Patching a giant balloon

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Exaturbo
    Senior Member
    • Feb 2021
    • 201

    Patching a giant balloon

    Hi all.

    hoping for some advice before I go ahead and try to patch a giant balloon I have.

    it’s a 72” “climb in” balloon. Unfortunately straight out of the bag it has a small hole near the neck area.

    I suspect that in the intended use case for this balloon it wouldn’t be an issue. But because I want to keep it inflated and around for a while, it is.

    I need to patch the hole. It’s close enough to the neck area that even once I tie it the hole leaks.

    I have rubber cement and a bit from a broken GL1200 that I can use as the patch material.

    I need to ask if the patch needs to be circular, or I can cut a small square and use that ?

    it’s in an area that won’t see much stretching from inflation.

    I do have pics but can’t post them as they are too large for the group limit.

    it would be too costly to consider trying to return it to China.
    and given it wasn’t a cheap purchase, I want to try to save it if I can


    any advice for me ?

  • cl23
    Senior Member
    • May 2022
    • 381

    #2
    Hi,
    Always clean both surfaces with isopropyl alcohol, than the shape of the patch will not have to be very precise, but round is best for equal tension around the patch:

    This is a little bit more, than a simple patch, but should show the principle:
    1.jpg

    Even a very ugly patch can be more than sufficent, if applied correctly. This one is airtight too and under very high tension:
    b2.jpg
    You can do a lot of cool things with rubber cement and balloons btw:
    k16.jpg

    Comment

    • cl23
      Senior Member
      • May 2022
      • 381

      #3
      For small pinholes, a drop of liquid latex is the easiest way:
      1.jpg 2.jpg 3.jpg
      4.jpg

      Even for larger defects, but this required 3 or 4 layers. This balloon contruction lasted as long, as a normal balloon - many weeks:
      w2.jpg

      Comment

      • Exaturbo
        Senior Member
        • Feb 2021
        • 201

        #4
        Thanks for the info / advice.

        the hole I’m dealing with won’t be under much if any tension / stretch as it’s right near the top of the neck. And under normal use for this balloon type and for its intended use, probably wouldn’t be an issue.

        because these have no rolled lip on the top part of the neck to make climbing in easier, it’s much harder to seal when inflated. The hole was close enough to the tie point that air was still escaping. I’ll have a go at patching this weekend and report back my success or failure.

        I won’t be using it for climbing in. But other “fun” activities.

        thanks again.

        Comment

        • Exaturbo
          Senior Member
          • Feb 2021
          • 201

          #5
          So. Here’s the hole and the patch. It’s a little
          rough. This is the first time I have attempted anything like this.

          haven’t yet tried inflating it. That will be a tomorrow job.
          given the location close to the top of the neck, I think it will be fine.

          (yes that’s my entire hand just casually inside the neck)
          for reference on just how big this balloon is.

          You do not have permission to view this gallery.
          This gallery has 2 photos.

          Comment

          • Exaturbo
            Senior Member
            • Feb 2021
            • 201

            #6
            It’s not the prettiest of repairs, but it seems to be working.
            quite difficult to tie up these extra large balloons. I usually use zip ties but even that wasn’t super easy with no rolled lip.

            using zip ties makes it fairly easy to remove them if deflating is needed or to add air.
            You do not have permission to view this gallery.
            This gallery has 1 photos.

            Comment

            • DJ Looner
              Senior Member
              • Apr 2020
              • 160

              #7
              I've used HH66 vinyl cement on my climb in balloons with a patch on both sides in an area that gets extremely inflated. I have a small inflatable twin size air mattress that I put inside it. It holds up great.

              Also I recommend getting the 100" climb in balloons. i normally buy a larger quantity from bubblexl.com. but balloune-qc has them too for less in canada. They are just sometimes weird about shipping to us due to trade deals etc. I have never had to cut the rolled edge off. And I always pretreat in my clothes dryer to warm it up before inflating.

              Comment

              • Exaturbo
                Senior Member
                • Feb 2021
                • 201

                #8
                Originally posted by DJ Looner
                I've used HH66 vinyl cement on my climb in balloons with a patch on both sides in an area that gets extremely inflated. I have a small inflatable twin size air mattress that I put inside it. It holds up great.

                Also I recommend getting the 100" climb in balloons. i normally buy a larger quantity from bubblexl.com. but balloune-qc has them too for less in canada. They are just sometimes weird about shipping to us due to trade deals etc. I have never had to cut the rolled edge off. And I always pretreat in my clothes dryer to warm it up before inflating.

                I’ll look into those other sources for the larger balloons.
                shipping is a big issue here. I’ve had many times where the postage is actually more than the balloons.

                this particular one came from aliexpress via china. It already had no rolled lip on the neck.
                just how it came. It did make it rather difficult to seal.

                on the plus side, the patch is holding and the balloon is still inflated.

                Comment

                Working...