Trying to understand balloon care terms

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Hazloon24
    Senior Member
    • Jun 2023
    • 150

    Trying to understand balloon care terms

    Hi all,

    I am wanting to learn more about what it means to "bake" balloons, or even boil them?

    What does this provide, and what are the inherent benefits or negatives? Does it improve their longevity, stretchiness? Can it affect their integrity if done incorrectly?

    Also, I have heard of people putting balloons inside dryers, etc.

    Is there any risk of the latex melting during these? Or is the melting point of the latex much greater than I am estimating.

    I hope that I can maybe even utilize some of these methods!

    Thanks!
  • The Masked Looner
    Senior Member
    • Nov 2024
    • 179

    #2
    I tried boiling balloons on several occasions many years ago and it did nothing to them.

    I've been trying baking for a while now and I've had some success and some failures.

    I'm not sure if it improves their longevity, but if done correctly they become much softer, stretchier, and will get way bigger. When they pop it's not as loud either.

    Yes, there is definitely a risk of the latex melting if they're baked for too long. They can become like gooey bubble gum which makes them useless.

    What I have found is that the temp and time for one type of balloon wont necessarily be correct for another type of balloon. For example you might figure out a temp and time that bakes Qualatex 16" loons perfectly, for another brand of 16" loons, or even a different size of Qualatex, that same temp and time may melt them, or it may barely do anything to them.

    Also, it seems that a lower temp for a longer time will bake the balloon more evenly than a higher temp for a shorter time. When a balloon get's baked unevenly it means parts of the balloon will be weaker than others, and other parts will be stronger than others. It seems this unevenness makes a balloon more prone to popping before it's fully inflated. As I've tried inflating uneven baked balloons where they didn't seem too weak anywhere, yet they still popped when they were around half way of being inflated. And I've had other baked balloons which were baked more evenly and they were way thinner and weaker, yet they got quite a lot bigger than their rated size.

    Out of everything I've tried so far, what I've found works the best is to have the oven pre-heated, no fan, and once the oven is hot enough just put the balloons between two pieces of baking paper and put them on the wire rack in the middle of the oven.

    I've also found that the necks on some balloons can be a very vulnerable part after baking, and so when inflating I will hold the neck so the rest of the balloon inflates, and then I can let go of the neck and let it inflate a bit and it'll be fine. Otherwise it'll just be the neck that will mainly inflate and then pop before the rest of the balloon inflates.

    Here's an example, I have found that putting Tong Xu 18" balloons, and those balloons on UK Amazon (https://www.amazon.co.uk/dp/B0942XKR...fed_asin_title) which are advertised as 24" (it seems that they're more like 18") into a preheated oven for 15 minutes at 140c, no fan, bakes them perfectly for me.

    But I tried Tong Xu 36" balloons with these same settings and time, and they baked unevenly, they popped before they were even half way inflated. So it looks like I need to try a lower temp and longer time for these.

    Also what I've found helps when things don't work out is to tell ChatGPT about it, it'll give me advice like for example, make sure the oven is preheated as that will contribute to even baking, and it'll give me times and temps to try. You can try some of it's advice, if it doesn't work, tell it about and what the results were, you can both keep narrowing things down until you find something that works. It's totally worth it if you like giant, soft, thin balloons.
    Last edited by The Masked Looner; 22-11-2024, 00:42.
    Looning since 1989

    To see my pictures of prints and blown up examples: Printed Balloons - Balloon and Inflatable Fetish Forum​

    Comment

    Working...