How do you keep balloons attached to a pump while they're being inflated?

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • temp893
    Junior Member
    • Apr 2024
    • 8

    How do you keep balloons attached to a pump while they're being inflated?

    I have recently purchased a variety of balloons and pumps. When I inflate any of the balloons I bought, they either leak the air back out faster than the pump can inflate them, or they don't inflate at all as the air escapes immediately; somehow every single balloon I bought has a neck that is wider than any of the nozzles on the pumps (a few are even twice the size of said nozzles!?).
    I have a bit of nerve damage with my hands (long story), so I can't really keep a grip on the necks of the balloons for long before my hands start hurting or going numb. I tried using various things to hold them in place (tape, bag clips, "balloon clips"), but nothing seems to work for long (doesn't help that the "balloon clips" don't have any instructions). The only things I have managed to successfully inflate so far are some 9-inch latex balloons and a small beach ball. (it has one of this plastic valves that makes it hard for unintentional deflation to occur.) I have spent all of my on-hand cash I got for Easter on all of this, and the results have been demoralizing.
    Am I missing something? Is there something else I can try to use to hold the balloon necks closed and in place? I tried to search online, but all I get instead are either ads for balloon clips, or the same "How-To" procedure that has been copy-pasted onto several websites that assumes the end-user has the same dexterity as the average person (The "just hold it in place with your hands and squeeze until you are done" method).
  • Guest

    #2
    Youre looking for a one way air valve. Helium balloons that are given out at events uduslly use these. Balloons come stretched over the valve, and the air gets put through the hole in the bottom of the valve and doesnt come back out.

    these are for standard 12 inch:


    however, looners have created a demand for larger ones! Only place i know of that do em for large balloons iz this.


    to go totally hands free: get lots of tape and carefully tape the valve to the end of the nozzle you choose. Then it the only interactions are slipping it on, and then pinching it off after inflation.

    Comment

    • lucid
      Senior Member
      • Sep 2016
      • 1174

      #3
      Use a rubber band to strap the balloon to the nozzle. Also if your pump is having trouble inflating the balloons, make sure you give them a very good stretch beforehand. Then as you're blowing it up with the pump, stretch the balloon lengthwise as you do it. It will usually cause the balloon to start inflating if it was giving you trouble.

      Comment

      • Dust of the Saturn
        Stretched like space-time
        • Feb 2018
        • 411

        #4
        Have you tried using a string to strap the balloon on the nozzle? you can learn a few types of simple knots to help you out. Hopefully you have enough dexterity in your fingers to tie knots. You can cut rubber bands and use them. The advantage of rubber bands is the friction which makes things tighter. Or you can look for thin and strong strings.

        If you can't use your fingers, your best bet would be an attachable one way valve. Depending on the pump, you may have to craft it yourself.

        If you want to give yourself some leverage to ease things up, try attaching or gluing a PVC tube to the nozzle of the pump. The extra length will give you more surface area to strap the balloons using old fashioned zip-ties or similar product. It will be easier handle as well.

        image.png image.png
        image.png



        The final product looks something like this:
        image.png
        ​​ ​
        Stretched like space-time

        Comment

        • srob2
          Senior Member
          • Dec 2017
          • 552

          #5
          The ring from a popped balloon works great, so does tape. I like putting a balloon on a pump, especially an electric one, with nothing to hold it. Usually it gets huge and then flies around the room, but sometimes it bursts and you don't really know which.

          Comment

          • temp893
            Junior Member
            • Apr 2024
            • 8

            #6
            Originally posted by OnceYouPop
            You're looking for a one way air valve. Helium balloons that are given out at events usually use these. Balloons come stretched over the valve, and the air gets put through the hole in the bottom of the valve and doesn't come back out.

            these are for standard 12 inch:


            however, looners have created a demand for larger ones! Only place i know of that do em for large balloons iz this.


            to go totally hands free: get lots of tape and carefully tape the valve to the end of the nozzle you choose. Then it the only interactions are slipping it on, and then pinching it off after inflation.
            Thank you for the suggestions! Regarding the link from "thinkingtoys.ie", do they ship to the United States (where I live)? I think I might know a way around the currency difference, so I should be fine on that part. As for the link from "balloonsupply.zone", I think I'll get one of each of those once I get enough spare cash to afford the additional shipping cost (~$30 per item). I will try the tape suggestion; I have a feeling that I should have tried using more tape like you are suggesting.

