Customizing pumps/making valves

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Hazloon24
    Senior Member
    • Jun 2023
    • 150

    Customizing pumps/making valves

    Hi all,

    Does anyone have any advice on where to buy one way valves?

    Also, has anyone ever modified or added valves on to pump pipes?

    I have been thinking about this, as the pump I have tends to let air go if its left to rest, not fast, but it is annoying.

    Thanks!
  • stretchedtight
    Senior Member
    • Apr 2013
    • 275

    #2
    Photos of the pump you have may help with guidance. I've made some recommendations on one way valves on here before, but it would depend on your situation. I use these valves and have put on the end of a pump and it allows me to over inflate a balloon and turn the pump off and leave the balloon inflated. https://serfinitymedical.com/product...x-medical-1664 (ignore the price - that is for a case of 50 and still really high priced. I've been able to find them for about $1 each)

    Comment

    • Non_Pop
      Junior Member
      • Nov 2022
      • 2

      #3
      If you go to the home center stores, look in the sump pump section for PVC one way check valves. They are available in 1" - 2.5" versions. Those along with the rubber/vinyl couplers used to attach to the pipe can match various size balloons. I have a few and even have connected them to 18" to 72" balloons.

      Comment

      • cl23
        Senior Member
        • May 2022
        • 381

        #4
        stretchedtight
        Where did you get one way valves for a dollar each? I'd be highly interested to buy a few dozens of them for things i do like this:


        This only works properly with check valves on each output, but the ones, i used, are very small and make loud noises (i filtered the audio in the video, so it is much less audible).

        For my electronic inflator, i bought a big brass check valve at the hardware store (highlighted in the picture):

        inflator valve.jpg
        The advantage is, that it won't melt, when used for longer periods of time with a powerful electric blower. This big one won't affect the airflow.
        The disadvantage is, it is heavy and the spring inside was too tight, so i had to shorten it, so the motor can run on very low speed and the valve still opens.

        Comment

        • Gunnapop
          Senior Member
          • Oct 2020
          • 215

          #5
          cl23 - what is the control board for? It also seems like there may be a heating unit in there as well. I am trying to figure out how to integrate a heater into my frankenblower...but, need the controls to go to standby blowing so the heating coils don't burn out. The plumbing is another issue. Flex metal air lines at a decent diameter are not cheap...no easy to come by. I have some flanged vac lines from my old neon shop and have to proto-fab with them somehow. ~gp

          Comment

          • cl23
            Senior Member
            • May 2022
            • 381

            #6
            The control board is an Arduino Mega with about 10.000 lines of code in software. It controls the motor (speed adjustable in 0.1% steps), 4 solenoid valves for 2 separate outputs (inflation and deflation for each output) and a temperature controlled fan. Connected are 2 pressure sensors, a mass airflow sensor and a temperature sensor. It is controllable by using a smartphone app (bluetooth), a wireless PS2 controller, via USB or hardware buttons. It can run complex programs for torturing balloons or simply inflate all balloons to the same size, measure all kinds of stuff, show diagrams or it wakes you up at 6 a.m. by popping balloons if you want it to

            The blower motor contains a heating, but i do not use it, because i don't feel the need for it. For safety reasons, it is not connected (wouldn't be a problem with a second TRIAC circuit). The motor cools itself by outputting air, so the air gets up to more than 50 °C after a while without the heating. At first, i used 90° plastic pipes directly at the output of the blower motor, but they deformed heavily after a while, so i replaced them with copper parts. After the airflow sensor (black) and the brass check valve, the air is cool enough for regular clear PVC tubes.

            Comment

            • Unicks
              Senior Member
              • Nov 2020
              • 103

              #7
              @cl23: Never thought anyone else would go to this extent at an inflator... I've gone down a different road, but use what you have right? I have a system that uses a single servo valve controlling venting and fill, no heating on the output because of software and flow prediction issues. The inflation flow was modeled to mimic human capabilities from minimal flow at any pressure to maximum flow accurate to 10ths of a liter. I originally started this project to map the pressure and flows a balloon could take repeatedly and repeat the results.. then it became a bit of a toy, right now it's been having parts redesigned with 3D printing.

