. I live alone but share a wall with neighbours and they must think why I vacuum the bedroom so many times 😂

                    Comment

                    • Thinskinned
                      Look Out!
                      • Jul 2024
                      • 247

                      #11
                      so it turns out that a small aquarium pump does exactly what I wanted, pushes a tiny trickle of air at juuuust enough pressure to inflate a balloon. I think it wold probably take like half an hour to pop an 11" running on max power but I don't hate that.

                      Comment

                      • Mlooner101
                        Member
                        • Jul 2026
                        • 94

                        #12
                        Originally posted by Thinskinned
                        so it turns out that a small aquarium pump does exactly what I wanted, pushes a tiny trickle of air at juuuust enough pressure to inflate a balloon. I think it wold probably take like half an hour to pop an 11" running on max power but I don't hate that.
                        nice mate I respect the experimentation!

                        Comment

                        • cutipop
                          Junior Member
                          • Jul 2026
                          • 12

                          #13
                          Does anyone know of a small, portable electric pump?

                          Comment

                          • Atlanta Dave
                            Junior Member
                            • Feb 2020
                            • 19

                            #14
                            When we build big sets for shoots we used to use on of those dual inflators you can buy just about anywhere. Recently we switched to "XPOWER". We now use them for everything 12" and up. They have a fast and a slow setting and it is easy to handle and use. We timed it recently and with one inflating and one knotting we were averaging 4-f qualatex 16" a minute. Usually the model (in this case Alex Brylko) does the inflating while I do the knotting. It's rather quiet and on Amazon runs around $70 or so. It has a fairly long cord and isn't large.

                            Comment

                            • Mlooner101
                              Member
                              • Jul 2026
                              • 94

                              #15
                              Originally posted by Atlanta Dave
                              When we build big sets for shoots we used to use on of those dual inflators you can buy just about anywhere. Recently we switched to "XPOWER". We now use them for everything 12" and up. They have a fast and a slow setting and it is easy to handle and use. We timed it recently and with one inflating and one knotting we were averaging 4-f qualatex 16" a minute. Usually the model (in this case Alex Brylko) does the inflating while I do the knotting. It's rather quiet and on Amazon runs around $70 or so. It has a fairly long cord and isn't large.
                              I suss them out cheers!

                              Comment

                              Working...