plastic clamps/clips to temporarily 'tie' balloon necks?

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • panther42
    Member
    • Oct 2021
    • 42

    plastic clamps/clips to temporarily 'tie' balloon necks?

    I bought some e.g. potato chip or vegetables plastic bag clamps/clips, to use to temporarily 'tie' inflate balloons' necks, but pretty clearly I didn't choose well.
    While the clips squeeze tightly enough to damage the (this somewhat older I think Tuf-tex 17") neck's rubber, the balloon still loses air noticeably (about 1/3 size overnight from well-inflated).
    Any recommendations for specific clamps/clips?
    (The other thing that I use, which absolutely works well, but is more effort, is rubberized fuzzy hair bands, e.g. in the third photo; in addition to being more work, they're difficult to use, and don't work as well, an very large balloon necks).
    You do not have permission to view this gallery.
    This gallery has 3 photos.
  • BalloonerGirl
    Senior Member
    • Sep 2025
    • 165

    #2
    When I was in hs I used to work as a kindergarten assistant, and I blew up balloons for the kids. I used a sewing thread to tie them up, and that was superb.

    Comment

    • zman21
      Senior Member
      • Jun 2022
      • 136

      #3
      I use a different method but I´m not sure if this will help you... I always try to inflate the entire neck of the balloon. If a balloon is inflated like that you can perfectly "tie" the balloon by only twisting the "ring" of the neck a bit. It doesn´t twist back because of the friction. But it only works if the neck is really full...
      Another DIY idea would be a cylindrical piece of plastic that has a slightly larger diameter than the neck - you would then just have to slip the neck over it.

      Comment

      • panther42
        Member
        • Oct 2021
        • 42

        #4
        Thanks, but both of these have the same disadvantage of the hairbands that I use.
        I'm really looking for clips, which I see in various balloon videos, so I assume that there are some products out there that just work better than the particular clips that I first tried?

        Comment

        • LoonerCouple
          Junior Member
          • Nov 2025
          • 21

          #5
          The clips from IKEA work well for me. Also the ones from a local supermarket. Looks like it depends on the actual design. Try different models.

          Comment

          • archistrong
            Junior Member
            • Jun 2017
            • 7

            #6
            I just use the garden variety 1” rubber bands from your typical office supply store. Necked or not, I’ve tied everything from 11” to GL700’s and everything in between. Here’s an example. I twist the neck at the nozzle a little to create a seal, then loop the rubber band around and through itself. You can then pull the rubber band taught and it holds as long as you want! Easy to undo as well. Just about every balloon in this photo was tied that way.
            Attached Files

            Comment

            • panther42
              Member
              • Oct 2021
              • 42

              #7
              Originally posted by LoonerCouple
              The clips from IKEA work well for me. Also the ones from a local supermarket. Looks like it depends on the actual design. Try different models.
              These? https://www.ikea.com/es/en/p/bevara-...ours-00524174/

              The Ikea page doesn't show a clip open. Would you mind posting a photo of one of the clips that you find works well, please? In particular, showing the clip open, to see the inside part of the clip that presses on the balloon neck. Thanks.

              Comment

              • panther42
                Member
                • Oct 2021
                • 42

                #8
                Originally posted by archistrong
                I just use the garden variety 1” rubber bands from your typical office supply store. Necked or not, I’ve tied everything from 11” to GL700’s and everything in between. Here’s an example. I twist the neck at the nozzle a little to create a seal, then loop the rubber band around and through itself. You can then pull the rubber band taught and it holds as long as you want! Easy to undo as well. Just about every balloon in this photo was tied that way.
                Thanks, yeah, 59Balloons specifically recommends that.
                I've always wondered, though, once the rubber band is stretched tight around the rubber neck of the balloon, you mention that it's easy to un-do; I'd have expected that rubber band material pulled that tight would be very difficult to pull back through. How do you do it?

                Comment

                • Eugénie-extralooners
                  Junior Member
                  • Oct 2023
                  • 25

                  #9
                  We also have clips that will be gentle on your balloons while ensuring a secure closure! Feel free to visit our website at extralooners.online.

                  Comment

                  • archistrong
                    Junior Member
                    • Jun 2017
                    • 7

                    #10
                    Originally posted by panther42

                    Thanks, yeah, 59Balloons specifically recommends that.
                    I've always wondered, though, once the rubber band is stretched tight around the rubber neck of the balloon, you mention that it's easy to un-do; I'd have expected that rubber band material pulled that tight would be very difficult to pull back through. How do you do it?
                    It all depends on the size of the rubber band and how tight you pull it. If you want to easily remove it, use a larger rubber band and don't pull too tight. It'll still hold air just fine. I typically use rubber bands when I want to maximize the amount of neck on my balloons. I use size 16 (2 1/2" x 1/16") rubber bands and I've never had them leak air. They take a little more effort to undo when pulled tight, but isn't hard to do.

                    Comment

                    • LoonerCouple
                      Junior Member
                      • Nov 2025
                      • 21

                      #11
                      Originally posted by panther42

                      These? https://www.ikea.com/es/en/p/bevara-...ours-00524174/

                      The Ikea page doesn't show a clip open. Would you mind posting a photo of one of the clips that you find works well, please? In particular, showing the clip open, to see the inside part of the clip that presses on the balloon neck. Thanks.
                      Yes, that are the ones. They have three strips pressing down from the top between two from the bottom.
                      Make sure the neck of the balloon is laying flat between the parts for best results.
                      Attached Files

                      Comment

                      • panther42
                        Member
                        • Oct 2021
                        • 42

                        #12
                        Originally posted by LoonerCouple

                        Yes, that are the ones. They have three strips pressing down from the top between two from the bottom.
                        Make sure the neck of the balloon is laying flat between the parts for best results.
                        Hm. That looks just like the clips that I have, which definitely damaged the (okay, maybe because it was a bit older) Tuf-tex 17" balloon neck ...

                        Comment

                        • loonlun
                          Senior Member
                          • Mar 2021
                          • 410

                          #13
                          Originally posted by archistrong
                          I just use the garden variety 1” rubber bands from your typical office supply store. Necked or not, I’ve tied everything from 11” to GL700’s and everything in between. Here’s an example. I twist the neck at the nozzle a little to create a seal, then loop the rubber band around and through itself. You can then pull the rubber band taught and it holds as long as you want! Easy to undo as well. Just about every balloon in this photo was tied that way.
                          tried this the other day when one of my clips broke and I think I'll just get a bunch of rubber bands going forward.

                          Comment

                          • lucid
                            Senior Member
                            • Sep 2016
                            • 1174

                            #14
                            Yeah rubber bands are the ticket. I usually just half-knot my balloons since I can never find my rubber bands.

                            I also routinely use hi-float on my balloons and since it is just essentially glue, you can just squirt a little inside the nozzle and pinch it shut and it will be sealed off permanently, or until you break the glue seal. I usually use hot water for that. It does take a while to dry tho, so your best bet would be just to use a rubber band in either case.

                            Comment

                            • LoonerCouple
                              Junior Member
                              • Nov 2025
                              • 21

                              #15
                              I tried rubber bands yesterday and it worked perfectly. Thanks for the info!

                              Comment

                              Working...