              I'm not a real big Arduino fan, but I have other C++ IDEs with various processor/mpu personalities. I've never crossed the app divide for android or apple mobile devices, so app's for controlling anything is limited to java web interface applets through a wifi-soc used to control the inflator itself. Cheap, extremely high integration and very low power.. but who cares about all that if it's plugged in.

              Attached is a 3D printed flow sensor, better than a regular hot-wire/thermistor setup because of the possibility of contamination breathing through it etc.. I can precisely measure any gas flow through it at varying pressures, but is tweaked to our Nitrogen/Oxygen atmosphere. Even the stream's temperature and relative humidity are taken into account for calculating flow.. 3D printing has made big advances to small scale prototyping. Inflator nozzles, pneumatic assemblies that can not be machined in one piece, if I need more accuracy, I print the object and machine off the extra with a metal lathe.

              IMG_20241109_1205506.jpg IMG_20241109_1206352.jpg IMG_20241109_1209316.jpg
              U

              Comment

              • stretchedtight
                Senior Member
                • Apr 2013
                • 275

                #8
                [QUOTE=cl23;n176102]stretchedtight
                Where did you get one way valves for a dollar each? I'd be highly interested to buy a few dozens of them for things i do like this:


                Don't recall - but here's a couple of examples... for $0.50 each. With shipping probably closer to a dollar. Need to buy them in a case of 50 to get that price. https://www.discountcatheters.com/me...-one-way-valve

                https://www.wholesurgical.com/medlin...e-way-valve-ea $0.79 each


                Comment

                • cl23
                  Senior Member
                  • May 2022
                  • 381

                  #9
                  Unicks
                  There are not many people out there, who do complex balloon inflators as we do
                  It took me hundreds of hours over the years but i've been using the device every week since 2015, as i started, building it. Every once in a while, it gets new functions, sometimes new hardware (it now has a ultrasonic sensor, to stop inflation, when the neck of the balloon is fully inflated, which replaces the former mechanical switch).

                  I used temperature compensated sensors for airflow and pressure. Measurements otherwise are useless with a 500 W blower motor, that puts out plenty of heat after a while. I also had to take care of turbulences in the airflow when measuring pressure during inflation with hardware and software compensations. That is a very big issue, when working with airflows that high (makes measurements switch between 10 and 100 mBar every few milliseconds, so unusable).

                  My inflator also contains functions to regulate the airflow independently from the pressure. This is possible with the airflow meter.
                  I also use the inflator to repeatedly inflate balloons to get them as bis as possible. After each inflation, the device can shrink the balloons by blowing warm air at them. That makes a lot of a difference when maximizing size and i don't have to touch the balloons or use my breath for that anymore.

                  I made a smaller portable version of the device with much less power. It is very quiet and can be used with every 12V supply, e.g. in the car.

                  onemoreblow
                  The airflow meter, i used is an automotive part. Nohting else i found was large enough or usable for cold and hot air and up to about 500 liters per minute. Hence, there is no public datasheet so i had to use a similar method for writing an algorithm, that converts output voltage of the sensor to liters per minute.
                  You can use another calibrated airflow sensor for calibration of a new one, but where to get one?
                  I used a modified inflatable beach ball for calibration. It has a known volume and i made the inflator always stop the inflation at a specific pressure. I took about 100 measurements at different motor speeds, put it into Excel and derived a characteristic curve.

                  This was not the perfect calibration method, but we are only inflating balloons, so +/- 3% is not that much of an issue. The measured values all may be off by that amount, but are always the same, as when i calibrated it years ago, no matter if 10°C or 50°C air temperature from the blower motor. It is designed for the engine of a car, so it has to be abled to handle rough conditions, must output reproducible values and last for many years. BTW, it was very cheap as a used part.

