Weak spots on balloons

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Hazloon24
    Senior Member
    • Jun 2023
    • 150

    Weak spots on balloons

    Hi all,

    Still on my quest to improve my knowledge about the balloons I use and to make my experience better. I am wondering if the photos attached have balloons with weak spots, as I am worried about unexpected pops, especially with the green 17" TT.

    I had blown the green one up to full size with a neck, and I was admiring it as it was the biggest balloon I have managed to neck so far, when I noticed the spot I panicked and let it down as I was not wanting it to pop suddenly.

    Same goes for the red one, and I am simply trying to improve my knowledge of whether these are weak spots, or simply part of the balloons texture. The red one might be difficult to see, but it looks like a grey-ish spot.

    Thank you!

    red.jpg
    green.jpg
  • lukmanrewa
    Senior Member
    • Jun 2012
    • 491

    #2
    That's a church window, it happens and are generally safe especially with high quality branded balloons like Tuftex

    Comment

    • BusterBill
      Founder, Balloon Buddies
      • Nov 2016
      • 292

      #3
      It can occur when the dye in the latex hasn't been completely dispersed. In that case the latex is just as strong as the colored portion of the balloon. So nothing to worry about.

      But there are other causes of color voids, such as a contaminated mold, which do cause weak & vulnerable spots.
      ​​​​​.
      With a bit of experience you'll be able to easily tell one from the other.


      ​​​​
      ​​​​​​



      ​​​

      Comment

      • O'Dragon
        Senior Member
        • Jan 2024
        • 298

        #4
        Would also say don’t worry. Had some like these on new rifco 40‘s and panicked as you did but later I just went for it and they held up perfectly. Best rides in a long time!

        Comment

        • Hazloon24
          Senior Member
          • Jun 2023
          • 150

          #5
          Originally posted by Casey88
          That's a church window, it happens and are generally safe especially with high quality branded balloons like Tuftex
          Thank you! I was concerned that it would go, but it is good to know that it is not something to be worried about. The red is a belbal so I assume I do not need to worry about that either.

          Comment

          • Hazloon24
            Senior Member
            • Jun 2023
            • 150

            #6
            Originally posted by BusterBill
            It can occur when the dye in the latex hasn't been completely dispersed. In that case the latex is just as strong as the colored portion of the balloon. So nothing to worry about.

            But there are other causes of color voids, such as a contaminated mold, which do cause weak & vulnerable spots.
            ​​​​.
            With a bit of experience you'll be able to easily tell one from the other.


            ​​​​
            ​​​​​​



            ​​​
            The window on the red balloon sometimes wrinkles up a bit compared to the rest of the balloon when it is deflated, so I am not sure if its just the dye, or truly a weak point in the latex.

            Comment

            • Hazloon24
              Senior Member
              • Jun 2023
              • 150

              #7
              Originally posted by O'Dragon
              Would also say don’t worry. Had some like these on new rifco 40‘s and panicked as you did but later I just went for it and they held up perfectly. Best rides in a long time!
              Good to know! I haven't built the confidence up yet to sit on my bigger balloons, but I will keep it in mind!

              Comment

              • O'Dragon
                Senior Member
                • Jan 2024
                • 298

                #8
                Yeah start slowly and take your time building confidence and you‘ll have amazing experiences! I also I think maybe starting with laying on them might even be safer than sitting as your weight gets more evenly distributed over the entire balloon whereas sitting puts your whole weight on a single small area and thus a lot of stress on only a small spot.

                I guarantee you that once you build your confidence, you will have great experiences!

                Comment

                • Dust of the Saturn
                  Stretched like space-time
                  • Feb 2018
                  • 411

                  #9
                  Originally posted by Hazloon24

                  The window on the red balloon sometimes wrinkles up a bit compared to the rest of the balloon when it is deflated, so I am not sure if its just the dye, or truly a weak point in the latex.
                  I had the same experience with a transparent smudge on a turquoise tuftex 17 which wrinkled much more compared to the rest of the body. I didn't notice at first and completely overinflated the balloon. Then when I deflated it slowly, I noticed the smudge and wrinkles, which scared me at first. Then I decided I want to give this balloon another chance and inflated it again but this time, made it slightly smaller, but still overinflated. It's holding up great!
                  1.png 3.png



                  In my experience, a lot of those transparent spots are harmless, especially the ones that come in circles. I've also encountered a small latex "bump" on the body, which you can feel while running your fingers through. That balloon also inflated fine! This one also had like 100 of these transparent circles, the balloon still overinflated fine and I even squeezed it quite a bit. It held up perfectly. I tend to avoid making them rock hard just for safety but aside from that, they're good.

                  I know we all like to think that these are somehow the "weakest link" of a balloon, but you'll be surprised. The only reliable weakspot I have seen is wrinkles around the neck, which can be seen on some stretched Cattex 19 and BSA 17. These wrinkles form right where the body and the neck meet and that's how I end up with 2 big pieces of latex, which ruptures perfectly around these wrinkles. But even then, for the balloon to pop, you'll have to severely stretch the body while keeping the neck unstretched, which in itself is undesirable.

                  I like to believe that all of those transparent spots are related to the dye and not to the latex, which means it's just a cosmetic thing. As for the wrinkles, they matter, but as long as you're not abusing the shit out of the balloon, good brands will hold. It's always better to get first hand experience so try to overcome your suspicions or get a partner to inflate one of these balloons for you. Most non-looners don't care or check for weakspots on balloons, they just go for it.
                  Stretched like space-time

                  Comment

                  • cl23
                    Senior Member
                    • May 2022
                    • 381

                    #10
                    These spots usually occur, when there are small air bubbles in the liquid latex during manufacturing the balloon molds are dipped into. This can also happen to transparent balloons, latex gloves etc.

                    Most of these weak spots are safe. It can happen, that, if the latex is really thin at this spot, it opens and the balloon deflates through this hole. Rarely, balloons burst due to these spots, but it may happen.
                    I sometimes put transparent sticky tape over these spots when the balloon is 80% inflated. Then i inflate the balloon to 100%, so the tape stretches a little bit and sticks tighter.

                    You can also fix weak spots with prevulcanized liquid latex. This is not expensive and has the advantage, that you can deflate and inflate the balloons as you like. The tape doesn't stick anymore, if you deflate the balloon.

                    Comment

                    Working...