Balloon Ace Cattex order - is this normal?

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Katiniki
    Junior Member
    • Aug 2024
    • 2

    Balloon Ace Cattex order - is this normal?

    Hello there.
    Two weeks ago, I bought a sizable bunch of 'quality' large balloon for the first time (totaling around 60£). I saw Balloon Ace listed as 'trusted' distributor, and so made an order with them.

    Today, my order arrived, but there is some unexpected strangeness .
    For one, every single large balloons in it arrived *very* dirty.


    Secondly, when I tried inflating some of them, they felt very tight and seemed to stretch unevenly. Cattexes is a new experience for me, so I don't know what is 'normal' (only cheap no-brand local ones before).
    Here what one gl500 looked like after single not full inflation. Is this pattern of uneven inelastic stretching normal for them?


    I apologize if what I'm asking is obvious, it's my first time with large 'quality' balloons, balloon ace, and Cattex. As an extreme non-popper, what I'm seeing is sending me strong red flags. I would be very grateful of someone with experience could clear things up, thank you.
    ​​​
  • Dust of the Saturn
    Stretched like space-time
    • Feb 2018
    • 411

    #2
    I have no experience with giant balloons like these but the white stuff could be talc and those wrinkles you see are most probably a result of uneven heat shrinking. This happens more commonly with dark colored crystal balloons. Also happens if you place your fingers on a deflating balloon, the heat of your fingertips will shrink a spot more than another.

    You can replicate this shrinking phenomenon by inflating a crystal burgundy tuftex or crystal purple tuftex to a very tight size and then letting it slowly deflate. While it's deflating, touch it with your fingers. It will start "hugging" them by shrinking around them faster than in other paces. Not all balloons do this, but the ones that do, in my experience, have had the best feeling latex.

    As for the white stuff, it should make your fingers frictionless and smooth if it's truly talc powder residue.

    I'd wait for other people's opinions as well.
    Stretched like space-time

    Comment

    • Frustrated blower
      Member
      • Dec 2021
      • 48

      #3
      That stretching is totally normal. If it makes you nervous, you can always run the balloon under some really hot water after inflation, and it will shrink back to a "normal" look.
      If memory serves, when you inflate a Cattex, it will be a bit stiff, but unless there is a flaw, they will inflate right up until you start to really feel pressure pushing back on your lungs. Don't push much farther past that pressure. Some brands, you can safely push farther once the pressure builds, but I've found that Cattex, that pressure is close to the limit.

      I hope this helps. Another thing is to find b2p videos of each one you have, and that will give you an idea of the limits and what to look for when they're at their limit.

      Comment

      • Katiniki
        Junior Member
        • Aug 2024
        • 2

        #4
        Thanks for the responses!
        I've played around a bit, and haven't had any pops, despite balloons feeling very tight. Seems like Cattexes are intended for pressure/tightness that is way beyond no-name balloons I'm used to. Still feeling a bit uncomfortable, as all the tells I'm used to having scream at me 'this is too far!' from the get go - but that also makes it exciting in a novel way.

        Good call on hot water treatment - when put under hot water, stretched loon immediately shrinks right back almost to its original size, with increase being what I would normally expect. I tried that with no-name balloons previously, and it didn't seem to do much of anything - but with large Cattexes, effect is dramatic and instantaneous.
        Curiously, it seems to be dependant on balloon type - 32 longneck and gl500 stretch a lot and reform right back under hot water. But 32 standard and 19 standard behave more like balloons I'm used to - not needing hot water, and the water not having much of an effect. But they are still waaay tighter than what I'm used to.
        ​

        Comment

        • grizzleylooner
          Senior Member
          • Aug 2023
          • 158

          #5
          Cattex seem to use two different latex formulas (or they buy some of their balloons from another manufacturer)
          All their smaller balloons up to 19", and the 32" pleated rounds are similar to other manufaturers latex.
          All the giant balloons made on paddle formers (including the 30") are a much thicker latex which behaves differently.
          I find their thicker ones will inflate way past rated size and still be very robust, but are very stretched when deflated although this doesn't affect their strength when reinflated. GL500 for example I'm sure are supposed to be 12" x 60" but they easily got to 16" x 70" on first inflation and still take my 110kg bouncing around on them!
          The white powder as saturn said is talc or similar. There's some on all the giant cattex, but not usually quite as much that.

          Comment

          • Guest

            #6
            Use a hair dryer to shrink it back to pre inflated shape and size

            Comment

            • Unicks
              Senior Member
              • Nov 2020
              • 103

              #7
              I've found that cattex balloons need to be fully inflated first, especially the GL's or figurines... If you inflate a GL half way and chicken out and deflate it and store for a length of time, it won't inflate properly no matter what you try. Their latex is very good quality and shouldn't be a concern. The "dirt" found on the larger cattex balloons is some of the residue from the last hot dip and wash, nothing worry about either.

              U

              Comment

              Working...