                  There is always backpressure, the more airflow, the higher, even when there is nothing attached to the outputs of the inflator, so there is a software compensation for that, that can be callibrated automatically. I need to do that, whenever i attach a hose or adapters to the inflator. It only takes a few seconds (it ramps up the motor speed once from 0 to 100% and takes measurements). Everything that affects the airflow, also affects the pressure measurements. Now i can use 5 meters of pipe from the inflator to the air outlet at the ceiling of the room without any issues.

                  stretchedtight
                  Thank you. I am living in cenctral Europe and did not find a distributor that sells this part.
                  I bough these ones and hope, they do the work too:

                  Comment

                  • cl23
                    Senior Member
                    • May 2022
                    • 381

                    #10
                    onemoreblow
                    No problem
                    My construction after all works absolutely fine and precise enough. I am not planning to fly to Mars with it, so it does not have to be perfect. It is about having fun, reproducibly and for me it has to be reliable. It never failed in almost 10 years.

                    Getting the airflow sensor to work was only one weekend of work. For sure, i kept the original housing and honeycomb grid on it.

                    I am measuring the pressure inside of the inflator, not in the balloon and would never want to put something with an attached cable inside the balloon for better measurements. A balloon has to be attached to the inflator in one second with one hand (i've build a special adapter for this, so the balloon cannot escape, even when pumped to pop).

                    My pressure measurements also are very accurate, when i compare the corrected pressure while inflation and after i switched the blower to the other output, so immediately no airflow on first output (That takes less than 0.1 seconds).

                    For back pressure, i have a software compensation, as i wrote. I reduced noise of pressure measurements heavily by simple putting some wadding really tightly into the hose that goes to the pressure sensor. The rest is done in software by always taking 5 measurements and calculating the average.

                    Good enough (Pump to Pop of a Belbal 11 inch, y axis is pressure in mBar):

                    Belbal B95.png

                    Comment

                    • S2Plooner
                      Junior Member
                      • Jan 2020
                      • 21

                      #11
                      the best one way valve I've got so far

                      Comment

                      • stretchedtight
                        Senior Member
                        • Apr 2013
                        • 275

                        #12
                        great thread. I really want to build a controller that mimics the water balloon carnival race game but uses a laser tag gun or even better a projection style game where you shoot at virtual targets that slowly pump balloons as you get points. Unfortunately I don't have the skills nor time for all the complex controllers and was looking at very, very basic solutions that triggered a momentary switch when a laser light hit it. This could control a 120v relay turning a pump on.

                        Comment

                        • Dust of the Saturn
                          Stretched like space-time
                          • Feb 2018
                          • 411

                          #13

                          Mine look like this:

                          They are called : 12 mm plastic check valve. If using imperial, then it's 1/2". They are good for anything 14 inch and smaller. You can use them for 16-18 inch balloons too but it may take a while to inflate one since the air flow is not the best. The only advantage these have going on for them is their availability on amazon which means next day delivery. Other than that, there are better options out there.

                          image.png
                          Stretched like space-time

                          Comment

                          • cl23
                            Senior Member
                            • May 2022
                            • 381

                            #14
                            stretchedtight
                            For a minimalistic solution, i would only take a photoresistor on a small battery, a solid state relay or ready made relay circuit and the electric pump, maybe a trimmer for adjusting the sensitivity. (I assume, you know, that 120 V may kill you, if you are not very careful and exactly know, what you do.)

                            loonerfun00
                            Uh, they are 5 Euro each on Amazon and too small for my purposes (hundreds of liters of air per minute).

                            Comment

                            • Slow DeFlaite
                              Senior Member
                              • Apr 2023
                              • 314

                              #15
                              I use an Intex "Double Quick 3" hand pump. It inflates in both directions up & down until the Balloon gets rock hard. It has a check valve in it already to keep air from blowing back out of the pump. You can find them at Walmart in the air mattress section for $10. I can easily inflate "36 tuftex balloons in just a few strokes. It comes with interchangeable inflator tips for excercise balls, pool toys and sporting balls.

                              Comment

                              Working...