I made that balloon clips with 3d printer. 85 and 65 mm long.
3d printed balloon clips
Collapse
X
-
3d printed balloon clips
You do not have permission to view this gallery.
This gallery has 1 photos.Tags: None👍 3 -
It turned out to be quite reliable. I tested it in action, and it does not open by itself, but is held by a latch, especially the smaller oneComment
-
-
-
That's a really cool idea, printing these. The commercial ones can be too soft and bend in the middle, so are not airtight with some balloons.
I also love designing and 3d printing balloon accessories. I am only into 3D printing and CAD for a week now, but already managed to finish some useful things.
Below is a super lightweight (7 grams total) mouthpiece for ballons with integrated one-way valve, that opens and closes with minimum effort (thin latex membrane). You put a balloon into the front hole and it can't escape, even when you blow to pop it. Most 10" - 19" if not wide neck will fit into it. You also can attach 2 sizes of hoses to it and use it with a compressor or electric inflator:
2.jpg 1.jpg 5.jpg
This should work without glue as well, but i have to tweak the settings for pausing and continuing for inserting the valve mid print to have enough layer adhesion at that place.👍 1Comment
-
-
For sure. I attached a zip-file with both stl-files. It's a little bit tricky, but it is worth it.
You have to print the check valve first. After its done, you need a round piece of latex, e.g. from a balloon. Cut a hole in the exact center to attach it in the middle.
Then you print the nozzle. Pause the print at 15 mm. You have to insert a pause into the g-code. The perfect layer for the pause will be visible in the slicer. It is the place before reaching the 90° overhang, that will be put on top of the inserted valve.
Insert the check valve with the latex membrane pointing downwards, then continue printing, if everything lines up perfectly. I printed with 0.2 mm layer height so this would fit easily.
If it won't be airtight or falls apart, use super glue and let cure overnight, as i did.
You can also simply print the nozzle without pause, then you have a good mouthpiece, that holds the balloon.Attached FilesComment
-
This month, i started with a really old 3d printer from 2017, but now got two modern ones - a huge one and a very fast one. I can recommend Ender 3 V3. They are not that expensive and much easier to use, that old ones (automatic bed levelling etc.)
You need a slicer software, also if you only want to print downloaded 3d models. It turns the 3d model into a language, you 3d printer understands and you can influence, how it will be printed (lightweight and more fragile or massive and heavy). I am using Cura. It is free. Most 3d printer manufacturers include this software.
If you want to make own designs, you need software for that. For more organic things, like animal figurines etc. you can use Blender. For technical stuff with exact measurements, you need CAD software.
I design in FreeCAD, that is free as well. Yes, this is complicated to start with, but there are lots of tutorials. You don't need artistic skills for this, but have to work with measurements and numbers a lot. Use the videos that are not older than 6 months, because at the end of last year, FreeCAD 1.0 came out and this is the first version, that can be used relatively easily.
I learned everything about CAD and 3D printing on YouTube.Comment
-
this worked really well, for the most part -- I printed out one as a test and then a second when I figured out what I did sub-optimally the first time. I'm having some trouble getting the check valve to close cleanly, how did you cut a hole in the piece of latex to get it to seat cleanly? I used a punch and just pulled it over until there was a hole, got it to fit, then cut it to size with scissors, but it's not perfect. it will seal but can take a second or two. I suspect the hole I made was too small which causes the latex disc to warp slightly, ending up needing a little coaxing to seal properly. I also used nice thick latex from an unused Cattex 16", is there a particular source that you've found works well?For sure. I attached a zip-file with both stl-files. It's a little bit tricky, but it is worth it.
You have to print the check valve first. After its done, you need a round piece of latex, e.g. from a balloon. Cut a hole in the exact center to attach it in the middle.
Then you print the nozzle. Pause the print at 15 mm. You have to insert a pause into the g-code. The perfect layer for the pause will be visible in the slicer. It is the place before reaching the 90° overhang, that will be put on top of the inserted valve.
Insert the check valve with the latex membrane pointing downwards, then continue printing, if everything lines up perfectly. I printed with 0.2 mm layer height so this would fit easily.
If it won't be airtight or falls apart, use super glue and let cure overnight, as i did.
You can also simply print the nozzle without pause, then you have a good mouthpiece, that holds the balloon.
I then cut the part apart in my software and meshed the hose attachment bit with a fitting for one of my high-speed blowers, so I can use a 5/8 OD tube between them very easily, works a treat.
Any other designs you've come up with? hoping to see some uploads from you on YT soon, I love the part of looning that lets me engineer new and inventive ways to inflate balloons.Comment
-
longnecklover
Yes, indeed the latex part is a little bit tricky. I also punched it out, but it did not fit well, so i had to cut it with scissors. The latex must not touch the tube. It has to be abled to move freely and has to be larger, than the area with the holes, it has to cover.
I used 0.4 mm sheet latex, because i did not have much luck with cutting the pieces out of ballons. These were not really airtight. The sheet latex is perfectly flat.
Over the last days, i experienced, that it is best, to have the hole in the latex as small as possible and bend it to get it over the little thing, that holds it. That makes the best airtight seal. Putting liquid latex to seal did not work, because it pulled the latex sheet away from the bottom.
For sure there is some new design, i developed over the last weeks
On the pictures below is a modular machine, that can inflate or pump to pop 36 balloons in a row, each 10 - 19" so enough to fill a small room. It always inflates the balloon at the lowest position, then a motor pushes it out, drops it on the floor and the next one comes into play. They all sit on an extendable rail. Every balloon is attached to a modified super lightweight version of the check valve you printed and keeps its air, after being inflated and is secured by a ring, so it can't get off the valve when being pushed to or over the limits.
I hope, the machine gets finished and ready to use tonight. For it i had to design more than 30 different parts in CAD and most had to be redone over and over until it worked, but today, it was the first time, it inflated 36 balloons in a row (on the 3rd picture with small 11" balloons from a few days ago are less balloons - i extended the machine to the capacity of 36 balloons afterwards).
For sure i spent more than 100 hours to design and build this, but i love this machine so much. I press only one button on my wireless controller and 36 ballons will be inflated fully automatic or it inflates one single balloon, whenever i press the button.
It works best together with my hi-tech programmable balloon inflator (i can specify the amount of air or pressure for each balloon, every next balloon one liter more than the last etc.), but it needs no electronic communication. It holds a balloon, until there is a pressure drop (inflator stopped), than the next one will be loaded. Theretically, you can inflate the balloons by mouth, but every balloon would only get the amount of air, that is the volume of your lungs, except you can breath out constantly like some brass players
There will be new videos on my YouTube channel soon.
9.jpg 7.jpg 8.jpg😀 1👍 1Comment
-
I have a question....I found a balloon clip for 8 balloons you would hang down from the ceiling and it looked really neat, but when I ordered it they pretty much ignored me, so I got my $ back. I've seen some smaller 4 or 5 flower clips on amazon....but when you can double that- I can't find it anywhere else. Have you tried anything like that?Comment
Comment