Ain't nothin' like baked loon

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • The Masked Looner
    Senior Member
    • Nov 2024
    • 179

    Ain't nothin' like baked loon

    I was just blowing up some baked 18" pearlescant Tongxuan balloons, they get pretty huge on 2nd and 3rd inflations. In the 2nd picture is a non baked 18" pearlescant Tongxuan balloon on the right and a baked one on the left for a size comparison.

    SAM_0314s.jpg SAM_0300s.jpg

    That biggest one was able to hold the weight of my feet resting on it for a few seconds, before it went FTHWUUUMPP!!!

    I just love baked loons.
    Last edited by The Masked Looner; 10-10-2025, 12:11.
    Looning since 1989

    To see my pictures of prints and blown up examples: Printed Balloons - Balloon and Inflatable Fetish Forum​
  • FunLooner
    Senior Member
    • Dec 2019
    • 877

    #2
    Wish I could figure it out I would really like to explore it

    Comment

    • The Masked Looner
      Senior Member
      • Nov 2024
      • 179

      #3
      Originally posted by FunLooner
      Wish I could figure it out I would really like to explore it
      I'm planning on making a tutorial topic eventually.

      The best advice I can give right now is that a big key to success is even baking, an unevenly baked balloon (part of it is thick and stiff, and the other part of it is thin and stretchy) will likely pop really early on in inflating before it even gets to a quarter of it's rated size, balloons can't seem to handle the inconsistency. I'm sure that preheating the oven, using the fan, lower temps for longer times rather than higher temps for shorter times, and having the balloons in the middle (I have them sandwiched between two pieces of baking paper on the metal rack/shelf) bakes them more evenly. I have the most success with evenly baked balloons, getting them way past their rated size and they can still handle some light abuse.

      Also, with a lot of balloons the necks will be a lot thinner and stretchier than the main body, and this can be the weak link in the chain and lead to premature bursting after baking when you inflate them, so I will tuck the necks into the main bodies which protects the necks from the heat a bit and they don't get as baked, and it also makes more room for more balloons on the baking paper.

      As for temps and times, it can vary a lot from brand and size of balloon. I'll give some temps and times for certain brands and sizes in the tutorial topic.
      Last edited by The Masked Looner; 23-12-2024, 18:32.
      Looning since 1989

      To see my pictures of prints and blown up examples: Printed Balloons - Balloon and Inflatable Fetish Forum​

      Comment

      • lucid
        Senior Member
        • Sep 2016
        • 1174

        #4
        Wowee that is some impressive results! I've tried baking before and I'm pretty sure my balloons did get a little bigger than usual but I'm not sure if they actually got bigger because of the baking or if it was just because I had the confidence to push them further because they were baked.

        Yeah if you wouldn't mind to explain your technique that would be super awesome. I'd bake all my balloons if they turned out like yours haha.

        Comment

        • nonpop
          Soft balloons first
          • Jul 2024
          • 104

          #5
          I also do this all the time - highly recommended if you like soft, thin balloons.

          I have them straight on paper in the oven between 100–130ºC. If you go 100ºC for most brands you'll need about 2 hours in there. That will bake them evenly. The weird thing though is that more or less nothing will happen before 1h 45 mins on that temperature. And if you bake them just 10 minutes too long, they'll be too soft and won't handle pressure later. You'll need to do some experimentation with different brands (and even sizes).

          If you go 130ºC it will only take like 5-15 minutes, but with a bigger risk of uneven spots. And likelucid says, will break them.

          Comment

          • Loonerloon99
            Junior Member
            • Sep 2021
            • 11

            #6
            I wonder... What about sous vide? You can set the temp exactly where you want it and get uniform coverage? I don't know if anyone has tried? I also have a technique of using the hottest water out of my tap on a balloon when it is deflating after inflating it. It seems to help increase the stretchiness on subsequent inflation. I'm going to try sous video sometime this month and post back.

            Comment

            • bigloonfucker.cz
              Punk member
              • Nov 2023
              • 145

              #7
              Yes, that's what i do with every balloon. I use 140 to 150°C 5mins approx. Sadly bigger than 45" can't fit my oven. But the smell during baking is terrible. Ventillation needed. And the feeling of baked stretched balloon is undescribeable. The old hard balloons can be treated as well without losing durability
              The softer balloon the better. When not soft enough, I bake him untill success

              Comment

              Working...