Overinflating Cattex Dolls & GL 1200's

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • BalloondudeEU98
    Member
    • Jul 2024
    • 78

    Overinflating Cattex Dolls & GL 1200's

    Has anyone been able to overinflate cattex dolls & GL1200's? I dare to go slightly beyond rated size, but am definitely curious (yet scared as a non-popper) to go any further. Would love to hear your experiences!
    And a final question, I only mouth inflate my balloons and don't pop them. I blow them up several times, but am trying to store them as best as possible. Looking for any tips to store balloons to use them multiple times, keeping them in good condition. Many thanks!
  • TheBigPoolCat
    Senior Member
    • May 2025
    • 163

    #2
    I'm sure some people can go into much better detail about long term storage. But for short term restoration, make sure to find a way to reheat the late as is done a couple times in manufacturing. The easiest way is to get a hairdryer and after deflating the balloon, give it a thourogh blowing over. Don't try and inflate it with the dryer, that's a great way to make a crappy flamethrower. But the heat revulcanizes the latex most of the way.

    Comment

    • Kummelkopp
      Member
      • Feb 2025
      • 91

      #3
      As you Blow them by mouth, there will always be humidity left in the balloon, which makes them sticky on the inside.

      What I do is to use a hairdryer after to usage to get them to shrink again. And then, I put in just a little bit of air (no dtretch, only their mould shape) and seal them with a clip. This way the inside walls dont touch each other and won't Stick together...but this way requires a bit of room to Store the balloons....

      Another was would be talcum, but I have No experience in that. I guess humidity is bad overall, so drying them inside and out is even better than "my way"

      Comment

      • Hellus
        Tough Blower
        • Mar 2025
        • 182

        #4
        I overinflated a giant doll after several full inflations (more than 15 at least) and it was really stretchy at the time of its final destiny. It blew up to a massive size before the burst, but I intentionally did not blow up the head just to check if it blows up on its own at the end. It did not. But it burst when it was very tight. Did not overinflate a GL1200 yet, but definitely inflated to a good size when the neck started forming. I can say both balloons are well built and can withstand several full inflations.
        Regarding storage, after I deflate the balloons, close the mouthpieces with the clips that came the balloons and then wash them under running hot water. The latex is shrinked and the inside, which has powder, is completely dry in this manner. Then I let them dry naturally and restore folded.
        N.B. I inflate everything with my mouth.

        Comment

        • Guest

          #5
          Originally posted by BalloondudeEU98
          Has anyone been able to overinflate cattex dolls & GL1200's? I dare to go slightly beyond rated size, but am definitely curious (yet scared as a non-popper) to go any further. Would love to hear your experiences!
          And a final question, I only mouth inflate my balloons and don't pop them. I blow them up several times, but am trying to store them as best as possible. Looking for any tips to store balloons to use them multiple times, keeping them in good condition. Many thanks!
          I have tried pump2pop and normal cattex doll once, while sitting on it, Goddamn!
          Best ride ever and it got a huge neck also.
          But i tried a 3 meter doll from gummiwerks :O :O filled up the entire living room before pop

          Comment

          • LoonerHoax
            Senior Member
            • May 2020
            • 521

            #6
            I've overinflated numerous Cattex dolls. Mainly with air from a pump. I did it once with helium. That was an amazing ride.

            Comment

            • Balloonboy99
              Member
              • Sep 2019
              • 52

              #7
              I've found the best way to keep balloons stored after mouth inflation is to first shrink the balloon back down with a hair dryer, then turn the balloon inside out (this can be a bit tricky, I blow a little bit of air into the balloon, gently hold the neck then start to push from the drip point through to the mouth piece, gradually releasing air as I push. Another way is to stretch the mouth piece open and sort of push the balloon through with your thumbs. Once you get enough through you can pull it out.)

              The reason to turn it inside out is that the inside tends to fill with condensation, so once it's inside out I take my hairdryer or towel and dry off the inside completely. If there isn't much talcum powder left from the original factory coat I add a bit more, or you can use cornflour if you prefer. Then I turn the balloon back inside out again so it's the right way, and sometimes I'll coat the outside in talcum powder too to stop it sticking to other loons.

              Comment

              • BalloondudeEU98
                Member
                • Jul 2024
                • 78

                #8
                You all are amazing! Thank you everyone for your wonderful insights, will definitely try everything mentioned. Amazing little community we have here

                Comment

                • DJ Looner
                  Senior Member
                  • Apr 2020
                  • 160

                  #9
                  Those are all great ideas but if you have a clothes dryer where you live just use that. Toss them in for 5 min or as needed and done. Just don't leave them in for a full cycle. I have climb in balloons which is why I learned this. But I have done it with balloons my kids wanted to keep as well.

                  Comment

                  Working...