            Comment

            • temp893
              Junior Member
              • Apr 2024
              • 8

              #7
              Originally posted by lucid
              Use a rubber band to strap the balloon to the nozzle. Also if your pump is having trouble inflating the balloons, make sure you give them a very good stretch beforehand. Then as you're blowing it up with the pump, stretch the balloon lengthwise as you do it. It will usually cause the balloon to start inflating if it was giving you trouble.
              I forgot that rubber bands were a thing, lol. I will try that next time if I find any in the house. I do stretch the balloons before inflating them, I remember reading something years ago where it showed that made a difference in inflating balloons. I didn't know about stretching them out lengthwise during pumping though, so I will try that out next time.

              Thank you for the suggestions!

              Comment

              • temp893
                Junior Member
                • Apr 2024
                • 8

                #8
                Originally posted by Dust of the Saturn
                Have you tried using a string to strap the balloon on the nozzle? you can learn a few types of simple knots to help you out. Hopefully you have enough dexterity in your fingers to tie knots. You can cut rubber bands and use them. The advantage of rubber bands is the friction which makes things tighter. Or you can look for thin and strong strings.

                If you can't use your fingers, your best bet would be an attachable one way valve. Depending on the pump, you may have to craft it yourself.

                If you want to give yourself some leverage to ease things up, try attaching or gluing a PVC tube to the nozzle of the pump. The extra length will give you more surface area to strap the balloons using old fashioned zip-ties or similar product. It will be easier handle as well.

                image.png image.png
                image.png



                The final product looks something like this:
                image.png
                ​ ​
                I can do some knots, not many, but I can do a few. These are some good ideas, I will write them down for future reference.
                Thank you!

                Comment

                • temp893
                  Junior Member
                  • Apr 2024
                  • 8

                  #9
                  Originally posted by srob2
                  The ring from a popped balloon works great, so does tape. I like putting a balloon on a pump, especially an electric one, with nothing to hold it. Usually it gets huge and then flies around the room, but sometimes it bursts and you don't really know which.
                  You have a point about the ring thing. It's kinda like a rubber band now that I think about it. I will try that out when one of the balloons I use eventually pops from wear and tear, or something. Thank you for the suggestion!

                  Comment

                  • temp893
                    Junior Member
                    • Apr 2024
                    • 8

                    #10
                    Originally posted by OnceYouPop
                    however, looners have created a demand for larger ones! Only place i know of that do em for large balloons iz this.


                    to go totally hands free: get lots of tape and carefully tape the valve to the end of the nozzle you choose. Then it the only interactions are slipping it on, and then pinching it off after inflation.
                    Okay, I managed to get two out of three of these, but there is a problem. The end of the valve that you put the hose in is too wide for anything that isn't the end of an electric pump. While I do have an electric pump, it is very loud, so I would like to avoid using it if I can. Is there anything I can get or make that can act as an adapter for them to fit onto smaller things like bike pumps, hand pumps, or PVC tubing?

                    Comment

                    • Thinskinned
                      Look Out!
                      • Jul 2024
                      • 247

                      #11
                      For bike pumps, air compressors, etc. these guys:



                      Also available on amazon

                      You could get a rubber band to really hold one onto there, too. If the nozzle is too big for the business end or you just need a tighter grip

                      Comment

                      • NEKOCC
                        Member
                        • Mar 2020
                        • 81

                        #12
                        A rope with elasticity could be a choise. Remove the rope from the old mask and tie balloons to the pump.
                        Or you need some check valves and a suitable thickness of pipe. I bought 50 pcs check valves from Aliexpress and modify a hand pump
                        Pic 1: Check valve. You need blow from the small side. Some valve does not work and need to repair, remove the soft plastic components, cut off all burrs on the components, then re-assemble back.
                        Pic 2: Tie valve to pipe, this pipe is a part of my hand pump. You can use various materials to connect valves and pipes together, as long as there is no air leakage. I used a lot of balloon pieces and tape.
                        Pic 3: This kind of check valve is designed for 8-12 inch balloons. As you can see, the white Neo 12 balloon can use the valve directly, but the orange China 24 inch flat balloon must use a rope.
                        Pic 4: These valve can be plugged together. So you needn't to tie balloons to the valve bound on the pipe. We can prepare many balloons and then blow it.
                        Pic 5: Let's have fun with balloons.
                        Attached Files

                        Comment

                        Working...